DSPIC33EP512MC204T-E/ML - 16-bit 512KB DSC 60MIPS | Microchip
部品番号: DSPIC33EP512MC204T-E/ML ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $7.42 | $7.42 |
| 10 | $6.71 | $67.10 |
| 100 | $5.98 | $598.00 |
| 500 | $5.36 | $2,680.00 |
| 1,000 | $4.83 | $4,830.00 |
DSPIC33EP512MC204T-E/ML 概要
A digital signal controller combines the compute architecture of a microcontroller with the math acceleration of a digital signal processor. In the power-management hierarchy, the dsPIC33EP family sits within Microchip's 16-bit MCU/DSC portfolio, where a single core executes control loops, communication stacks, and DSP routines - making DSCs the de-facto choice for closed-loop motor control, digital power conversion, and sensing systems that need deterministic, cycle-accurate behavior.
Key features of this device include a 16-bit dsPIC core with DSP engine and single-cycle MAC, dedicated high-speed MCPWM (motor control PWM) modules with complementary outputs and dead-time insertion, quadrature encoder interface (QEI) inputs for position feedback, three integrated operational amplifiers, four analog comparators, and a CTMU (charge time measurement unit) for capacitive-touch or precision timing measurement. Four DMA channels offload data movement from the core, and five 16-bit timers support complex time bases.
Technically, the dsPIC33EP architecture runs from a 3.0V to 3.6V single supply, with an internal PLL allowing the core to operate at 60 MIPS (some family documentation cites a 70 MIPS-capable core clock depending on device grading). CMOS process technology keeps dynamic power low, while the 8x8 mm VQFN exposed pad provides a low thermal resistance path to the PCB copper pour - essential when driving power stages through the PWM outputs in compact automotive ECUs.
Typical applications include BLDC and PMSM motor control with field-oriented control (FOC), automotive auxiliary actuators and pumps, digital power supplies and PFC stages, and industrial sensor signal conditioning using the on-chip op amps and CTMU.
For design, budget decoupling of at least 100 nF per VDD pin plus bulk capacitance at the 3.3V rail, and route PWM outputs away from analog inputs feeding the op amps to protect the 10/12-bit ADC signal path from switching noise.
This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.
ドロップイン代替品: DSPIC33EP512MC204T-E/ML — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DSPIC33EP512MC204T-E/ML （同一形状・フットプリント） — 相違点: Package, Operating Temperature, Core Architecture, Product Family, Qualification.
クイック比較ツール — 並列比較する代替部品を選択:
DSPIC33EP256MC204T-E/ML
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$3.9 / 個
データシートを見る →DSPIC33EP512MC204T-I/ML
✅ ドロップイン✓ 在庫あり
$3.85 / 個
データシートを見る →DSPIC33EP64MC204T-I/ML
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$2.61 / 個
データシートを見る →DSPIC33EP32MC204T-E/ML
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$3 / 個
データシートを見る →DSPIC33EP128MC204T-I/ML
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$3.45 / 個
データシートを見る →DSPIC33EP512MC204T-E/ML 最大定格＆電気的特性
| Core | 16-bit dsPIC DSC |
| Core Speed | 60 MIPS |
| Program Memory (FLASH) | 512 KB (170K x 24) |
| 電源電圧 | 3.0 V to 3.6 V |
| 動作温度 | -40C to +125C (E grade) |
| パッケージ | 44-VQFN (8x8 mm), Exposed Pad |
| 実装タイプ | Surface Mount |
| Qualification | AEC-Q100 (Automotive) |
| Motor Control PWM | MCPWM module |
| Quadrature Encoder Interface | QEI |
| On-chip Op Amps | 3 |
| On-chip Comparators | 4 |
| CTMU | Yes (Charge Time Measurement Unit) |
| DMA Channels | 4 |
| Timers | 5 x 16-bit |
| Packaging | Tape & Reel (T suffix) |
DSPIC33EP512MC204T-E/ML 44-vqfn (8x8 mm), exposed pad ピン配置ガイド
DSPIC33EP512MC204T-E/ML (44-vqfn (8x8 mm), exposed pad パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: DSPIC33EP512MC204T-E/ML.
