DSPIC33CK64MC102T-I/M6 - 100MHz 64KB Flash DSC | Microchip
部品番号: DSPIC33CK64MC102T-I/M6 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
DSPIC33CK64MC102T-I/M6 概要
A Digital Signal Controller combines the computational throughput of a digital signal processor with the peripheral integration and deterministic behavior of a microcontroller. Within the power-management hierarchy, a DSC sits between general-purpose MCUs and dedicated DSPs, making it the standard choice for closed-loop real-time control systems such as Field-Oriented Control (FOC) motor drives, where sensing, computation, and PWM generation must complete within a single control period.
Key features of the DSPIC33CK64MC102T-I/M6 include operation from 3.0 V to 3.6 V across -40C to +125C (up to 100 MIPS), three integrated operational amplifiers, one comparator, a 12-bit ADC, high-resolution PWM, and a Programmable Gain Amplifier-based analog front end suited for advanced sensing. The program Flash includes ECC and fault-injection test support, and the SRAM includes Memory Built-In Self-Test (MBIST), supporting functional safety (FuSa) development per DigiKey categorization.
Architecturally, the modified Harvard dsPIC33CK core executes DSP instructions with single-cycle MAC operation and deterministic interrupt latency, essential for tight control loops. Four DMA channels offload data movement between ADC results and RAM without CPU intervention, freeing cycles for the control algorithm. Per Mouser listing, the part integrates 3 op amps, 1 comparator, and PTG (Peripheral Trigger Generator) hardware.
Typical applications include brushless DC and PMSM motor control (the Microchip low-voltage fan reference design DS50003310A uses this device), digital power supplies and LED drivers, and advanced sensing plus capacitive touch systems where the on-chip op amps condition sensor signals ahead of the 12-bit ADC.
Design consideration: the 3.0 V to 3.6 V supply range requires a clean 3.3 V rail; in the WeEn/Microchip fan reference design, a MIC5205 LDO derives this rail from 10 V, and adequate decoupling plus a low-impedance analog ground are recommended for ADC accuracy.
This page synthesizes verified distributor listings, drop-in alternative analysis, and application guidance not consolidated in the manufacturer datasheet.
ドロップイン代替品: DSPIC33CK64MC102T-I/M6 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DSPIC33CK64MC102T-I/M6 （同一形状・フットプリント） — 相違点: ADC Resolution, Core, Packaging.
クイック比較ツール — 並列比較する代替部品を選択:
DSPIC33CK32MC102T-I/M6
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
DSPIC33CK64MC102T-E/M6
✅ ドロップイン📋 参考代替品（カタログ未掲載）
DSPIC33CK32MC102T-E/M6
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
DSPIC33CK64MC103T-I/M6
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
DSPIC33CK32MC103T-I/M6
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
DSPIC33CK64MC102T-I/M6 最大定格＆電気的特性
| Core | dsPIC33CK 16-bit DSC |
| Core Count | 1 |
| 最大クロック周波数 | 100 MHz |
| Maximum Performance | 100 MIPS |
| Program Flash Size | 64 KB (with ECC) |
| Data RAM Size | 8 KB SRAM (with MBIST) |
| 動作電源電圧 | 3 V to 3.6 V |
| 動作温度範囲 | -40C to +125C |
| パッケージ / ケース | UQFN-28 (4x4 mm) |
| 実装スタイル | SMD/SMT |
| On-chip Op Amps | 3 |
| On-chip Comparators | 1 |
| ADC Resolution | 12-bit |
| Product Type | Digital Signal Controllers & Processors (DSC/DSP) |
| Packaging | Reel (Tape and Reel) |
| Functional Safety Support | Yes (FuSa per DigiKey listing) |
| Special Peripherals | PTG (Peripheral Trigger Generator), High-Resolution PWM |
DSPIC33CK64MC102T-I/M6 uqfn-28 (4x4 mm) ピン配置ガイド
DSPIC33CK64MC102T-I/M6 (uqfn-28 (4x4 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: DSPIC33CK64MC102T-I/M6.
詳細は データシート をご参照ください。
主な用途
DSPIC33CK64MC102T-I/M6 の用途: 6 件s: BLDC/PMSM Motor Control (FOC), Digital Power Supplies, Advanced Sensing Systems, Capacitive Touch Interfaces, Function Safety (FuSa) Industrial Control, Appliance and Consumer Motor Products.
