HMCAD1512 - 8-bit Dual 250MSPS ADC E-Band | Analog Devices
部品番号: HMCAD1512 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $38.5 | $38.50 |
| 10 | $34.65 | $346.50 |
| 100 | $30.8 | $3,080.00 |
| 500 | $27.5 | $13,750.00 |
| 1,000 | $24.2 | $24,200.00 |
HMCAD1512 概要
An ADC (analog-to-digital converter) is an integrated circuit that converts continuous analog signals into discrete digital codes for digital signal processing. The HMCAD1512 belongs to the successive-approximation / pipelined ADC category, positioned hierarchically as: pipelined ADC -> high-speed ADC -> data converter -> signal chain IC -> semiconductor. Time-interleaved ADCs like this one reach higher sampling rates by multiplexing multiple lower-rate ADC cores, trading channel count and calibration complexity for speed.
Key features include 250MSPS per channel (500MSPS in interleaved mode), 48 dBFS signal-to-noise ratio at 100 MHz input, 1.5 GHz analog input bandwidth, LVDS/CMOS-compatible digital outputs, and an SPI-programmable gain and offset. The integrated cross-point switch routes either input to either ADC channel without external muxes. The 48-QFN package provides a compact footprint with an exposed thermal pad (theta_JA approximately 30 C/W) that supports efficient heat extraction at full-sample-rate operation.
The HMCAD1512 uses a multi-stage pipelined architecture per channel with on-chip calibration to correct inter-channel gain and timing mismatches introduced by the interleaver. Front-end track-and-hold amplifiers present a 100-ohm differential input impedance and include a coarse/fine gain control block that adjusts full-scale range from 500 mVpp to 1 Vpp differential without external attenuators, simplifying front-panel or AGC loop designs.
Typical applications include E-band microwave radio links, radar digitizers, digital oscilloscopes, communications test equipment, and high-speed data acquisition. The dual-channel architecture also suits I/Q baseband sampling in direct-conversion transceivers and MIMO radar receivers where two synchronized streams are needed.
When designing with this device, allocate at least four PCB layers for the digital LVDS outputs and route 100-ohm differential pairs with controlled impedance to the FPGA/ASIC. Provide a clean 1.8V analog supply and a separate 1.8V digital supply, and decouple both with 10 uF bulk plus 100 nF ceramic capacitors placed within 2 mm of each supply pin.
This page synthesizes distributor pricing, drop-in pin-compatible alternatives (HMCAD1511, HMCAD1520, HMCAD1041), and practical design guidance not available from a single manufacturer datasheet.
ドロップイン代替品: HMCAD1512 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: HMCAD1512 （同一形状・フットプリント） — 相違点: Architecture, Number of Channels, Package, Resolution.
クイック比較ツール — 並列比較する代替部品を選択:
HMCAD1511
✅ ドロップイン📋 参考代替品（カタログ未掲載）
HMCAD1520
✅ ドロップイン📋 参考代替品（カタログ未掲載）
HMCAD1041LP4E
✅ ドロップイン📋 参考代替品（カタログ未掲載）
HMCAD1050-80
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$14.95 / 個
データシートを見る →HMCAD1512 最大定格＆電気的特性
| Manufacturer | Analog Devices (formerly Hittite Microwave) |
| Part Number | HMCAD1512 |
| Converter Type | Time-interleaved pipelined ADC |
| 分解能 | 8 bit |
| Number of Channels | 2 (with cross-point switch) |
| Sampling Rate (per channel) | 250 MSPS |
| Sampling Rate (interleaved) | 500 MSPS |
| Input Configuration | 2 differential inputs selectable via cross-point switch |
| Input Bandwidth | 1.5 GHz |
| Output Interface | LVDS / Serial LVDS / CMOS |
| Analog Supply | 1.8 V |
| Digital Supply | 1.8 V |
| Input Impedance | 100 ohm differential |
| Full-Scale Input Range | 500 mVpp to 1 Vpp differential (programmable) |
| パッケージ | 48-QFN (7x7 mm, HVQCCN) with exposed pad |
