DSPIC33EP128MU204-I/ML - 16-bit DSC 128KB Flash 70 MIPS | Microchip
部品番号: DSPIC33EP128MU204-I/ML ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $5.95 | $5.95 |
| 10 | $5.42 | $54.20 |
| 100 | $4.95 | $495.00 |
| 500 | $4.55 | $2,275.00 |
| 1,000 | $4.2 | $4,200.00 |
DSPIC33EP128MU204-I/ML 概要
A Digital Signal Controller combines the compute architecture of a digital signal processor with the peripheral set, interrupt structure, and ease of use of a microcontroller. In the system hierarchy, the dsPIC33EP family sits between general-purpose MCUs and full DSPs, making it the preferred choice for embedded control tasks that also need fast math: motor control loops, digital power conversion, and signal conditioning.
Key features include a 16-bit pipeline core executing up to 70 MIPS, two 16-bit on-chip program spaces, a 16-channel 12-bit ADC with up to 1.1 Msps conversion rate, USB 2.0 full-speed On-The-Go, three 16-bit timers, and multiple UART, SPI, and I2C ports. Multiple PWM modules support motor control and switching power supplies directly.
The dsPIC33EP architecture uses a modified Harvard bus with dedicated hardware multiply, divide, and barrel-shifter units, plus DSP instruction support (MAC, DSP addressing modes) that accelerates FIR/IIR filtering and control algorithms. Flash is reprogrammable in-circuit, and the device operates from a 3.0 V to 3.6 V supply over the industrial temperature range of -40C to +85C, indicated by the -I suffix.
Typical applications include brushless DC and PMSM motor drives, USB-connected industrial instruments, digital LED lighting, and sensor acquisition systems that benefit from the 12-bit ADC and DSP math.
Design consideration: budget PCB area for the QFN exposed thermal pad and follow Microchip's clock and USB layout guidance; at 70 MIPS the device tolerates minor layout imperfections, but USB signal routing and decoupling quality directly determine compliance.
This page synthesizes distributor stock data, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
ドロップイン代替品: DSPIC33EP128MU204-I/ML — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DSPIC33EP128MU204-I/ML （同一形状・フットプリント） — 相違点: Package, Operating Temperature, Core, Program Memory (Flash), Communication Interfaces.
クイック比較ツール — 並列比較する代替部品を選択:
DSPIC33EP256MU204-I/ML
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
DSPIC33EP64MU204-I/ML
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
DSPIC33EP128MC204-I/ML
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$2.98 / 個
データシートを見る →DSPIC33EP128MU204-H/ML
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$4.15 / 個
データシートを見る →DSPIC33EP128GM204-I/ML
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
DSPIC33EP128MU204-I/ML 最大定格＆電気的特性
| Core Type | 16-bit dsPIC33EP DSC |
| Program Memory (Flash) | 128 KB |
| RAM | 16 KB |
| Maximum CPU Speed | 70 MIPS |
| ADC Resolution | 12-bit |
| ADC Channels | 16 |
| ADC Sampling Rate | 1.1 Msps |
| USB | USB 2.0 full-speed On-The-Go |
| Operating Voltage | 3.0 V to 3.6 V |
| 動作温度 | -40C to +85C |
| パッケージ | 44-pin QFN (ML) |
| Timers | 3 x 16-bit |
| Communication Interfaces | UART, SPI, I2C, ECAN, USB |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
DSPIC33EP128MU204-I/ML 44-pin qfn (ml) ピン配置ガイド
DSPIC33EP128MU204-I/ML (44-pin qfn (ml) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: DSPIC33EP128MU204-I/ML.
詳細は データシート をご参照ください。
主な用途
DSPIC33EP128MU204-I/ML の用途: 6 件s: Brushless DC and PMSM Motor Control, USB Industrial Instrumentation, Digital Power Conversion and LED Lighting, Sensor Acquisition and Signal Conditioning, Automotive-Adjacent ECAN Networking Nodes, Audio Signal Processing and DSP Preprocessing.
