DSPIC33EP64MC204-I/TL - 70MIPS 64KB DSC | Microchip | Motor Control
部品番号: DSPIC33EP64MC204-I/TL ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $4.12 | $4.12 |
| 10 | $3.75 | $37.50 |
| 100 | $3.45 | $345.00 |
| 500 | $3.25 | $1,625.00 |
| 1,000 | $3.07 | $3,070.00 |
DSPIC33EP64MC204-I/TL 概要
A digital signal controller combines the compute architecture of a microcontroller with the math acceleration of a digital signal processor. In the power-management hierarchy, the dsPIC33EP family sits above basic 16-bit MCUs and below dedicated DSPs, offering a single-chip solution that runs control loops, handles communications, and drives power electronics simultaneously. This makes DSCs the de facto standard for digital power conversion and precision motor control.
Key features include the 70 MIPS dsPIC DSC core with integrated DSP engine, 64KB Flash sized as 22K x 24 instruction words, and connectivity peripherals including I2C, SPI, UART/USART, IrDA, LINbus, and QEI. The MC variant specifically targets motor control with high-speed PWM outputs and advanced analog peripherals.
Architecturally, the device uses a 16-bit RISC pipeline with DSP instructions (MAC, MPY) and dual operand fetch, enabling single-cycle multiply-accumulate operations that sustain high-frequency current loops in field-oriented control (FOC) schemes. The 3.3V supply domain simplifies integration with modern gate drivers and level shifters.
Typical applications include brushless DC and PMSM motor drives, digital power supplies (LLC, totem-pole PFC), and industrial automation nodes requiring deterministic control-loop execution alongside serial communications.
For design, budget the Flash carefully - 64KB (22K x 24 words) is ample for FOC firmware but leaves limited headroom for protocol stacks; consider the pin-compatible DSPIC33EP128MC204-I/TL if code size grows. The exposed pad must be soldered to a ground pour for thermal and signal integrity.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
ドロップイン代替品: DSPIC33EP64MC204-I/TL — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DSPIC33EP64MC204-I/TL （同一形状・フットプリント） — 相違点: Package, Core, Data Bus Width, CPU Speed, Family.
クイック比較ツール — 並列比較する代替部品を選択:
DSPIC33EP64MC204-E/TL
✅ ドロップイン📋 参考代替品（カタログ未掲載）
DSPIC33EP128MC204-I/TL
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$3.4 / 個
データシートを見る →DSPIC33EP32MC204-I/TL
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$3.48 / 個
データシートを見る →DSPIC33EP64MC204-I/TL 最大定格＆電気的特性
| Core | dsPIC33E 16-bit DSC core |
| Core Performance | 70 MIPS |
| Program Memory Size | 64KB (22K x 24) Flash |
| Supply Voltage Range | 3 V to 3.6 V (3.3 V nominal) |
| 動作温度 | -40C to +85C (I grade) |
| パッケージ | 44-VTLA (6x6 mm) exposed pad |
| 実装タイプ | Surface Mount |
| Communication Interfaces | I2C, SPI, UART/USART, IrDA, LINbus, QEI |
| データバス幅 | 16 bit |
| Program Memory Type | Flash |
| Special Features | High-Speed PWM, advanced analog, integrated DSP engine |
| Target Applications | Precision motor control, digital power |
| Family | dsPIC33EP |
| Programming | ICSP (In-Circuit Serial Programming), MPLAB SNAP compatible |
DSPIC33EP64MC204-I/TL 44-vtla (6x6 mm) exposed pad ピン配置ガイド
DSPIC33EP64MC204-I/TL (44-vtla (6x6 mm) exposed pad パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: DSPIC33EP64MC204-I/TL.
詳細は データシート をご参照ください。
主な用途
DSPIC33EP64MC204-I/TL の用途: 6 件s: BLDC / PMSM Motor Drives, Digital Power Supplies (LLC, PFC), Industrial Automation Nodes, Robotics and Servo Drives, Embedded Sensing and IoT Edge Nodes, Automotive Auxiliary Motor Control.
BLDC / PMSM Motor Drives
The DSPIC33EP64MC204-I/TL fits brushless DC and permanent-magnet synchronous motor control because its 70 MIPS core with DSP engine executes field-oriented control math at single-cycle MAC speed, sustaining current loops at 20-50 kHz PWM frequencies. The MC variant integrates high-speed PWM with dead-time control and advanced analog for in-line current sensing, while QEI accepts quadrature encoder feedback directly. Placed as the single controller driving a three-phase inverter, it eliminates a separate DSP; the trade-off is that 64KB Flash limits room for extensive protocol stacks alongside the FOC firmware, so reserve roughly 70% for the control algorithm.
おすすめ
Digital Power Supplies (LLC, PFC)
Digital LLC converters and totem-pole PFC stages need deterministic, fast control loops - exactly what the 70 MIPS DSP core and high-speed PWM peripherals of this DSC provide. The DSPIC33EP64MC204-I/TL computes voltage-mode or current-mode compensation at loop rates of hundreds of kHz equivalent latency and adjusts PWM phase/frequency with nanosecond-scale resolution via the high-speed PWM module. Its 3.0V-3.6V supply interfaces cleanly with modern gate-driver logic. The design consideration is analog front-end accuracy: pair with a precision shunt amplifier and budget ISR cycles so the compensation loop plus protection routines complete within each PWM period.