| 動作温度範囲 | -40C to +85C (industrial) |
| ピン数 | 48 |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
| Architecture | Pipelined with on-chip calibration |
HMCAD1512 ピン構成
| ピン 1 | GND — Ground |
| ピン 2 | AINA_P — Channel A positive analog input |
| ピン 3 | AINA_N — Channel A negative analog input |
| ピン 4 | AINB_P — Channel B positive analog input |
| ピン 5 | AINB_N — Channel B negative analog input |
| ピン 6 | VCM — Common-mode voltage reference |
| ピン 7 | VA1V8 — 1.8 V analog supply |
| ピン 8 | GND — Ground |
| ピン 9 | VD1V8 — 1.8 V digital supply |
| ピン 10 | GND — Ground |
| ピン 11 | D0_P — LVDS data output 0 positive |
| ピン 12 | D0_N — LVDS data output 0 negative |
| ピン 13 | D1_P — LVDS data output 1 positive |
| ピン 14 | D1_N — LVDS data output 1 negative |
| ピン 15 | D2_P — LVDS data output 2 positive |
| ピン 16 | D2_N — LVDS data output 2 negative |
| ピン 17 | D3_P — LVDS data output 3 positive |
| ピン 18 | D3_N — LVDS data output 3 negative |
| ピン 19 | D4_P — LVDS data output 4 positive |
| ピン 20 | D4_N — LVDS data output 4 negative |
| ピン 21 | D5_P — LVDS data output 5 positive |
| ピン 22 | D5_N — LVDS data output 5 negative |
| ピン 23 | D6_P — LVDS data output 6 positive |
| ピン 24 | D6_N — LVDS data output 6 negative |
| ピン 25 | D7_P — LVDS data output 7 positive |
| ピン 26 | D7_N — LVDS data output 7 negative |
| ピン 27 | DCLK_P — LVDS data clock positive |
| ピン 28 | DCLK_N — LVDS data clock negative |
| ピン 29 | OR_P — Out-of-range positive |
| ピン 30 | OR_N — Out-of-range negative |
| ピン 31 | GND — Ground |
| ピン 32 | RESETn — Reset (active low) |
| ピン 33 | CSn — SPI chip select (active low) |
| ピン 34 | SCLK — SPI clock |
| ピン 35 | SDIO — SPI data IO |
| ピン 36 | SDO — SPI data out |
| ピン 37 | GND — Ground |
| ピン 38 | GND — Ground |
| ピン 39 | GND — Ground |
| ピン 40 | GND — Ground |
| ピン 41 | GND — Ground |
| ピン 42 | GND — Ground |
| ピン 43 | GND — Ground |
| ピン 44 | GND — Ground |
| ピン 45 | GND — Ground |
| ピン 46 | GND — Ground |
| ピン 47 | GND — Ground |
| ピン 48 | EPAD — Exposed thermal pad - connect to ground |
主な用途
HMCAD1512 の用途: 6 件s: E-Band Microwave Radio Digitizer, Digital Oscilloscope Front-End, Radar Receiver Digitization, Communications Test Equipment, High-Speed Data Acquisition, Direct-Conversion MIMO Receiver Baseband.
E-Band Microwave Radio Digitizer
Samples wideband IF signals in 71-76 GHz and 81-86 GHz E-band point-to-point radios. The HMCAD1512's 1.5 GHz input bandwidth and 500 MSPS interleaved sample rate preserve modulation bandwidth for high-order QAM schemes, while the dual-channel architecture captures I and Q simultaneously without IQ phase imbalance. Routing the cross-point switch lets the same part service TX/RX or hot-standby chains, reducing BOM cost in small-cell backhaul hardware.
おすすめ
Digital Oscilloscope Front-End
Provides 8-bit vertical resolution at full 500 MSPS for entry-tier and channel-portable oscilloscopes. Bandwidth of 1.5 GHz meets mainstream serial-bus and embedded debug requirements, while the integrated cross-point switch simplifies AC/DC coupling and impedance-mode selection per channel. The 48-QFN 7x7 footprint enables 4-channel scope boards in a form factor similar to earlier 2-channel designs, expanding channel count without re-laying the analog front-end.
おすすめ
Radar Receiver Digitization
Captures short-range radar return pulses with dual-channel simultaneous sampling for I/Q downconversion chains. The HMCAD1512's programmable 500-1000 mVpp full-scale range lets designers match ADC dynamic range to antenna signal levels without external attenuators. Per ADI datasheet, the on-chip calibration of inter-channel gain and timing reduces the firmware burden of correcting interleaving artifacts in pulse-Doppler FFTs.