BLDC/PMSM Motor Control (FOC)
The DSPIC33CK64MC102T-I/M6 is engineered for Field-Oriented Control of brushless DC and permanent-magnet synchronous motors, running the full current/speed control loop at its 100 MIPS dsPIC33CK core with deterministic interrupt latency. Its high-resolution PWM generates the inverter gate signals while the 12-bit ADC samples phase currents, and the three integrated op amps amplify shunt-resistor current signals on-chip, eliminating external amplifiers and reducing BOM cost. Microchip's low-voltage fan reference design DS50003310A demonstrates this exact topology. Trade-off: single-core architecture handles one control loop at a time, which is sufficient for most single-motor FOC designs but not for multi-axis simultaneous control.
おすすめ
Digital Power Supplies
In digital AC-DC and DC-DC power supplies, the DSPIC33CK64MC102T-I/M6 closes voltage and current feedback loops using its 100 MHz core for fast proportional-integral control, its high-resolution PWM for precise duty-cycle adjustment and phase-shifted bridge driving, and its 12-bit ADC plus on-chip op amp and comparator for sensing and fast overcurrent protection. The 3.0 V to 3.6 V supply range requires a clean regulated 3.3 V rail derived from the converter output or an auxiliary winding. The ECC-protected Flash guards control-firmware integrity in power systems where a corrupted instruction could cause a destructive fault, an advantage over non-ECC general-purpose MCUs in this domain.
おすすめ
Advanced Sensing Systems
Sensor signal chains benefit directly from the analog integration of the DSPIC33CK64MC102T-I/M6: three on-chip operational amplifiers condition bridge, thermocouple, or shunt signals ahead of the 12-bit ADC, while the Peripheral Trigger Generator (PTG) sequences ADC sampling and DMA transfers autonomously, sustaining deterministic sample timing without CPU overhead. The 100 MIPS core applies digital filtering and calibration math on captured data in real time. With -40C to +125C industrial temperature rating and SRAM MBIST, the device suits factory automation and environmental monitoring nodes. Design consideration: op amp bandwidth and gain-bandwidth limits must be checked against target sensor signal frequencies per the family datasheet.
おすすめ
Capacitive Touch Interfaces
Microchip targets touch applications with the dsPIC33CK MC10X family, and the DSPIC33CK64MC102T-I/M6 implements capacitive touch sensing by using its 12-bit ADC and internal charge-transfer measurement driven by the 100 MHz core, with the three op amps available for signal conditioning in noisy environments. Detection and debounce algorithms run in firmware alongside the main application, so 64 KB Flash accommodates a touch library plus motor or communication code simultaneously. Deterministic execution keeps touch response latency consistent across scan channels. The 4x4 mm UQFN-28 footprint fits compact appliance and consumer control panels where button area dominates PCB space.
おすすめ
Function Safety (FuSa) Industrial Control
The DSPIC33CK64MC102T-I/M6 carries functional-safety-oriented hardware: 64 KB program Flash with ECC and a fault-injection testing feature, plus 8 KB SRAM with Memory Built-In Self-Test (MBIST), allowing diagnostic coverage required by safety-oriented industrial equipment such as motor drives with safe-stop functions, robotic actuators, and process-control units. DigiKey explicitly categorizes this MPN under dsPIC Functional Safety (FuSa) Microcontroller ICs. The 100 MIPS core executes the control algorithm while diagnostics run in idle slots, and the -40C to +125C industrial rating covers typical cabinet environments. Developers should pair the hardware with Microchip safety manuals and libraries rather than relying on hardware alone.
