EFM32TG110F16-D-QFN24 - 32MHz Cortex-M3 16KB MCU | Silicon Labs
部品番号: EFM32TG110F16-D-QFN24 ✗ 生産終了EFM32TG110F16-D-QFN24 概要
A microcontroller is a programmable semiconductor that integrates a processor core, memory, digital interfaces, timers, and analog peripherals onto one device. In the system hierarchy, the EFM32TG110F16-D-QFN24 belongs to the ARM Cortex-M microcontroller class, combining real-time processing with low-power operation. This makes it suitable for battery-powered sensors, compact industrial controllers, wearable accessories, and connected equipment that must balance processing capability with energy consumption.
Key device features include 16 kB of Flash program memory, 4 kB of RAM, 17 digital I/O pins, two 16-bit timers, and a maximum operating frequency of 32 MHz. The EFM32TG family uses autonomous peripherals and energy-management modes to reduce activity in duty-cycled systems. According to the manufacturer datasheet, the family can consume as little as 0.6 µA in Stop mode and 150 µA/MHz in Run mode, supporting designs in which the processor remains idle during extended intervals.
The EFM32TG110F16-D-QFN24 is built around the ARM Cortex-M3 processor and supports two-wire Serial Wire Debug. A separate one-wire Serial Wire Viewer interface can provide profiling information, data trace, and software-generated messages. These debugging resources make it possible to inspect low-power behavior without requiring a full high-pin-count debug interface, while the 32 MHz clock rate supports responsive control and communication tasks.
Typical applications include low-power sensor nodes, building controls, compact industrial automation modules, battery-operated accessories, and embedded IoT products. The device is particularly suitable when a design needs more processing capability than an 8-bit controller but does not require the memory or I/O capacity of a larger application processor.
PCB design should preserve the exposed-pad thermal and electrical requirements of the 24-QFN package, place decoupling capacitors close to the supply pins, and provide clean routing for the Serial Wire Debug interface. Confirm the exact pin assignments and exposed-pad connection in the manufacturer pinout table before laying out a new board.
This product record combines the manufacturer specifications, package information, memory resources, low-power characteristics, and engineering guidance needed to evaluate the EFM32TG110F16-D-QFN24 for compact, low-power embedded designs.
ドロップイン代替品: EFM32TG110F16-D-QFN24 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EFM32TG110F16-D-QFN24 (同一形状・フットプリント) — 相違点: Flash Memory, Package, Debug Interface, Timers, Architecture.
EFM32TG108F16-QFN24
✅ ドロップイン価格はお問い合わせください
データシートを見る →EFM32TG110F32-D-QFN24
✅ ドロップイン価格はお問い合わせください
データシートを見る →EFM32TG108F8-D-QFN24R
✅ ドロップイン価格はお問い合わせください
データシートを見る →EFM32TG108F4-D-QFN24R
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →EFM32TG108F16-QFN24
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →EFM32TG110F16-D-QFN24 最大定格&電気的特性
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 16 kB |
| RAM | 4 kB |
| Digital I/O Pins | 17 |
| Timers | 2 x 16-bit timers |
| 電源電圧 | 2.5 V or 3.3 V |
| パッケージ | 24-QFN (5 mm x 5 mm) |
| Processor Core | ARM Cortex-M3 |
| Architecture | 32-bit RISC |
| Stop Mode Current | 0.6 µA |
| Run Mode Current | 150 µA/MHz |
| Debug Interface | 2-pin Serial Wire Debug |
| Trace Interface | 1-wire Serial Wire Viewer |
| 実装タイプ | Surface mount |
EFM32TG110F16-D-QFN24 24-qfn (5 mm x 5 mm) ピン配置ガイド
EFM32TG110F16-D-QFN24 (24-qfn (5 mm x 5 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: EFM32TG110F16-D-QFN24.
詳細は データシート をご参照ください。
主な用途
EFM32TG110F16-D-QFN24 の用途: 6 件s: Battery-Powered IoT Sensor Node, Industrial Sensor Interface, Wearable Accessory Controller, Building Control Module, Compact Power-Control Module, Battery-Powered Remote Control.
Battery-Powered IoT Sensor Node
The EFM32TG110F16-D-QFN24 fits compact sensor nodes that periodically measure an environmental or physical quantity, process the result, and return to a low-power state. Its 32 MHz ARM Cortex-M3 core provides responsive control and communication handling, while 16 kB Flash and 4 kB RAM support a focused firmware image. The EFM32TG family's 0.6 µA Stop-mode consumption and 150 µA/MHz Run-mode consumption are particularly useful when the duty cycle is dominated by idle time. Designers should use the manufacturer sleep-mode guidance, retain state only when necessary, and select peripherals that can operate without keeping the processor active.
おすすめ
Industrial Sensor Interface
The EFM32TG110F16-D-QFN24 can supervise a compact industrial sensor interface where a 3.3 V rail, modest logic memory, and deterministic low-power behavior are required. Its 17 digital I/O pins and two 16-bit timers support digital sensors, discrete inputs, timing functions, and status indication without requiring a larger application processor. The 32 MHz Cortex-M3 core can sample, filter, and format data while the EFM32TG energy-management architecture limits active time between measurements. Firmware must remain within 16 kB of Flash and 4 kB of RAM, so protocol-heavy tasks should use the smallest practical stack.
