ISL83485IB - 3.3V 10Mbps RS-485/RS-422 | Renesas
部品番号: ISL83485IB ✓ 生産中ISL83485IB 概要
A transceiver converts digital logic-level signals into differential signals suitable for reliable data transmission over longer cable runs. In the broader semiconductor hierarchy, the ISL83485IB belongs to the interface IC class and specifically implements the RS-485/RS-422 physical-layer standard. Balanced differential signaling improves noise immunity and permits communication between equipment located at different ground potentials when implemented with suitable protection and grounding practices.
Renesas describes the ISL83485 family as a BiCMOS, 3.3 V-powered product family specified for 3.0 V to 3.6 V supplies, allowing a 10% supply-voltage tolerance. Its advertised 10 Mbps maximum data rate makes it suitable for industrial control, instrumentation, factory automation, data acquisition and other balanced-bus systems requiring more bandwidth than conventional low-speed RS-485 links.
The half-duplex architecture allows the same differential bus conductors to carry transmitted and received data at different times. This reduces the number of external bus connections compared with a full-duplex implementation, but the system must ensure that only one device transmits at a time. The driver's switching behavior, receiver thresholds, supply tolerances and external network termination remain central to dependable operation.
Typical uses include PLC and sensor networks, industrial communication links, building-control equipment, test and measurement instruments, and embedded data-acquisition systems. The 8-pin SOIC package is also suitable for compact, surface-mounted equipment. Its package should be treated as SOIC-8 when planning a PCB footprint, while exact exposed-pad and thermal details should be checked in the manufacturer datasheet.
Designers should pay close attention to bus termination, common-mode voltage, grounding, protection, and the timing of driver-enable control. Differential routing should use a balanced pair, avoid splits in the trunk, and be terminated only where required by the system topology. Decoupling capacitors should be placed close to the supply and ground pins, while external protection may be needed for exposed industrial cabling.
This page combines the manufacturer's interface and supply information with practical package, replacement, comparison, and design guidance. It is intended to help engineers identify whether the ISL83485IB fits a 3.3 V, half-duplex RS-485/RS-422 design before completing footprint, signal-integrity, and protection reviews.
ドロップイン代替品: ISL83485IB — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ISL83485IB (同一形状・フットプリント) — 相違点: Package.
ISL83485IBZ-T
✅ ドロップイン価格はお問い合わせください
データシートを見る →ISL83483IBZ-T
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ISL83485IB-T
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ST3485EBDR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ISL83485IB 仕様
| Product Type | RS-485/RS-422 transceiver |
| 電源電圧 | 3.3 V |
| Operating Supply Range | 3.0 V to 3.6 V |
| Supply Tolerance | 10% |
| Maximum Data Rate | 10 Mbps |
| Duplex Mode | Half duplex |
| Supported Standards | RS-485 and RS-422 |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Process Technology | BiCMOS |
| パッケージ | 8-pin SOIC |
| Lead Count | 8 leads |
| 実装タイプ | Surface mount |
ISL83485IB 8-pin soic ピン配置ガイド
ISL83485IB (8-pin soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: ISL83485IB.
詳細は データシート をご参照ください。
主な用途
ISL83485IB の用途: 6 件s: Industrial PLC and Sensor Networks, Factory Data Acquisition, Building Control Networks, Test and Measurement Instruments, Embedded Equipment Gateways, Robotics and Motor-Control Systems.
Industrial PLC and Sensor Networks
The ISL83485IB fits 3.3 V industrial control and sensor networks because it combines one driver, one receiver, half-duplex operation, and a 10 Mbps maximum data rate in an 8-pin SOIC package. It can place a higher-bandwidth balanced interface between a controller and remote sensors, actuators, or automation modules. The BiCMOS family is specified from 3.0 V to 3.6 V, accommodating a nominal 3.3 V rail with 10% supply tolerance. In an implementation, the transceiver connects the controller UART to a differential bus while the firmware controls driver enable so only one node transmits at a time. The main engineering considerations are bus contention prevention, proper termination at trunk endpoints, common-mode compatibility, and protection for exposed factory cabling.
おすすめ
Factory Data Acquisition
The ISL83485IB is suitable for factory data-acquisition equipment requiring a compact, high-speed balanced interface. Its 10 Mbps rated rate can accommodate concentrated measurement streams where a slower RS-485 link would become the bottleneck, while the half-duplex topology minimizes bus wiring compared with a full-duplex design. The 8-pin SOIC package simplifies placement beside a controller or sensor interface, and the 3.0 V to 3.6 V supply range supports 3.3 V embedded systems. Place the device near the protected connector and route the bus as a controlled-impedance differential pair. Decoupling must be located close to the supply pins, while surge and ESD protection may be added on the line side when the acquisition system connects to long factory cables.