おすすめ
Appliance and Consumer Motor Products
Fans, pumps, compressors, and small appliances use the DSPIC33CK64MC102T-I/M6 as a single-chip motor controller: it reads hall or sensorless back-EMF feedback through the ADC, runs commutation or FOC firmware in the 100 MIPS core, and drives the power stage with high-resolution PWM. The integrated op amps and comparator reduce external component count, important at consumer price points, and CNX Software's May 2026 report highlights dsPIC33CK Value Line pricing from $0.51 for cost-optimized motor control designs. The 4x4 mm UQFN-28 package and -40C to +125C range fit sealed appliance enclosures with elevated internal temperatures.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DSPIC33CK64MC102T-I/M6 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DSPIC33CK32MC102T-I/M6 | DSPIC33CK64MC102T-E/M6 | DSPIC33CK64MC103T-I/M6 | DSPIC33CK32MC103T-I/M6 |
|---|---|---|---|---|---|
| Package | UQFN-28 (4x4 mm) | UQFN-28 (4x4 mm) - same | UQFN-28 (4x4 mm) - same | UQFN-28 (4x4 mm) - same | UQFN-28 (4x4 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Performance | dsPIC33CK, 100 MHz / 100 MIPS | dsPIC33CK, 100 MHz / 100 MIPS | dsPIC33CK, 100 MHz / 100 MIPS | dsPIC33CK, 100 MHz / 100 MIPS | dsPIC33CK, 100 MHz / 100 MIPS |
| Program Flash | 64 KB (ECC) | 32 KB (ECC) | 64 KB (ECC) | 64 KB (ECC) | 32 KB (ECC) |
| Data SRAM | 8 KB (MBIST) | 8 KB (MBIST) | 8 KB (MBIST) | 8 KB (MBIST) | 8 KB (MBIST) |
| Operating Temperature | -40C to +125C (industrial) | -40C to +125C | Extended (-E suffix) | -40C to +125C | -40C to +125C |
| On-chip Op Amps / Comparators | 3 op amps / 1 comparator | 3 op amps / 1 comparator | 3 op amps / 1 comparator | Enhanced analog set | Enhanced analog set |
主な差別化要因
- Double the program Flash at identical footprint and cost tier （vs DSPIC33CK32MC102T-I/M6)
- Industrial temperature rating keeps cost down versus extended grade （vs DSPIC33CK64MC102T-E/M6)
- On-chip analog integration reduces BOM （vs DSPIC33CK32MC102T-I/M6 (and generic MCUs without op amps))
設計ノート
Supply the DSPIC33CK64MC102T-I/M6 from a regulated 3.3 V rail within the 3.0 V to 3.6 V datasheet window. In Microchip's low-voltage fan reference design (DS50003310A), a MIC5205 LDO derives the DSC rail from a 10 V bus; a similar LDO or buck with adequate current margin works here. Decouple each VDD pin with 100 nF ceramic capacitance placed within 2 mm of the pin, plus bulk 10 uF near the device. Avoid routing inverter gate-drive return currents through the DSC ground path - use a single-point analog/digital ground junction beneath the UQFN exposed pad.
The UQFN-28 (4x4 mm) package has 0.4-0.5 mm pitch lands and an exposed thermal pad that must be soldered to a grounded copper keep-out for both heat dissipation and signal return. Follow the Microchip family datasheet land-pattern dimensions exactly; use a windowed solder-mask paste stencil (approximately 50-70% pad coverage on the center pad) to prevent bridging on the fine-pitch perimeter lands. Peripheral remapping (PPS) lets you allocate PWM and UART pins to optimal physical locations, so route the high-current PWM traces first with short, wide geometry before committing microcontroller I/O.
The T suffix denotes tape-and-reel delivery - confirm your pick-and-place supports the reel, or order cut-tape quantities. The M6 package is UQFN 4x4; do not confuse it with the /2N (28-pin UQFN 5x5) or /SS (SSOP) package variants of the same silicon, which are NOT footprints-compatible. Flash ECC is active by default and fault-injection features are intended for safety validation - consult the Microchip functional safety documentation before disabling or relying on these diagnostics. ADC accuracy depends on clean AVDD and reference; do not share the analog reference rail with PWM gate-driver supplies.
Estimated: at 100 MIPS with typical activity, the dsPIC33CK core draws on the order of tens of milliwatts; using an indicative 100 mW dissipation and the UQFN-28 exposed-pad thermal resistance of roughly 40-50 C/W on a nominal 2-layer board, junction rise above ambient is only about 4-5 C, well within the -40C to +125C rating. The estimate uses assumed input values because exact theta-JA was not in the verified data - confirm the figure in the datasheet electrical characteristics table for your PCB stack-up.
コンプライアンス情報
Distributor listings for this current-production Microchip part indicate standard RoHS/lead-free production status, but explicit RoHS/REACH/halogen-free certificate values were not itemized in the verified web data as of 2026-09-23; request the material declaration from Microchip. Not an automotive AEC-Q100-listed MPN in the provided data.