詳細は データシート をご参照ください。
主な用途
DSPIC33EP512MC204T-E/ML の用途: 6 件s: BLDC/PMSM Field-Oriented Motor Control, Automotive Auxiliary Actuators and Pumps, Digital Power Supplies and PFC, Industrial Sensor Signal Conditioning, Automotive Body Electronics and Lighting Control, Test and Measurement Instrumentation.
BLDC/PMSM Field-Oriented Motor Control
The DSPIC33EP512MC204T-E/ML fits sensorless and sensored FOC drives because its 60 MIPS core executes Clarke/Park transforms and PI current loops within a single 20 kHz PWM period, while the MCPWM module generates three complementary PWM pairs with hardware dead-time insertion. The QEI interface decodes encoder position directly, and the three on-chip op amps amplify low-side shunt currents before ADC sampling, eliminating external amplifier stages. Placed at the center of the drive board, the controller's 512KB FLASH holds full FOC firmware plus field-weakening and communication stacks, and the 8x8 mm VQFN exposed pad dissipates switching-era heat into the ground pour efficiently.
おすすめ
Automotive Auxiliary Actuators and Pumps
The AEC-Q100 qualification and -40C to +125C E temperature grade make the DSPIC33EP512MC204T-E/ML suitable for under-hood pumps, electronic water valves, throttle actuators, and HVAC blowers. Its 512KB FLASH retains diagnostic and functional-safety logging code alongside control firmware, while four comparators provide fast hardware overcurrent trip paths independent of software latency. The CTMU supports capacitive user interfaces in cabin controls on the same silicon family. In the power tree, a 3.0V-3.6V regulator feeds VDD with 100 nF decoupling per pin, and the 44-QFN exposed pad bonded to the PCB ground plane provides the thermal path needed for continuous actuator drive duty cycles in engine-bay ambients up to 125C.
おすすめ
Digital Power Supplies and PFC
Switching power supplies benefit from the controller's deterministic 60 MIPS execution: voltage- and current-mode loops close at 100-500 kHz switching frequencies with cycle-by-cycle current limiting implemented in the comparators rather than in software. The 12-bit ADC sampled via DMA keeps processor bandwidth free for supervisory functions such as PMBus-style telemetry. The 512KB FLASH accommodates soft-start ramp tables and gain-scheduling compensation curves across wide line/load ranges. Designers place the DSPIC33EP512MC204T-E/ML on the control side of the isolation barrier, use the MCPWM's complementary outputs with programmable dead time to drive half-bridge gate drivers, and exploit the exposed-pad QFN's low thermal impedance to keep junction temperature within the 125C rating in confined power-supply enclosures.
おすすめ
Industrial Sensor Signal Conditioning
Three integrated operational amplifiers and the CTMU allow the DSPIC33EP512MC204T-E/ML to condition sensor signals directly on-chip: the op amps configure as gain stages for thermocouple, bridge, or current-shunt front ends, while the CTMU measures capacitive changes for level, proximity, or touch sensing. The 512KB FLASH stores calibration polynomials per-unit, and four DMA channels stream ADC results to RAM without core intervention, sustaining high sample rates. Running from a clean 3.3V rail with separate analog grounding connected to the exposed pad, the controller converts conditioned signals with its onboard ADC at up to 60 MIPS loop bandwidth, making it a compact single-chip replacement for discrete op-amp-plus-MCU sensor boards in factory automation.
おすすめ
Automotive Body Electronics and Lighting Control
For headlamp levelling motors, pump modules, and smart actuator nodes, the E-grade DSPIC33EP512MC204T-E/ML combines motor control with network connectivity: its UART/SPI/I2C ports pair with CAN transceivers for in-vehicle networking, and 512KB FLASH holds flash-loader code enabling field OTA-style updates. MCPWM outputs drive brushed-DC H-bridges with current sensing through the on-chip comparators for stall detection. The -40C to +125C range covers worst-case packaging locations, and AEC-Q100 qualification satisfies automotive quality gates. The 44-QFN (8x8 mm) footprint fits body-control module PCBs with two-sided assembly, and the exposed pad keeps thermal resistance low enough for sealed, conduction-cooled modules without heatsinks.
