EFM32TG210F32-D-QFN32 - 32MHz Cortex-M3 MCU | Silicon Labs
部品番号: EFM32TG210F32-D-QFN32 ✓ 生産中EFM32TG210F32-D-QFN32 概要
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals such as timers, serial interfaces, analog functions, and GPIO on one device. The EFM32TG series belongs to the 32-bit MCU hierarchy and uses the ARM Cortex-M3 RISC architecture. This class of device provides greater processing capacity than an 8- or 16-bit MCU while supporting low-power operation for battery-operated equipment.
The EFM32TG210F32-D-QFN32 includes 32 KB of Flash for firmware and 4 KB of SRAM for working data. Its CPU operates at up to 32 MHz, and the device provides two 16-bit timers and 24 digital I/O pins. The Tiny Gecko platform also features autonomous peripheral operation, allowing timer and communication activities to continue with limited processor intervention. Run-mode consumption is specified at 150 microamperes per megahertz, while Stop mode can reach 0.6 microamperes.
The ARM Cortex-M3 core uses a 32-bit RISC instruction set and can achieve as much as 1.25 Dhrystone MIPS per megahertz. A memory protection unit supports as many as eight memory segments, and the Wake-up Interrupt Controller handles events that occur while the processor is asleep. These features allow responsive interrupt-driven designs without keeping the CPU continuously active.
Typical applications include wearable sensors, compact industrial nodes, battery-powered remote controls, connected IoT equipment, and portable measurement instruments. The 32 MHz processing rate is suitable for protocol handling, state-machine control, data acquisition, and low-to-moderate-bandwidth communications. The 24 GPIO pins also permit direct connection of switches, indicators, sensors, and actuators.
PCB design should preserve the exposed-pad thermal and electrical requirements of the QFN package. Place decoupling capacitors close to the power pins, connect the exposed pad to the appropriate ground plane, and follow the manufacturer pin description table when assigning tracks. Confirm the selected package dimensions and exposed-pad treatment against the manufacturer datasheet before fabrication.
This product page combines the manufacturer specifications, package information, application guidance, and practical design considerations in one engineering reference. It also distinguishes pin-compatible family alternatives while identifying where package, memory, or peripheral differences require design review.
ドロップイン代替品: EFM32TG210F32-D-QFN32 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
EFM32TG211F32-QFN32
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
EFM32TG212F32-QFN32
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
EFM32TG210F32-D-QFN32 最大定格&電気的特性
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Processor Core | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 32 KB |
| RAM | 4 KB |
| Digital I/O Pins | 24 |
| Timers | 2 x 16-bit timers |
| Architecture | 32-bit RISC |
| Dhrystone Performance | Up to 1.25 MIPS/MHz |
| Memory Protection | Up to 8 memory segments |
| Run-Mode Current | 150 microamperes/MHz |
| Stop-Mode Current | 0.6 microamperes |
| 電源電圧 | 2.5 V or 3.3 V |
| パッケージ | 32-pin QFN, 6 x 6 mm |
| 実装タイプ | Surface mount |
| Packaging | Tray |
EFM32TG210F32-D-QFN32 32-pin qfn, 6 x 6 mm ピン配置ガイド
EFM32TG210F32-D-QFN32 (32-pin qfn, 6 x 6 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: EFM32TG210F32-D-QFN32.
詳細は データシート をご参照ください。
主な用途
EFM32TG210F32-D-QFN32 の用途: 6 件s: Battery-Powered IoT Sensor Nodes, Portable Medical Sensor Interfaces, Industrial Monitoring and Control, Wearable Device Controllers, Smart Home Sensor Hubs, Portable Measurement Instruments.
Battery-Powered IoT Sensor Nodes
The EFM32TG210F32-D-QFN32 fits compact wireless sensor nodes that spend most of their operating life in low-power states. Its 0.6-microampere Stop mode allows the processor to idle between measurements, while the 32 MHz Cortex-M3 core can handle sensor conditioning, packet preparation, and event processing when awake. Run-mode consumption of 150 microamperes per megahertz also supports predictable active-current planning. The 24 GPIO pins can connect sensors, indicators, and configuration switches without requiring a separate I/O expander. Firmware should use the Wake-up Interrupt Controller to wake the MCU for scheduled sampling and peripheral events, reducing unnecessary active time.
おすすめ
Portable Medical Sensor Interfaces
The EFM32TG210F32-D-QFN32 can serve as the control MCU in a portable medical sensor interface when the design requires deterministic peripheral timing and low standby consumption. Its two 16-bit timers support periodic sampling, debouncing, or actuator timing, while 24 GPIO pins provide direct connections to sensors, status indicators, and user controls. The 32-bit Cortex-M3 core also provides enough arithmetic capacity for local filtering and protocol handling. Because this is a general-purpose MCU rather than a medical-qualified device, the complete signal chain still requires suitable isolation, protection, analog front-end design, and applicable clinical validation.
