EFM32TG825F16-BGA48T - 32MHz Cortex-M3 16KB MCU | Silicon Labs
部品番号: EFM32TG825F16-BGA48T ✗ 生産終了EFM32TG825F16-BGA48T 概要
A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, RAM, and peripherals into one device. The EFM32 Tiny Gecko family belongs to the embedded microcontroller hierarchy, combining an ARM Cortex-M3 processor with energy-management peripherals designed for battery-operated and always-on products. The T suffix identifies the tape-and-reel ordering configuration for the EFM32TG825F16-BGA48 device.
The device combines a 32 MHz ARM Cortex-M3 core with 16KB of flash and low-power operating features. Its supply range of 1.85 V to 3.8 V accommodates common single-cell and low-voltage rails. Energy-conscious applications can use the MCU's deep-sleep capability, power-on reset, brown-out detection, and retained RAM or CPU state. The family documentation also identifies a deep-sleep current of approximately 1.0 µA at 3 V when the RTC and 32.768 kHz oscillator are included.
The Tiny Gecko architecture is intended for low-energy embedded control. Its 32-bit Cortex-M3 instruction set provides substantially greater arithmetic capability than an 8-bit controller while retaining a compact, deterministic embedded footprint. Integrated low-power peripherals allow firmware to spend more time in energy-saving states and return to active operation without requiring the application to recreate volatile state after every sleep cycle.
Typical uses include battery-powered sensor nodes, industrial condition-monitoring devices, compact energy-harvesting products, wearable accessories, and portable measurement equipment. The 16KB program memory suits applications with focused control logic, protocol handling, and modest local data processing. Firmware capacity should be checked against the final application code, protocol stacks, bootloader, and update mechanism.
Board design must follow the manufacturer package drawing and pin-description table, particularly for exposed-pad, ground-ball, and power-routing requirements. Place decoupling capacitors close to the supply pins, route sensitive inputs away from switching nodes, and provide a clean low-impedance ground reference. Confirm BGA assembly capability and ball-pitch constraints with the selected PCB manufacturer before committing the layout.
This product page combines the manufacturer's device characteristics with practical selection guidance, same-family drop-in alternatives, package information, power-budget considerations, and engineering-oriented comparisons. These resources help teams assess package complexity, memory requirements, lifecycle constraints, and low-power suitability before integrating the EFM32TG825F16-BGA48T into a new PCB.
ドロップイン代替品: EFM32TG825F16-BGA48T — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EFM32TG825F16-BGA48T (同一形状・フットプリント) — 相違点: Flash Memory, Package, RAM, Product Type, Supply Voltage Range.
EFM32TG825F8-BGA48T
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →EFM32TG225F32-BGA48T
✅ ドロップイン📋 参考代替品(カタログ未掲載)
EFM32TG225F8-D-BGA48R
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →EFM32TG825F32-BGA48T
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →EFM32TG825F16-BGA48T 最大定格&電気的特性
| Product Type | 32-bit embedded microcontroller |
| Series | EFM32 Tiny Gecko |
| Processor Core | ARM Cortex-M3 |
| CPU Speed | 32 MHz |
| Flash Memory | 16KB (16K x 8) |
| Supply Voltage Range | 1.85 V to 3.8 V |
| Deep-Sleep Current | Approximately 1.0 µA at 3 V |
| Deep-Sleep Configuration | Includes RTC with 32.768 kHz oscillator |
| Power Management Features | Output state retention, wake-up from Shutoff Mode, RAM retention, and CPU retention |
| Reset Features | Power-on reset and brown-out detector |
| Architecture | Single-core |
| パッケージ | 48-BGA (4x4 mm) |
| 実装タイプ | Surface mount |
| Ordering Suffix | T tape-and-reel configuration |
EFM32TG825F16-BGA48T 48-bga (4x4 mm) ピン配置ガイド
EFM32TG825F16-BGA48T (48-bga (4x4 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: EFM32TG825F16-BGA48T.
詳細は データシート をご参照ください。
主な用途
EFM32TG825F16-BGA48T の用途: 6 件s: Battery-Powered Environmental Sensor Node, Industrial Condition Monitoring, Wearable Accessory Controller, Portable Medical Sensor Interface, Smart Home Sensor Hub, Energy-Harvesting Controller.
Battery-Powered Environmental Sensor Node
The EFM32TG825F16-BGA48T fits compact environmental sensors that periodically measure temperature, humidity, or air quality and then return to a low-power state. Its 32 MHz ARM Cortex-M3 core provides enough processing capability for local filtering and sensor compensation within a 16KB flash budget. The approximately 1.0 µA deep-sleep current at 3 V, together with RAM and CPU retention, can reduce the energy cost of inactive periods. Use a duty-cycled sampling strategy, retain calibration data in nonvolatile memory, and activate the radio only after measurement completion to maximize battery life.
おすすめ
Industrial Condition Monitoring
The EFM32TG825F16-BGA48T is suitable for factory equipment that monitors vibration, temperature, or machine state while avoiding a large wired controller. Its 32 MHz Cortex-M3 core can execute control logic, threshold checks, and a compact industrial communication routine, while the 48-BGA package limits board area. The device's 1.85 V to 3.8 V operating range supports regulated sensor and communication rails. For industrial deployments, design the power supply for the full temperature range, include brown-out monitoring, and isolate high-energy motor or relay switching from sensitive sensor inputs.