おすすめ
Building Control Networks
The ISL83485IB can serve as the physical-layer interface in a 3.3 V building-control network that distributes commands and status data over a balanced bus. Its half-duplex RS-485/RS-422 capability allows controllers, room modules, and field interfaces to share wiring while supporting communication rates up to 10 Mbps for local high-speed links. The 8-pin SOIC package is appropriate for compact controller boards, and the family's 3.0 V to 3.6 V range accommodates a 3.3 V regulated supply. In a building installation, the transceiver should be paired with protected cabling and a defined grounding strategy because building wiring can experience large potential differences. Firmware must enforce exclusive bus access, and the PCB should keep the differential route short, symmetric, and away from high-energy switching nodes.
おすすめ
Test and Measurement Instruments
The ISL83485IB is appropriate for test and measurement instruments that need to exchange commands or sampled results over a balanced laboratory bus. Its 10 Mbps maximum data rate reduces transfer time for compact automated test systems, while the half-duplex architecture supports economical wiring between an instrument controller and remote fixtures. The device operates from a nominal 3.3 V supply and fits an 8-pin SOIC footprint, making it practical for portable and benchtop equipment. Connect the transceiver to the instrument's digital controller and place it near the cable-entry interface so protection devices can be placed directly at the connector. Use a balanced cable, terminate the bus according to the actual topology, and test the system with the longest intended cable run to verify receiver behavior under real noise and loading conditions.
おすすめ
Embedded Equipment Gateways
The ISL83485IB fits embedded gateways that translate between a local processor and older RS-485 or RS-422 equipment. Its 3.3 V operation aligns with modern embedded logic, its 8-pin SOIC package is easy to route on compact boards, and its 10 Mbps capability supports high-throughput command and telemetry links. The half-duplex interface permits one shared differential pair for both directions, reducing connector pin requirements compared with a full-duplex solution. Place the transceiver between the host serial controller and the external bus connector, using short traces from the transceiver to the protection network. The firmware should include bus turnaround timing and collision handling. Verify that the external equipment tolerates the transceiver's 3.3 V signaling and supply range before deploying the gateway in the field.
おすすめ
Robotics and Motor-Control Systems
The ISL83485IB can support reliable command and feedback links in robotics and motor-control systems where a 3.3 V controller communicates with remote axis modules over a balanced bus. The 10 Mbps rate accommodates compact control traffic, while the half-duplex configuration allows bidirectional communication on the same pair and helps limit connector count. BiCMOS technology and the 3.0 V to 3.6 V supply range suit modern embedded motor controllers. Locate the transceiver near the external connector and place surge protection at the cable boundary, since motor systems can introduce large transients and ground offsets. Differential traces should run as a matched pair without test pads that create unnecessary stubs. Firmware must guarantee that command transmitters do not overlap, particularly during emergency stop or fault-recovery sequences.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ISL83485IB — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ISL83485IBZ-T | ISL83483IBZ-T | ISL83485IB-T | ST3485EBDR |
|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | SOIC-8 |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | STMicroelectronics |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Maximum Data Rate | 10 Mbps | 10 Mbps | 10 Mbps | 10 Mbps | At least 12 Mbps |
| Duplex Mode | Half duplex | Half duplex | Half duplex | Half duplex | Half duplex |
| Supported Interfaces | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
| Driver and Receiver Count | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver |
主な差別化要因
- 10 Mbps class operation supports higher-bandwidth balanced links (vs ISL83483IBZ-T)
- The ST3485EBDR provides a higher guaranteed data-rate ceiling (vs ST3485EBDR)
- BiCMOS operation and a 10% supply tolerance are explicit family specifications (vs ST3485EBDR)
- Same-family alternatives simplify electrical and timing review (vs ISL83485IBZ-T)
設計ノート
Route the differential bus as a closely matched pair from the transceiver to the protection and connector area. Avoid stubs, test pads, impedance discontinuities, and routing over split plane boundaries. Keep the pair away from motor drives, switching power stages, and high-current return paths. If the PCB reaches the cable connector, place transient-protection devices close to the connector so surge current is diverted before reaching the transceiver pins.
Half-duplex operation requires exclusive access to the shared bus. Enable the driver only while the node owns transmission and leave adequate turnaround time before the receiver is used. Another common error is treating a 10 Mbps headline rate as a guaranteed long-cable performance figure: data rate, cable length, topology, termination, and noise immunity must be evaluated together. Use the family datasheet and application guidance when selecting network values.
Place the required supply-decoupling capacitor immediately beside the transceiver's supply and ground pins, and keep the return path short. The ISL83485 family is specified for a 3.0 V to 3.6 V range, so verify startup behavior, supply droop, and noise at the actual 3.3 V rail rather than assuming an ideal source. Avoid sharing a narrow return path between the transceiver and switching or high-current loads on the board.
If electromagnetic-interference margin is more important than maximum edge rate, evaluate ISL83483IBZ-T, whose slew-rate-limited driver is specifically described as reducing EMI and minimizing reflections from improperly terminated lines. The ISL83485IB remains appropriate when maximum throughput is the priority. Confirm edge rate, bus voltage, termination, and timing against the system requirements before changing device families.
コンプライアンス情報
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for the exact ISL83485IB ordering code were stated in the product information. Request the applicable manufacturer declarations before qualifying a regulated production design.