ICL7653CSA - Zero-Drift Chopper Op Amp | Maxim Integrated
部品番号: ICL7653CSA ✓ 生産中ICL7653CSA 概要
An operational amplifier is a high-gain analog building block used to amplify differential voltage, buffer sensors, integrate signals, and drive feedback networks. The ICL7653 belongs to the chopper-stabilized operational-amplifier family, combining continuous-time signal handling with periodic correction of low-frequency offset and drift. This technique is especially useful in low-level instrumentation, bridge sensors, and precision current-feedback circuits.
The principal benefits are a 10 uV typical input offset voltage, 4 pA typical input bias current, and zero-drift operation. These characteristics reduce measurement errors caused by input mismatch and leakage, making the amplifier suitable for sensor interfaces where signals may be only millivolts in amplitude. The single-amplifier configuration also permits flexible gain, filtering, and feedback arrangements rather than fixing the application around a multi-channel device.
Chopper stabilization trades increased internal complexity for improved dc accuracy. The amplifier periodically corrects offset-related errors, while its internal correction network introduces periodic output artifacts around the chopping frequency. Layout, output filtering, and the selection of feedback components therefore influence whether those artifacts appear at the signal of interest. The ICL7653 is intended for low-level precision applications rather than high-speed waveform amplification.
Typical uses include bridge-transducer signal conditioning, low-current measurement, precision instrumentation, current-to-voltage conversion, and low-level sensor amplification. In these systems, the low bias current helps minimize loading of high-impedance sources, while the low offset voltage helps preserve accuracy near the input common-mode range. Each circuit must also provide suitable supply bypassing and account for output-noise components introduced by chopper correction.
For a new design, verify the required supply range, input common-mode range, output swing, stability, and noise spectrum against the Maxim Integrated ICL7653 manufacturer datasheet. Place input and output compensation or filtering components close to the amplifier pins, and observe the device's maximum total supply voltage. Because the ICL7653CSA is an 8-pin SOIC part, follow the numbered pin diagram and pin-description table when assigning PCB nets.
This page combines the ICL7653CSA's verified electrical characteristics, package information, sourcing details, application guidance, and replacement considerations. It also distinguishes documented drop-in candidates from related family members so engineers can evaluate PCB compatibility without assuming that similar amplifier specifications guarantee interchangeable operation.
ドロップイン代替品: ICL7653CSA — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ICL7653CSA (同一形状・フットプリント) — 相違点: Amplifier Type, Input Bias Current, Supply Voltage Range.
ICL7653BCSA
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ICL7653CSA 最大定格&電気的特性
| Amplifier Type | Single chopper-stabilized operational amplifier |
| Input Offset Voltage | 10 uV typical |
| Input Bias Current | 4 pA typical |
| Supply Voltage Range | Single ±8 V maximum |
| Zero-Drift Operation | Yes |
| Number of Channels | 1 channel |
| パッケージ | 8-pin SOIC |
| Package Width | 3.90 mm |
| 実装タイプ | Surface mount |
| Product Classification | Linear amplifier, zero-drift, single circuit |
ICL7653CSA 3.90 mm ピン配置ガイド
ICL7653CSA (3.90 mm パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: ICL7653CSA.
詳細は データシート をご参照ください。
主な用途
ICL7653CSA の用途: 6 件s: Bridge Transducer Signal Conditioning, High-Impedance Sensor Interface, Precision Current-to-Voltage Conversion, Low-Level Instrumentation Amplifier, Medical Signal Conditioning, Precision Test and Measurement.
Bridge Transducer Signal Conditioning
The ICL7653CSA fits low-level bridge-sensor front ends because its 10 uV typical input offset voltage and 4 pA typical input bias current reduce errors relative to small differential signals. It can amplify the bridge output in a differential configuration while preserving accuracy near the sensor output level. Place the device close to the bridge and reference network, provide local supply bypassing, and evaluate chopping-frequency components before filtering them at the amplifier output.
