EFM32TG110F16-D-QFN24 - 32MHz Cortex-M3 16KB MCU | Silicon Labs
Référence : EFM32TG110F16-D-QFN24 ✗ Fin de vieEFM32TG110F16-D-QFN24 Présentation
A microcontroller is a programmable semiconductor that integrates a processor core, memory, digital interfaces, timers, and analog peripherals onto one device. In the system hierarchy, the EFM32TG110F16-D-QFN24 belongs to the ARM Cortex-M microcontroller class, combining real-time processing with low-power operation. This makes it suitable for battery-powered sensors, compact industrial controllers, wearable accessories, and connected equipment that must balance processing capability with energy consumption.
Key device features include 16 kB of Flash program memory, 4 kB of RAM, 17 digital I/O pins, two 16-bit timers, and a maximum operating frequency of 32 MHz. The EFM32TG family uses autonomous peripherals and energy-management modes to reduce activity in duty-cycled systems. According to the manufacturer datasheet, the family can consume as little as 0.6 µA in Stop mode and 150 µA/MHz in Run mode, supporting designs in which the processor remains idle during extended intervals.
The EFM32TG110F16-D-QFN24 is built around the ARM Cortex-M3 processor and supports two-wire Serial Wire Debug. A separate one-wire Serial Wire Viewer interface can provide profiling information, data trace, and software-generated messages. These debugging resources make it possible to inspect low-power behavior without requiring a full high-pin-count debug interface, while the 32 MHz clock rate supports responsive control and communication tasks.
Typical applications include low-power sensor nodes, building controls, compact industrial automation modules, battery-operated accessories, and embedded IoT products. The device is particularly suitable when a design needs more processing capability than an 8-bit controller but does not require the memory or I/O capacity of a larger application processor.
PCB design should preserve the exposed-pad thermal and electrical requirements of the 24-QFN package, place decoupling capacitors close to the supply pins, and provide clean routing for the Serial Wire Debug interface. Confirm the exact pin assignments and exposed-pad connection in the manufacturer pinout table before laying out a new board.
This product record combines the manufacturer specifications, package information, memory resources, low-power characteristics, and engineering guidance needed to evaluate the EFM32TG110F16-D-QFN24 for compact, low-power embedded designs.
Alternatives de remplacement direct pour EFM32TG110F16-D-QFN24 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec EFM32TG110F16-D-QFN24 (même facteur de forme et même empreinte) — différant par Flash Memory, Package, Debug Interface, Timers, Architecture.
EFM32TG108F16-QFN24
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →EFM32TG110F32-D-QFN24
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →EFM32TG108F8-D-QFN24R
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →EFM32TG108F4-D-QFN24R
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →EFM32TG108F16-QFN24
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →EFM32TG110F16-D-QFN24 Valeurs maximales et caractéristiques électriques
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 16 kB |
| RAM | 4 kB |
| Digital I/O Pins | 17 |
| Timers | 2 x 16-bit timers |
| Tension d'alimentation | 2.5 V or 3.3 V |
| Boîtier | 24-QFN (5 mm x 5 mm) |
| Processor Core | ARM Cortex-M3 |
| Architecture | 32-bit RISC |
| Stop Mode Current | 0.6 µA |
| Run Mode Current | 150 µA/MHz |
| Debug Interface | 2-pin Serial Wire Debug |
| Trace Interface | 1-wire Serial Wire Viewer |
| Type de montage | Surface mount |
Guide de configuration des broches du EFM32TG110F16-D-QFN24 24-qfn (5 mm x 5 mm)
Configuration des broches du EFM32TG110F16-D-QFN24 (boîtier 24-qfn (5 mm x 5 mm)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour EFM32TG110F16-D-QFN24.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
EFM32TG110F16-D-QFN24 convient pour 6 applications: Battery-Powered IoT Sensor Node, Industrial Sensor Interface, Wearable Accessory Controller, Building Control Module, Compact Power-Control Module, Battery-Powered Remote Control.
Battery-Powered IoT Sensor Node
The EFM32TG110F16-D-QFN24 fits compact sensor nodes that periodically measure an environmental or physical quantity, process the result, and return to a low-power state. Its 32 MHz ARM Cortex-M3 core provides responsive control and communication handling, while 16 kB Flash and 4 kB RAM support a focused firmware image. The EFM32TG family's 0.6 µA Stop-mode consumption and 150 µA/MHz Run-mode consumption are particularly useful when the duty cycle is dominated by idle time. Designers should use the manufacturer sleep-mode guidance, retain state only when necessary, and select peripherals that can operate without keeping the processor active.
Recommandé
Industrial Sensor Interface
The EFM32TG110F16-D-QFN24 can supervise a compact industrial sensor interface where a 3.3 V rail, modest logic memory, and deterministic low-power behavior are required. Its 17 digital I/O pins and two 16-bit timers support digital sensors, discrete inputs, timing functions, and status indication without requiring a larger application processor. The 32 MHz Cortex-M3 core can sample, filter, and format data while the EFM32TG energy-management architecture limits active time between measurements. Firmware must remain within 16 kB of Flash and 4 kB of RAM, so protocol-heavy tasks should use the smallest practical stack.