おすすめ
Industrial Monitoring and Control
The EFM32TG210F32-D-QFN32 is appropriate for small industrial monitoring modules that combine digital inputs, status feedback, and local computation. Its 24 GPIO pins can operate digital sensors and discrete outputs, and the two 16-bit timers are useful for pulse counting, sampling intervals, and motor or actuator timing. Operating at up to 32 MHz supports state-machine execution, logging, and communication protocol handling. The low-power characteristics also benefit remote equipment that operates intermittently. Industrial qualification requirements must be checked independently, and the PCB should include appropriate protection, transient immunity, and environmental isolation around field-wired interfaces.
おすすめ
Wearable Device Controllers
The EFM32TG210F32-D-QFN32 suits wearable controllers where a full-size processor would be excessive but 8-bit control is insufficient. Its 32-bit Cortex-M3 core, 32 KB Flash, and 4 KB RAM are adequate for gesture-state machines, haptic control, simple user interfaces, and short Bluetooth-class protocol handling. The 6 x 6 mm QFN-32 package preserves board area in compact products, and the 0.6-microampere Stop mode supports low-energy idle behavior. Battery life still depends on radio activity, sensor duty cycle, regulator efficiency, and board leakage, so the MCU specification should be evaluated as part of the complete power budget.
おすすめ
Smart Home Sensor Hubs
The EFM32TG210F32-D-QFN32 can act as a local smart-home sensor hub for door contacts, occupancy inputs, temperature sensing, and actuator status. Its 24 GPIO pins allow multiple digital inputs to be connected directly, and the two 16-bit timers can manage debounce intervals, periodic polling, or indicator timing. At up to 32 MHz, the Cortex-M3 core is capable of protocol translation and local event logic while the 150-microamperes-per-megahertz Run specification supports predictable active power. A complete hub design must also include a suitable radio, sensor interfaces, firmware update strategy, and suitable enclosure and environmental protection.
おすすめ
Portable Measurement Instruments
The EFM32TG210F32-D-QFN32 provides a compact control platform for portable measurement instruments requiring timers, digital I/O, local data processing, and low standby demand. The 32-bit core at 32 MHz can execute instrument state logic, calibration calculations, and data-transfer routines, while the two 16-bit timers support precise sampling intervals and reference-clock functions. The QFN-32 package leaves board area available for analog circuitry, display interfaces, and isolated communication hardware. Analog measurement accuracy is not determined by the MCU alone; designers should pair it with suitable references, converters, input protection, and calibration procedures.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EFM32TG210F32-D-QFN32 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EFM32TG211F32-QFN32 | EFM32TG212F32-QFN32 |
|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | QFN-32 (6 x 6 mm) | QFN-32 (6 x 6 mm) - same package | QFN-32 (6 x 6 mm) - same package |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB |
| RAM | 4 KB | 4 KB | 4 KB |
主な差別化要因
- Established low-power operating characteristics (vs EFM32TG211F32-QFN32)
- 32-bit processing with dedicated timer resources (vs EFM32TG212F32-QFN32)
- Pin-compatible family reuse without reducing core resources (vs EFM32TG211F32-QFN32)
設計ノート
Place input, output, and local bypass capacitors close to their associated power pins and return them to the ground plane without long loops. The QFN-32 device also uses an exposed pad, so the land pattern should preserve the manufacturer-specified pad geometry and connect the pad to the appropriate ground plane. Review pin assignments against the manufacturer pin-description table before routing because several alternate-function signals share the same GPIO pins.
The 2.5 V or 3.3 V supply requirement must remain within the electrical limits for the selected device, and the regulator should accommodate the Cortex-M3 core plus active peripherals. Use the 150-microamperes-per-megahertz Run-mode figure as a core-current planning input, then add GPIO, analog, and peripheral loads. In Stop mode, verify that external pull resistors, sensors, and communication circuits do not dominate the 0.6-microampere MCU current.
Keep high-frequency clock and debug routes short, return them to a continuous ground reference, and avoid routing them beside noisy switching nodes or unprotected field inputs. The exposed-pad connection supports thermal and electrical performance, but it does not replace correct decoupling. Use a common ground strategy suitable for the complete analog, digital, and power domains rather than splitting the ground plane without a deliberate return-current plan.
Do not treat QFN-32 package compatibility as proof of software or electrical equivalence. Confirm the alternate-function mapping, peripheral inventory, startup sequence, clock requirements, and exposed-pad connection for every proposed replacement. When moving from EFM32TG210F32-D-QFN32 to EFM32TG211F32-QFN32 or EFM32TG212F32-QFN32, recompile against the selected device headers and run peripheral, interrupt, low-power, and brownout testing.
コンプライアンス情報
Compliance and qualification attributes are not stated in the accessible product information. Verify current material and automotive qualification status with the manufacturer before production release.