おすすめ
High-Impedance Sensor Interface
The ICL7653CSA is appropriate for high-impedance sensor interfaces because its 4 pA typical input bias current limits the voltage error introduced by finite source impedance. Combined with a 10 uV typical input offset voltage, it can preserve weak sensor outputs better than a general-purpose amplifier with higher bias current. The circuit should still verify input common-mode limits, leakage from PCB contamination, guarding, and output-noise behavior under the required source resistance.
おすすめ
Precision Current-to-Voltage Conversion
The ICL7653CSA can serve as the transimpedance element in a precision current-to-voltage converter when both signal current and source impedance are small. Its 4 pA typical bias current limits the error caused by current flowing into the input, and its 10 uV typical offset supports accurate measurement of low-level currents. Select feedback resistance carefully because noise gain, stability, bandwidth, and parasitic capacitance determine the achievable conversion ratio and response.
おすすめ
Low-Level Instrumentation Amplifier
The ICL7653CSA can be used in a discrete instrumentation-amplifier topology where low offset and low bias current are needed for a differential sensor signal. Two amplifier inputs can establish gain and common-mode rejection while a third amplifier provides a stable reference or output-buffer function in a multi-amplifier design. Matching resistor networks carefully and confirming each amplifier's common-mode range and output swing are essential because dc accuracy alone does not guarantee system-level rejection.
おすすめ
Medical Signal Conditioning
The ICL7653CSA is suitable for low-amplitude biomedical signal conditioning when dc offset from the electrodes or sensing element must be rejected. Its 10 uV typical input offset voltage and 4 pA typical input bias current support low-error amplification, while the 8-pin SOIC package allows a compact analog layout. Medical designs must still address patient protection, input protection, isolation, leakage, noise, application-specific qualification, and all applicable regulatory requirements.
おすすめ
Precision Test and Measurement
The ICL7653CSA can amplify small differential signals in bench instruments, programmable supplies, and measurement modules where offset drift would otherwise impair accuracy. The 10 uV typical input offset and 4 pA typical bias current are useful near the measurement floor, while external calibration can compensate fixed system error. Designers should characterize chopping-related spectral components, configure compensation correctly, and ensure the chosen loop gain provides adequate bandwidth and phase margin.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ICL7653CSA — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ICL7653BCSA |
|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated |
| Package | 8-pin SOIC | 8-pin SOIC |
| Amplifier Configuration | Single amplifier | Single amplifier |
| Stabilization Method | Chopper stabilized, zero drift | Chopper stabilized |
| Maximum Supply Range | ±8 V | ±8 V |
主な差別化要因
- Low offset voltage for precision dc measurement (vs ICL7653BCSA)
- Very low input bias current (vs ICL7653BCSA)
- Single-amplifier 8-pin SOIC implementation (vs ICL7653BCSA)
設計ノート
Route the ICL7653CSA input, output, and compensation connections with short traces and keep high-impedance nodes away from switching nodes and noisy digital paths. Place compensation components directly at their associated pins to minimize parasitic feedback. Because chopper correction can introduce narrow-band artifacts, reserve an output-filter location and determine its corner frequency from the signal bandwidth and measured noise spectrum.
Follow the manufacturer datasheet guidance for supply decoupling and place the required bypass capacitor close to the device's supply and ground pins. Check the actual supply combination against the ±8 V maximum range, including tolerance, transients, and startup overshoot. The amplifier's low offset voltage does not protect it from supply disturbance, so power-supply noise and ground-return design remain important parts of the measurement error budget.
Do not treat ICL7653BCSA as an automatic substitute for ICL7653CSA solely because both names contain ICL7653. Verify the complete pin-description table, package drawing, temperature grade, supply limits, input common-mode range, compensation requirements, and electrical characteristics. Preserve the documented strobe behavior and avoid enabling an unintended operating condition; the family relationship alone is insufficient proof of production interchangeability.
Characterize the amplifier output over the frequency range of interest because chopper correction introduces periodic components that may not be apparent in ordinary dc measurements. Use an oscilloscope or spectrum analyzer to observe the correction-related region, then choose filtering that suppresses those components without disrupting the required signal bandwidth. Avoid overstating closed-loop bandwidth when a narrow notch filter or an external compensation network is added.
コンプライアンス情報
Compliance status was not stated in the manufacturer or distributor information and must be confirmed using the manufacturer datasheet or product documentation.