Brushless DC and PMSM Motor Control
The DSPIC33EP128MU204-I/ML fits BLDC and PMSM drives because its 70 MIPS DSP core executes field-oriented control loops in well under one PWM period, and its 12-bit ADC (1.1 Msps) samples phase currents and bus voltage synchronously with the PWM trigger. Microchip's Motor Control family application notes provide reference FOC and sensorless (SMO/BEMF) firmware stacks that port directly to this device. The motor-control PWM module generates complementary outputs with dead-time insertion, supporting three-phase inverters without external dead-time logic. For USB-connected drives, the integrated USB OTG provides configuration and telemetry links. The trade-off versus the MC204 variant is that MU204 users implement PWM features via the standard module; if maximum PWM concurrency is required, consider the pin-compatible DSPIC33EP128MC204.
おすすめ
USB Industrial Instrumentation
With USB 2.0 full-speed On-The-Go integrated on-chip, the DSPIC33EP128MU204-I/ML is a natural controller for USB-connected measurement devices: data loggers, sensor front ends, and bench instruments. The 16-channel 12-bit ADC digitizes analog inputs at up to 1.1 Msps, while the DSP MAC instructions run calibration, filtering (FIR/IIR), and FFT-based analysis on-device, sending only processed results over USB. Microchip's MLA USB device stack supports HID, CDC (virtual COM port), and MSD classes, minimizing host driver work. The device runs from a single 3.3 V rail with bus-powered designs feasible due to uA-class sleep modes. Design consideration: route the USB differential pair with 90-ohm controlled impedance and derive a clean 48 MHz USB clock from the PLL per the clock section of the datasheet.
おすすめ
Digital Power Conversion and LED Lighting
Switching power supplies and high-power LED drivers benefit from the DSPIC33EP128MU204-I/ML's tightly coupled ADC-to-PWM path: the 12-bit ADC is triggered directly by the PWM module, enabling current-mode control loops with microsecond-scale response. The 70 MIPS core executes average-current-mode and peak-current-mode control, power-factor-correction algorithms, and LLCC/Buck topologies; Microchip's Digital Power reference designs cover these directly. The QFN-44 footprint keeps the controller compact near the power stage. For digitally addressed lighting systems, the UART, SPI, and I2C ports interface to DALI, DMX, or addressable LED chains, while ECAN joins luminaires to building networks. Thermal design note: at full clock speed the device dissipates modest power, but keep it clear of switch-node copper to avoid noise coupling into the ADC.
おすすめ
Sensor Acquisition and Signal Conditioning
The DSPIC33EP128MU204-I/ML serves as an intelligent sensor hub: 16 ADC channels at 12-bit resolution and 1.1 Msps capture multi-channel analog inputs, while the DSP engine applies offset removal, gain calibration, and digital filtering in real time. The DSP addressing modes and single-cycle MAC make FIR filtering efficient enough to run on all sampled channels concurrently. Conditioned results stream out over USB OTG, ECAN, or UART, so one device replaces separate ADC-plus-processor chains. Industrial temperature rating (-40C to +85C) allows deployment in unconditioned environments. Design tip: place a small RC anti-alias filter before each ADC input and use the internal VREF+/VREF- option to improve absolute accuracy; conversion sequencing can be scanned automatically by the ADC module without core intervention, freeing CPU cycles for processing.
おすすめ
Automotive-Adjacent ECAN Networking Nodes
Although not AEC-Q100 qualified (use the -E grade and Microchip automotive variants for that), the industrial-grade DSPIC33EP128MU204-I/ML is widely used in off-road, agricultural, and marine ECAN nodes. The on-chip ECAN module implements CAN 2.0B with up to 1 Mbps operation and hardware message buffers, offloading the CPU from frame handling. Combined with the 12-bit ADC for local sensing and the 70 MIPS core for protocol abstraction and diagnostics, one device forms a complete intelligent node. The -E temperature variant extends operation to +125C for under-hood-adjacent enclosures. Layout recommendation: keep the CAN transceiver within 20 mm of the ECAN pins, terminate the bus with 120 ohms at both ends, and provide transient protection at the connector per standard industrial CAN practice.