おすすめ
Wearable Accessory Controller
The EFM32TG825F16-BGA48T can serve as the central controller in a compact wearable accessory where the application performs simple button, motion, or haptic logic rather than intensive data processing. Its 48-BGA 4x4 mm package supports dense board layouts, and the Cortex-M3 architecture provides 32-bit processing with a compact software footprint. The deep-sleep state, RTC support, and state-retention features are useful between user interactions. Care must be taken to match the MCU and radio supplies, place decoupling close to the device, and keep antenna and sensor routing away from noisy power paths.
おすすめ
Portable Medical Sensor Interface
The EFM32TG825F16-BGA48T is appropriate for a portable sensing accessory that handles acquisition control, signal conditioning supervision, and low-power data buffering. Its 32 MHz Cortex-M3 core supports deterministic digital filtering and device-state management, while 16KB of flash can hold a focused firmware image when code size is carefully managed. The low-power shutdown and wake-up behavior can support a duty-cycled acquisition system. Use the exact pin assignments, medical-device risk controls, calibration strategy, and isolation requirements applicable to the finished product; the MCU qualification status itself is not established.
おすすめ
Smart Home Sensor Hub
The EFM32TG825F16-BGA48T can manage a small collection of low-power sensors in a smart-home endpoint, coordinating measurements and communicating status over a compact serial link. The 32 MHz Cortex-M3 core handles protocol framing and local logic, while the 48-BGA footprint supports dense multi-sensor boards. Its deep-sleep current of approximately 1.0 µA at 3 V helps when the endpoint spends most of its time inactive. Choose an appropriate communication companion, maintain deterministic timing for sensor updates, and include brown-out recovery so intermittent power faults do not corrupt device configuration.
おすすめ
Energy-Harvesting Controller
The EFM32TG825F16-BGA48T is suited to energy-harvesting endpoints that store limited harvested energy and operate only when sufficient voltage is available. Its 1.85 V to 3.8 V supply range, low-power modes, and approximately 1.0 µA deep-sleep current help reduce continuous energy demand. The 16KB flash allocation is adequate for focused energy-management, sampling, and state-machine firmware when code size is controlled. A practical design should measure the real harvester output, regulate it for the MCU rail, account for capacitor leakage, and prevent writes to nonvolatile memory from occurring more frequently than the harvested energy budget can support.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EFM32TG825F16-BGA48T — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EFM32TG825F8-BGA48T | EFM32TG225F32-BGA48T | EFM32TG225F8-D-BGA48R | EFM32TG825F32-BGA48T |
|---|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 48-BGA (4x4 mm) | 48-BGA (4x4 mm) | 48-BGA (4x4 mm) | 48-BGA (4x4 mm) | 48-BGA (4x4 mm) |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 |
| CPU Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 16KB | 8KB | 32KB | 8KB | 32KB |
| Core Architecture | Tiny Gecko | Tiny Gecko | Tiny Gecko | Tiny Gecko | Tiny Gecko |
| Low-Power Features | Output-state retention, wake-up from Shutoff Mode, RAM retention, CPU retention, RTC, power-on reset, and brown-out detection | Tiny Gecko low-power feature set | Tiny Gecko low-power feature set | Tiny Gecko low-power feature set | Tiny Gecko low-power feature set |
主な差別化要因
- Balanced memory configuration within the Tiny Gecko family (vs EFM32TG825F8-BGA48T)
- Lower memory footprint than the 32KB family option (vs EFM32TG225F32-BGA48T)
- Defined low-power behavior for duty-cycled products (vs EFM32TG225F8-D-BGA48R)
設計ノート
Use the manufacturer BGA48 land pattern and pin-description table rather than a generic 48-ball library. Place all decoupling capacitors directly between the appropriate supply and ground balls with very short traces. Confirm the board's ball-pitch support, solder-mask and paste design, via-in-pad policy, and assembly capability before release because the 4x4 mm BGA package is sensitive to coplanarity and reflow-profile variation.
Estimated: a 3.0 V supply operating at 1.85 V with an active-state current of 10 mA would dissipate approximately 11.5 mW in the MCU, calculated as (3.0 V - 1.85 V) × 10 mA. This example excludes board-level regulator losses and does not represent a datasheet operating point. Select the supply rail and regulator according to peak active current, wake-up demand, peripheral load, and the battery's usable voltage range.
Keep the 32.768 kHz crystal and its supporting components close to the designated oscillator balls, with short, symmetrical traces and a quiet ground return. Avoid routing the RTC oscillator beneath or beside noisy switching converters and high-current LED paths. Follow the manufacturer's recommended load capacitance and grounding arrangement; incorrect PCB capacitance can change startup behavior, clock accuracy, and power consumption.
Do not treat a package-compatible family alternative as firmware-compatible. Flash size, peripheral availability, interrupt mapping, startup code, and device-specific configuration can differ even when the processor class and BGA outline match. Build each replacement with the appropriate Silicon Labs device headers, verify the complete pin table, run boundary tests at 1.85 V and 3.8 V, and validate low-power wake-up behavior before production use.
コンプライアンス情報
Compliance attributes were not identified in the available manufacturer or distributor records. Confirm the exact orderable MPN with the manufacturer compliance documentation before production release.