おすすめ
Communications Test Equipment
Vector signal analyzers and arbitrary waveform test platforms use the HMCAD1512 to digitize broadband modulated carriers. The 1.5 GHz input bandwidth supports carriers above 1 GHz while 500 MSPS oversampling provides headroom for digital downconversion and crest-factor measurement. The dual-channel design enables parallel capture of TX and RX paths for loopback EVM measurements in production test of cellular femtocells and small-cell base stations.
おすすめ
High-Speed Data Acquisition
Industrial and scientific DAQ platforms leverage the dual-channel synchronized sampling of the HMCAD1512 for sonar arrays, vibration monitoring, and particle-physics experiments. Tightly matched gain and timing between the two channels eliminates post-calibration routines in many applications. The 1.8V supplies and exposed pad layout simplify thermal integration into IP67 sealed enclosures where conduction cooling through the chassis ground plane is the only heat path.
おすすめ
Direct-Conversion MIMO Receiver Baseband
Dual-channel synchronized sampling at the baseband I/Q outputs of two parallel direct-conversion receivers. The HMCAD1512's programmable full-scale range lets designers match ADC input to the demodulator's differential output without op-amp buffers, reducing noise and cost in MIMO gateways and small-cell base stations. Per ADI datasheet the LVDS digital interface connects directly to most FPGAs without level translation.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: HMCAD1512 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | HMCAD1511 | HMCAD1520 | HMCAD1041LP4E | ADC081000CIYB |
|---|---|---|---|---|---|
| Package | 48-QFN (7x7) HVQCCN | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN family - same | 48-HLQFP - different |
| Brand | Analog Devices (Hittite) | Analog Devices | Analog Devices | Analog Devices | Texas Instruments |
| Resolution | 8 bit | 8 bit | 8 bit | 8 bit | 8 bit |
| Number of Channels | 2 (with cross-point switch) | 4 | 2 | 1 | 1 |
| Drop-in Pin-Compatible | (reference) | Yes | Yes | Same QFN family | No (different package) |
主な差別化要因
- Dual-channel 500 MSPS with integrated 2:2 cross-point switch （vs HMCAD1520)
- Pin-compatible upgrade path to 4-channel HMCAD1511 （vs HMCAD1511)
- True E-band tailored analog bandwidth （vs ADC081000CIYB)
設計ノート
Use separate analog and digital 1.8 V regulators for the HMCAD1512. Place 10 uF bulk plus 100 nF ceramic decoupling within 2 mm of each VA1V8 and VD1V8 pin to suppress the switching noise of the ADC's clock distribution from coupling into the analog front-end. Connect the exposed pad (pin 48) to a continuous ground plane on an inner layer to provide both thermal relief and a low-inductance return for the LVDS drivers.
Route all eight LVDS data pairs (D0 through D7) plus the data clock (DCLK) as 100-ohm differential microstrip or stripline on a controlled-impedance layer. Match pair lengths within +/- 5 mil and use length matching at the receiver to keep the DDR-like capture window inside the FPGA/ASIC set-up and hold time. Avoid routing LVDS traces over power planes or split ground planes, as returning currents will cause inter-lane skew and EMI.
Pin 39 and pin 45 on the HMCAD1512 are not interchangeable with the HMCAD1511 - per the EngineerZone HMCAD1511 replacement thread, both must be tied to ground on the HMCAD1512; failure to do so can cause the ADC to miscalibrate. Always re-validate the schematic on the HMCAD1511 reference design before transplanting an HMCAD1512 PCB layout, even though the parts share a footprint.
At full 500 MSPS interleaved sampling the HMCAD1512 dissipates up to approximately 1.0-1.5 W. The HVQCCN package (theta_JA about 30 C/W on a 4-layer JEDEC test board) limits the in-package die rise to about 45 C. In sealed modules or tightly stacked cards, install thermal vias under the exposed pad and connect them to the chassis ground to keep Tj below 105 C derating threshold.
コンプライアンス情報
RoHS-compliant per Analog Devices product page. AEC-Q100 not applicable - this is an RF/IF ADC for industrial/commercial use, not automotive. Manufacturer acquired original Hittite Microwave part line; product branding shows Hittite legacy datasheet revisions.
