Renesas Electronics

ISL83485IB - 3.3V 10Mbps RS-485/RS-422 | Renesas

MPN: ISL83485IB ✓ فعال
3.3 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
حداقل سفارش: 1 |

ISL83485IB نمای کلی

The Renesas Electronics ISL83485IB is a 3.3 V, half-duplex RS-485/RS-422 transceiver supporting data rates up to 10 Mbps in an 8-pin SOIC package. The device combines one driver and one receiver, multiplexing the bus driver and receiver connections to support economical half-duplex communication over a balanced twisted-pair interface.

A transceiver converts digital logic-level signals into differential signals suitable for reliable data transmission over longer cable runs. In the broader semiconductor hierarchy, the ISL83485IB belongs to the interface IC class and specifically implements the RS-485/RS-422 physical-layer standard. Balanced differential signaling improves noise immunity and permits communication between equipment located at different ground potentials when implemented with suitable protection and grounding practices.

Renesas describes the ISL83485 family as a BiCMOS, 3.3 V-powered product family specified for 3.0 V to 3.6 V supplies, allowing a 10% supply-voltage tolerance. Its advertised 10 Mbps maximum data rate makes it suitable for industrial control, instrumentation, factory automation, data acquisition and other balanced-bus systems requiring more bandwidth than conventional low-speed RS-485 links.

The half-duplex architecture allows the same differential bus conductors to carry transmitted and received data at different times. This reduces the number of external bus connections compared with a full-duplex implementation, but the system must ensure that only one device transmits at a time. The driver's switching behavior, receiver thresholds, supply tolerances and external network termination remain central to dependable operation.

Typical uses include PLC and sensor networks, industrial communication links, building-control equipment, test and measurement instruments, and embedded data-acquisition systems. The 8-pin SOIC package is also suitable for compact, surface-mounted equipment. Its package should be treated as SOIC-8 when planning a PCB footprint, while exact exposed-pad and thermal details should be checked in the manufacturer datasheet.

Designers should pay close attention to bus termination, common-mode voltage, grounding, protection, and the timing of driver-enable control. Differential routing should use a balanced pair, avoid splits in the trunk, and be terminated only where required by the system topology. Decoupling capacitors should be placed close to the supply and ground pins, while external protection may be needed for exposed industrial cabling.

This page combines the manufacturer's interface and supply information with practical package, replacement, comparison, and design guidance. It is intended to help engineers identify whether the ISL83485IB fits a 3.3 V, half-duplex RS-485/RS-422 design before completing footprint, signal-integrity, and protection reviews.

جایگزین‌های drop-in برای ISL83485IB — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای ISL83485IB (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package.

Renesas Electronics
Package: 8-SOIC (IB) 3.9 mm
مقایسه با ISL83485IB →

ISL83485IBZ-T

✅ جایگزین مستقیم
Renesas Electronics
📦 8-SOIC
Transceiver · 1/1 · Half · RS-422, RS-485 · 10 Mbps · 3.3 V · 3.0 V to 3.6 V · 1/8 unit-load (up to 256 nodes)

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

ISL83483IBZ-T

✅ جایگزین مستقیم
📦 8-SOIC
Same 3.3 V, 10 Mbps, half-duplex family class and 8-SOIC footprint, but uses a slew-rate-limited driver to reduce EMI; rated speed differs by 0 Mbps.

📋 جایگزین مرجع (خارج از کاتالوگ)

ISL83485IB-T

✅ جایگزین مستقیم
📦 8-SOIC
Same 3.3 V, 10 Mbps, half-duplex transceiver configuration and 8-SOIC package; the ordering suffix changes ordering or shipping attributes, with a 0 Mbps rated-speed difference.

📋 جایگزین مرجع (خارج از کاتالوگ)

ST3485EBDR

✅ جایگزین مستقیم
📦 SOIC-8
Same 3.3 V half-duplex RS-485/RS-422 interface class, but the guaranteed data rate is at least 12 Mbps versus 10 Mbps, a 20% increase.

📋 جایگزین مرجع (خارج از کاتالوگ)

ISL83485IB مشخصات

Product Type RS-485/RS-422 transceiver
ولتاژ تغذیه 3.3 V
Operating Supply Range 3.0 V to 3.6 V
Supply Tolerance 10%
Maximum Data Rate 10 Mbps
Duplex Mode Half duplex
Supported Standards RS-485 and RS-422
Driver Count 1 driver
Receiver Count 1 receiver
Process Technology BiCMOS
بسته‌بندی 8-pin SOIC
Lead Count 8 leads
نوع نصب Surface mount

راهنمای پیکربندی پین ISL83485IB 8-pin soic

پیکربندی پین برای ISL83485IB (پکیج 8-pin soic). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 8-pin soic برای ISL83485IB

داده پین‌آوت تفصیلی موجود نیست برای ISL83485IB.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

ISL83485IB مناسب است برای 6 کاربردs: Industrial PLC and Sensor Networks, Factory Data Acquisition, Building Control Networks, Test and Measurement Instruments, Embedded Equipment Gateways, Robotics and Motor-Control Systems.