おすすめ
Wearable Accessory Controller
The EFM32TG110F16-D-QFN24 is appropriate for compact wearable accessories that coordinate simple user inputs, haptic or indicator control, and a low-rate wireless interface. The 24-QFN package limits board area, and the 32 MHz ARM Cortex-M3 core provides more headroom than an 8-bit controller while consuming only 150 µA/MHz in Run mode according to the manufacturer family datasheet. Use the 4 kB RAM carefully for radio buffering and keep application code within the 16 kB Flash region. Power sequencing and the exposed-pad layout should be checked against the package documentation before a dense wearable PCB is released.
おすすめ
Building Control Module
The EFM32TG110F16-D-QFN24 can serve as the controller in a small building-control node that reads environmental inputs, operates timers, controls a relay or actuator interface, and reports status over a low-speed link. Two 16-bit timers provide dedicated timing resources, while 17 digital I/O pins offer enough mixed-signal digital connectivity for switches, alarm inputs, and indicators. Its 2.5 V or 3.3 V operating class fits conventional embedded control rails. Because the device has 16 kB Flash and 4 kB RAM, firmware should isolate timing-critical functions from optional communications features to preserve scheduling performance.
おすすめ
Compact Power-Control Module
The EFM32TG110F16-D-QFN24 is useful in compact power-control modules that supervise load state, monitor a digital signal, and coordinate energy-saving behavior. Its 32 MHz Cortex-M3 core can execute control logic without a higher-power application processor, and the EFM32TG family's Stop-mode current of 0.6 µA supports designs that spend substantial time idle. The 17 I/O pins can handle digital enables, status inputs, and fault signals, while two 16-bit timers support periodic sampling or timing functions. The 16 kB Flash limit requires disciplined code sizing, particularly if the module also stores diagnostic histories.
おすすめ
Battery-Powered Remote Control
The EFM32TG110F16-D-QFN24 fits remote controls and compact handheld accessories that decode user commands, drive indicators, and sleep between interactions. Its 32 MHz ARM Cortex-M3 core provides quick response for button handling and communication framing, while low-power modes help reduce consumption during long inactivity. The 24-QFN footprint supports dense boards, and 17 digital I/O pins are practical for buttons, LED indicators, and interface signals. Firmware should exploit the manufacturer's wake-up mechanisms and avoid polling peripherals continuously, because active processing consumes 150 µA/MHz in the stated Run-mode operating condition.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EFM32TG110F16-D-QFN24 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EFM32TG108F16-QFN24 | EFM32TG110F32-D-QFN24 | EFM32TG108F8-D-QFN24R | EFM32TG108F4-D-QFN24R | EFM32TG108F16-QFN24 |
|---|---|---|---|---|---|---|
| Package | 24-QFN (5 mm x 5 mm) | 24-QFN | 24-QFN (5 mm x 5 mm) | 24-QFN | 24-QFN | 24-QFN |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 16 kB | 16 kB | 32 kB | 8 kB | 4 kB | 16 kB |
| Family | EFM32TG110 Tiny Gecko | EFM32TG108 Tiny Gecko | EFM32TG110 Tiny Gecko | EFM32TG108 Tiny Gecko | EFM32TG108 Tiny Gecko | EFM32TG108 Tiny Gecko |
主な差別化要因
- Balanced 16 kB Flash configuration within the Tiny Gecko family (vs EFM32TG110F32-D-QFN24)
- Closer functional alignment with the same-memory TG108 option (vs EFM32TG108F16-QFN24)
- Substantially greater code space than the smallest 24-QFN family candidates (vs EFM32TG108F4-D-QFN24R)
設計ノート
Use the manufacturer QFN land pattern and exposed-pad geometry for the 24-QFN package rather than treating the body outline as the solder footprint. Place input and output decoupling capacitors close to their associated supply pins, provide a continuous ground plane, and minimize loop area through the exposed pad. Confirm pin-1 orientation against the package drawing before placing the device.
Keep the two Serial Wire Debug signals and the 1-wire Serial Wire Viewer connection short and away from switching nodes, crystal routing, and high-current paths. The manufacturer documentation identifies both as debugging resources, so preserving predictable access avoids later board rewiring. If these signals share a connector, route them as a controlled group and ground-reference them to the MCU ground plane.
The target operates from a 2.5 V or 3.3 V supply, but the exact regulator output tolerance and transient requirement must still match the Silicon Labs electrical limits. Decouple each relevant supply rail near the device and verify startup behavior in the selected low-power mode. Do not assume the 0.6 µA Stop-mode figure includes external pull-ups, sensor leakage, or radio-module consumption.
Do not substitute a 32 kB-Flash or 8 kB-Flash family member without reviewing the linker map, bootloader, vector table, and application firmware. A larger Flash device changes the memory map, while a smaller device can overflow code or data sections. Also verify that the exact -D-QFN24 ordering suffix matches the intended temperature, grade, and production requirements before releasing a purchase order.
コンプライアンス情報
The manufacturer documentation excerpt does not explicitly state the requested compliance statuses. The automotive qualification status for the exact -D-QFN24 ordering suffix also requires confirmation.