おすすめ
Audio Signal Processing and DSP Preprocessing
The DSP-enhanced core of the DSPIC33EP128MU204-I/ML handles moderate-rate audio tasks: single-cycle MAC with DSP addressing runs FIR/IIR filters, and the device can implement effects processors, audio level meters, and communication-quality codecs. While professional audio typically demands dedicated CODECs with higher SNR, this DSC excels where audio processing is a subsystem of a control application - e.g., voice prompts in industrial equipment, alarm tone synthesis, and acoustic feedback detection in communication devices. The SPI port connects to standard audio CODECs, and 16 KB RAM holds filter state and buffers for moderate block sizes. Performance consideration: at 70 MIPS with 16-bit fixed-point math, budget roughly one MAC per sample per filter tap; reserve CPU headroom for the control loop if audio runs concurrently with regulation tasks.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DSPIC33EP128MU204-I/ML — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DSPIC33EP256MU204-I/ML | DSPIC33EP64MU204-I/ML | DSPIC33EP128MC204-I/ML | DSPIC33EP128MU204-H/ML | DSPIC33EP128GM204-I/ML |
|---|---|---|---|---|---|---|
| Package | QFN-44 (ML) | QFN-44 (ML) - same | QFN-44 (ML) - same | QFN-44 (ML) - same | QFN-44 (ML) - same | QFN-44 (ML) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 128 KB | 256 KB | 64 KB | 128 KB | 128 KB | 128 KB |
| RAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| Core Speed | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS |
| ADC | 12-bit, 16-ch, 1.1 Msps | 12-bit, 16-ch, 1.1 Msps | 12-bit, 16-ch, 1.1 Msps | 12-bit, 16-ch, 1.1 Msps | 12-bit, 16-ch, 1.1 Msps | 12-bit, 1.1 Msps |
| Temperature Range | -40C to +85C (industrial) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +125C (extended) | -40C to +85C |
主な差別化要因
- Integrated USB 2.0 full-speed On-The-Go （vs DSPIC33EP128MC204-I/ML)
- Cost-optimized 128 KB point in the MU204 flash ladder （vs DSPIC33EP256MU204-I/ML)
- Industrial temperature grade availability （vs DSPIC33EP128MU204-H/ML)
設計ノート
The 44-pin QFN (ML) package includes an exposed die-attach pad on the underside that must be soldered to a grounded copper pour for reliability, even though most thermal load is modest for this device. Use a 4x4 or 5x5 via array (approx. 0.3 mm vias) under the pad to tie it to the ground plane. QFN leads are short, so use solder paste stencil aperture design per IPC QFN land-pattern guidance and verify with X-ray or AT inspection on first articles to avoid voiding under the pad.
Provide one 100 nF ceramic capacitor immediately adjacent to each VDD/VSS pin pair, plus one 4.7 uF to 10 uF bulk capacitor near the device. The -I grade part requires 3.0 V to 3.6 V; a 3.3 V LDO or buck with +-3% tolerance is standard. If using the USB OTG in host mode, budget bus current separately. Estimated: at 70 MIPS, current draw is in the tens-of-mA class - verify exact figures in the manufacturer datasheet current-vs-frequency tables before finalizing regulator sizing.
Route the USB D+/D- pair as a 90-ohm differential pair with length matching within 1 mm, and keep the 48 MHz USB PLL clock path short. Keep ADC inputs away from PWM switch nodes and high di/dt loops; use series RC anti-alias filters (e.g., 100 ohm + 1 nF) on analog channels. Reserve the ICSP header (MCLR, PGD, PGC, VDD, VSS) on all production boards for field programming with PICkit/ICD/REAL ICE tools.
Common mistakes with this family: (1) forgetting that CONFIG word settings (oscillator, watchdog, code protection) are burned at programming time and differ from runtime configuration; (2) underestimating PLL setup requirements - USB requires an exact 48 MHz derived clock, so crystal choice must allow a valid PLL divider chain; (3) driving ADC inputs above VDD causing injection current. Follow the oscillator section of the manufacturer datasheet when selecting crystals for USB operation.
コンプライアンス情報
RoHS compliant per distributor listings (DigiKey/Mouser) for the -I/ML ordering code. Not an automotive AEC-Q100 part; use Microchip automotive-qualified dsPIC33 variants for such applications.