Recommandé
Wearable Accessory Controller
The EFM32TG110F16-D-QFN24 is appropriate for compact wearable accessories that coordinate simple user inputs, haptic or indicator control, and a low-rate wireless interface. The 24-QFN package limits board area, and the 32 MHz ARM Cortex-M3 core provides more headroom than an 8-bit controller while consuming only 150 µA/MHz in Run mode according to the manufacturer family datasheet. Use the 4 kB RAM carefully for radio buffering and keep application code within the 16 kB Flash region. Power sequencing and the exposed-pad layout should be checked against the package documentation before a dense wearable PCB is released.
Recommandé
Building Control Module
The EFM32TG110F16-D-QFN24 can serve as the controller in a small building-control node that reads environmental inputs, operates timers, controls a relay or actuator interface, and reports status over a low-speed link. Two 16-bit timers provide dedicated timing resources, while 17 digital I/O pins offer enough mixed-signal digital connectivity for switches, alarm inputs, and indicators. Its 2.5 V or 3.3 V operating class fits conventional embedded control rails. Because the device has 16 kB Flash and 4 kB RAM, firmware should isolate timing-critical functions from optional communications features to preserve scheduling performance.
Recommandé
Compact Power-Control Module
The EFM32TG110F16-D-QFN24 is useful in compact power-control modules that supervise load state, monitor a digital signal, and coordinate energy-saving behavior. Its 32 MHz Cortex-M3 core can execute control logic without a higher-power application processor, and the EFM32TG family's Stop-mode current of 0.6 µA supports designs that spend substantial time idle. The 17 I/O pins can handle digital enables, status inputs, and fault signals, while two 16-bit timers support periodic sampling or timing functions. The 16 kB Flash limit requires disciplined code sizing, particularly if the module also stores diagnostic histories.
Recommandé
Battery-Powered Remote Control
The EFM32TG110F16-D-QFN24 fits remote controls and compact handheld accessories that decode user commands, drive indicators, and sleep between interactions. Its 32 MHz ARM Cortex-M3 core provides quick response for button handling and communication framing, while low-power modes help reduce consumption during long inactivity. The 24-QFN footprint supports dense boards, and 17 digital I/O pins are practical for buttons, LED indicators, and interface signals. Firmware should exploit the manufacturer's wake-up mechanisms and avoid polling peripherals continuously, because active processing consumes 150 µA/MHz in the stated Run-mode operating condition.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour EFM32TG110F16-D-QFN24 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | EFM32TG108F16-QFN24 | EFM32TG110F32-D-QFN24 | EFM32TG108F8-D-QFN24R | EFM32TG108F4-D-QFN24R | EFM32TG108F16-QFN24 |
|---|---|---|---|---|---|---|
| Package | 24-QFN (5 mm x 5 mm) | 24-QFN | 24-QFN (5 mm x 5 mm) | 24-QFN | 24-QFN | 24-QFN |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 16 kB | 16 kB | 32 kB | 8 kB | 4 kB | 16 kB |
| Family | EFM32TG110 Tiny Gecko | EFM32TG108 Tiny Gecko | EFM32TG110 Tiny Gecko | EFM32TG108 Tiny Gecko | EFM32TG108 Tiny Gecko | EFM32TG108 Tiny Gecko |
Principaux différenciateurs
- Balanced 16 kB Flash configuration within the Tiny Gecko family (vs EFM32TG110F32-D-QFN24)
- Closer functional alignment with the same-memory TG108 option (vs EFM32TG108F16-QFN24)
- Substantially greater code space than the smallest 24-QFN family candidates (vs EFM32TG108F4-D-QFN24R)
Notes de conception
Use the manufacturer QFN land pattern and exposed-pad geometry for the 24-QFN package rather than treating the body outline as the solder footprint. Place input and output decoupling capacitors close to their associated supply pins, provide a continuous ground plane, and minimize loop area through the exposed pad. Confirm pin-1 orientation against the package drawing before placing the device.
Keep the two Serial Wire Debug signals and the 1-wire Serial Wire Viewer connection short and away from switching nodes, crystal routing, and high-current paths. The manufacturer documentation identifies both as debugging resources, so preserving predictable access avoids later board rewiring. If these signals share a connector, route them as a controlled group and ground-reference them to the MCU ground plane.
The target operates from a 2.5 V or 3.3 V supply, but the exact regulator output tolerance and transient requirement must still match the Silicon Labs electrical limits. Decouple each relevant supply rail near the device and verify startup behavior in the selected low-power mode. Do not assume the 0.6 µA Stop-mode figure includes external pull-ups, sensor leakage, or radio-module consumption.
Do not substitute a 32 kB-Flash or 8 kB-Flash family member without reviewing the linker map, bootloader, vector table, and application firmware. A larger Flash device changes the memory map, while a smaller device can overflow code or data sections. Also verify that the exact -D-QFN24 ordering suffix matches the intended temperature, grade, and production requirements before releasing a purchase order.
Informations de conformité
The manufacturer documentation excerpt does not explicitly state the requested compliance statuses. The automotive qualification status for the exact -D-QFN24 ordering suffix also requires confirmation.