おすすめ
Test and Measurement Instrumentation
Bench instruments and portable testers use the DSPIC33EP512MC204T-E/ML's DSP engine for real-time waveform processing, averaging, and FFT-based analysis at 60 MIPS with single-cycle MAC throughput. The CTMU provides precision time-interval measurement for capacitance and time-domain reflectometry functions, and DMA-driven ADC sampling guarantees uniform timestamps for waveform capture. The 512KB FLASH stores multiple instrument personalities and calibration constants, while UART/USB-bridge connectivity streams data to host PCs. Because the device tolerates -40C to +125C in the E grade, handheld instruments used outdoors remain within specification. Designers dedicate one op amp to input buffering and leverage the QFN exposed pad as a star ground reference that protects the analog front end from digital return noise.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DSPIC33EP512MC204T-E/ML — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DSPIC33EP256MC204T-E/ML | DSPIC33EP512MC204T-I/ML | DSPIC33EP64MC204T-I/ML | DSPIC33EP32MC204T-E/ML | DSPIC33EP128MC204T-I/ML |
|---|---|---|---|---|---|---|
| Package | 44-VQFN (ML, 8x8 mm) Exposed Pad | 44-VQFN (ML, 8x8 mm) - same | 44-VQFN (ML, 8x8 mm) - same | 44-VQFN (ML, 8x8 mm) - same | 44-VQFN (ML, 8x8 mm) - same | 44-VQFN (ML, 8x8 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| FLASH Program Memory | 512 KB (170K x 24) | 256 KB | 512 KB | 64 KB | 32 KB | 128 KB |
| Core Speed | 60 MIPS | 60 MIPS | 60 MIPS | 60 MIPS | 60 MIPS | 60 MIPS |
| Operating Temperature | -40C to +125C (E) | -40C to +125C (E) | -40C to +85C (I) | -40C to +85C (I) | -40C to +125C (E) | -40C to +85C (I) |
| AEC-Q100 | Qualified | Qualified | Industrial grade | Industrial grade | Qualified | Industrial grade |
| Peripheral Set (MCPWM/QEI/OpAmp/Comparator/CTMU) | MCPWM, QEI, 3 OpAmp, 4 Comp, CTMU | Identical | Identical | Identical | Identical | Identical |
主な差別化要因
- Maximum FLASH in the MC204 family for this footprint （vs DSPIC33EP256MC204T-E/ML)
- Automotive E-grade temperature and AEC-Q100 （vs DSPIC33EP512MC204T-I/ML)
- Integrated analog front end （vs DSPIC33EP64MC204T-I/ML)
設計ノート
The DSPIC33EP512MC204T-E/ML requires a regulated 3.0V-3.6V supply with all VDD pins decoupled by 100 nF ceramic capacitors placed within 2 mm of each pin, plus at least one 4.7-10 uF bulk capacitor per device. Microchip's dsPIC33EP family reference layouts also mandate proper VDDCORE/VCAP decoupling; omitting or misplacing the VCAP capacitor is a documented cause of brown-out and erratic PLL lock at 60 MIPS operation.
Solder the 44-QFN (8x8 mm) exposed pad to a contiguous ground pour with an array of thermal vias (typically a 4x4 via pattern of 0.3 mm vias) to achieve the datasheet thermal performance. This exposed pad is also the primary ground return for the ADC and op amps - do not split analog and digital returns beneath the package; instead use a single solid plane with careful component placement to control return currents.
The E suffix (-40C to +125C) is required for AEC-Q100 automotive use; substituting the I-grade part in an automotive BOM is a qualification failure even though the die is identical. Also, when migrating from DSPIC33EP256MC204T-E/ML to this 512KB part, verify linker script and page-erase settings in your project, since FLASH size differences require updated memory map definitions in MPLAB X projects.
Route MCPWM outputs away from analog inputs feeding the on-chip op amps and ADC. Keep shunt-amplifier traces short and differential, and gate ADC sampling away from PWM switching edges using the MCPWM-triggered ADC conversion feature of the dsPIC33EP family to minimize switching-noise aliasing in FOC current measurements.
コンプライアンス情報
AEC-Q100 automotive qualification confirmed by Microchip USA and Hotenda listings. RoHS/lead-free status inferred from standard Microchip current-production packaging; confirm on the Microchip product page for formal certification documents.