おすすめ
Industrial Automation Nodes
Factory automation nodes need deterministic local control plus robust serial networking. The DSPIC33EP64MC204-I/TL offers UART/USART with LINbus and IrDA support, SPI and I2C for sensor/actuator expansion, and QEI for encoder-based positioning - all on one 3.3V controller. Running at 70 MIPS it can poll limit switches, compute PID motion profiles, and service communications without an RTOS overhead penalty. The industrial -40C to +85C rating covers unconditioned cabinets. Note the exposed-pad VTLA package requires a solid ground pour for both thermal relief and switching-noise containment in electrically noisy panels.
おすすめ
Robotics and Servo Drives
Robotic joint servos combine motor commutation, encoder feedback, and command interfaces - a workload matched to this DSC's peripheral set. The 70 MIPS core runs FOC commutation for each joint motor, QEI decodes incremental encoder position, and UART/I2C link to a higher-level motion planner. The integrated DSP engine keeps the 16-bit control math deterministic, giving repeatable torque ripple characteristics important in collaborative robots. With 64KB Flash, a single-joint servo loop with CAN or UART comms fits comfortably; multi-axis coordination should run on a host controller, with this part handling per-axis real-time control at up to tens of kHz.
おすすめ
Embedded Sensing and IoT Edge Nodes
Sensor-rich edge nodes benefit from the DSC's DSP instructions for on-node filtering (FIR/IIR) of accelerometer, current, or acoustic signals before transmission, reducing upstream bandwidth. The I2C and SPI ports connect digital sensors directly, UART streams data to cellular or RF modules, and the 3.3V domain matches common battery-management front ends. At 70 MIPS the part performs signal conditioning concurrently with protocol handling. The consideration is power: this is a performance-grade DSC, not an ultra-low-power MCU, so for battery-only nodes implement aggressive sleep strategies or select a low-power PIC family instead; for mains or vehicle-powered nodes, performance wins.
おすすめ
Automotive Auxiliary Motor Control
Auxiliary automotive actuators - pumps, fans, throttle bodies, window lifts - use BLDC or stepper motors that this DSC can commutate with its high-speed PWM and QEI/comparator peripherals. The 3.3V supply matches common automotive LIN/CAN transceiver logic levels, and LINbus support enables direct integration into low-cost body networks. Performance headroom from the 70 MIPS core supports sensorless algorithms (back-EMF observers) that reduce harness cost. Important: the -I temperature grade tops out at +85C; under-hood positions require the pin-compatible -E/TL (+125C) or Microchip automotive-qualified variants, and AEC-Q100 qualification must be confirmed for the specific orderable part before design-in.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DSPIC33EP64MC204-I/TL — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DSPIC33EP64MC204-E/TL | DSPIC33EP128MC204-I/TL | DSPIC33EP32MC204-I/TL |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-VTLA (6x6 mm) | 44-VTLA (6x6 mm) - same | 44-VTLA (6x6 mm) - same | 44-VTLA (6x6 mm) - same |
| Core Performance | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS |
| Flash Program Memory | 64KB (22K x 24) | 64KB (22K x 24) | 128KB (43K x 24) | 32KB |
| Operating Temperature | -40C to +85C | -40C to +125C | -40C to +85C | -40C to +85C |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| Communication Interfaces | I2C, SPI, UART, IrDA, LIN, QEI | I2C, SPI, UART, IrDA, LIN, QEI | I2C, SPI, UART, IrDA, LIN, QEI | I2C, SPI, UART, IrDA, LIN, QEI |
| Relative Cost | Baseline (~$3.07 @1k as of 2026-09-25) | Premium for extended temp | Higher (2x Flash) | Lower (cost-down) |
主な差別化要因
- Extended temperature availability in identical footprint （vs DSPIC33EP64MC204-E/TL)
- Balanced 64KB Flash for FOC plus lightweight comms （vs DSPIC33EP128MC204-I/TL)
- Right-sized memory vs cost-down variant （vs DSPIC33EP32MC204-I/TL)
設計ノート
The 44-VTLA exposed pad is not optional - solder it to a stitched ground pour on layer 2 with an array of thermal vias (0.3 mm drill, ~1 mm pitch). The pad is the primary ground return for the ADC reference and high-speed PWM switching currents; an unsoldered pad causes erratic ADC readings and ground bounce during simultaneous PWM switching. Follow Microchip's family PCB layout guidelines for dsPIC33EP QFN parts, keeping VDD decoupling (0.1uF per pin pair) within 5 mm of the balls.
Supply the part from a clean 3.3V rail (3.0V-3.6V range). Because motor-control ISRs create large step loads on the core at 70 MIPS, add bulk capacitance (4.7uF-10uF) near the supply entry in addition to per-pin 0.1uF ceramics. Keep the analog supply path isolated from gate-driver supply switching using a ferrite bead or PI filter; AVDD noise directly degrades current-sense ADC accuracy, which is the dominant error source in FOC torque ripple.
Three frequent mistakes: (1) treating /TL and /PT as interchangeable - the TQFP 10x10 and VTLA 6x6 footprints are different, so second-sourcing requires a PCB decision early; (2) under-budgeting Flash - 64KB (22K x 24) fills quickly with FOC plus a CAN/LIN stack; qualify DSPIC33EP128MC204-I/TL on the same layout as headroom insurance; (3) forgetting that the -I grade tops out at +85C - enclose-mounted drives near power stages often need the -E/TL (+125C) version.
コンプライアンス情報
Compliance data not explicitly stated in the provided web data; verify RoHS/REACH status on the Microchip product page before design-in. No AEC-Q100 qualification was stated for this orderable part.