🏭

Industrial PLC and Sensor Networks

The ISL83485IB fits 3.3 V industrial control and sensor networks because it combines one driver, one receiver, half-duplex operation, and a 10 Mbps maximum data rate in an 8-pin SOIC package. It can place a higher-bandwidth balanced interface between a controller and remote sensors, actuators, or automation modules. The BiCMOS family is specified from 3.0 V to 3.6 V, accommodating a nominal 3.3 V rail with 10% supply tolerance. In an implementation, the transceiver connects the controller UART to a differential bus while the firmware controls driver enable so only one node transmits at a time. The main engineering considerations are bus contention prevention, proper termination at trunk endpoints, common-mode compatibility, and protection for exposed factory cabling.

📊

Factory Data Acquisition

The ISL83485IB is suitable for factory data-acquisition equipment requiring a compact, high-speed balanced interface. Its 10 Mbps rated rate can accommodate concentrated measurement streams where a slower RS-485 link would become the bottleneck, while the half-duplex topology minimizes bus wiring compared with a full-duplex design. The 8-pin SOIC package simplifies placement beside a controller or sensor interface, and the 3.0 V to 3.6 V supply range supports 3.3 V embedded systems. Place the device near the protected connector and route the bus as a controlled-impedance differential pair. Decoupling must be located close to the supply pins, while surge and ESD protection may be added on the line side when the acquisition system connects to long factory cables.

🏠

Building Control Networks

The ISL83485IB can serve as the physical-layer interface in a 3.3 V building-control network that distributes commands and status data over a balanced bus. Its half-duplex RS-485/RS-422 capability allows controllers, room modules, and field interfaces to share wiring while supporting communication rates up to 10 Mbps for local high-speed links. The 8-pin SOIC package is appropriate for compact controller boards, and the family's 3.0 V to 3.6 V range accommodates a 3.3 V regulated supply. In a building installation, the transceiver should be paired with protected cabling and a defined grounding strategy because building wiring can experience large potential differences. Firmware must enforce exclusive bus access, and the PCB should keep the differential route short, symmetric, and away from high-energy switching nodes.

🔧

Test and Measurement Instruments

The ISL83485IB is appropriate for test and measurement instruments that need to exchange commands or sampled results over a balanced laboratory bus. Its 10 Mbps maximum data rate reduces transfer time for compact automated test systems, while the half-duplex architecture supports economical wiring between an instrument controller and remote fixtures. The device operates from a nominal 3.3 V supply and fits an 8-pin SOIC footprint, making it practical for portable and benchtop equipment. Connect the transceiver to the instrument's digital controller and place it near the cable-entry interface so protection devices can be placed directly at the connector. Use a balanced cable, terminate the bus according to the actual topology, and test the system with the longest intended cable run to verify receiver behavior under real noise and loading conditions.

🌐

Embedded Equipment Gateways

The ISL83485IB fits embedded gateways that translate between a local processor and older RS-485 or RS-422 equipment. Its 3.3 V operation aligns with modern embedded logic, its 8-pin SOIC package is easy to route on compact boards, and its 10 Mbps capability supports high-throughput command and telemetry links. The half-duplex interface permits one shared differential pair for both directions, reducing connector pin requirements compared with a full-duplex solution. Place the transceiver between the host serial controller and the external bus connector, using short traces from the transceiver to the protection network. The firmware should include bus turnaround timing and collision handling. Verify that the external equipment tolerates the transceiver's 3.3 V signaling and supply range before deploying the gateway in the field.

🤖

Robotics and Motor-Control Systems

The ISL83485IB can support reliable command and feedback links in robotics and motor-control systems where a 3.3 V controller communicates with remote axis modules over a balanced bus. The 10 Mbps rate accommodates compact control traffic, while the half-duplex configuration allows bidirectional communication on the same pair and helps limit connector count. BiCMOS technology and the 3.0 V to 3.6 V supply range suit modern embedded motor controllers. Locate the transceiver near the external connector and place surge protection at the cable boundary, since motor systems can introduce large transients and ground offsets. Differential traces should run as a matched pair without test pads that create unnecessary stubs. Firmware must guarantee that command transmitters do not overlap, particularly during emergency stop or fault-recovery sequences.

What is the ISL83485IB?
The ISL83485IB is a 3.3 V, half-duplex RS-485/RS-422 transceiver from Renesas Electronics. It combines one driver and one receiver, supports balanced communication at rates up to 10 Mbps, and is offered in an 8-pin SOIC package. According to the Renesas ISL83485 product page, the device uses BiCMOS technology and is intended for 3.0 V to 3.6 V supply rails.
What is the operating voltage of ISL83485IB?
The ISL83485IB operates from a nominal 3.3 V supply over a 3.0 V to 3.6 V range. Renesas specifies the ISL83485 family for a 10% supply-voltage tolerance, making it suitable for systems whose 3.3 V rail can vary across that permitted interval. The exact operating-temperature limits and detailed electrical test conditions are recorded in the manufacturer datasheet.
What is the maximum data rate of ISL83485IB?
The ISL83485IB supports a maximum data rate of 10 Mbps. This makes it suitable for balanced, half-duplex industrial links that carry control commands, sampled data, or configuration traffic faster than traditional low-speed RS-485 networks. Actual application throughput also depends on cable length, topology, termination, signal loss, and the latency introduced by the selected bus protocol.
Where can I download the ISL83485IB datasheet PDF?
The ISL83485IB datasheet is available from Renesas through the manufacturer document page for the ISL83483, ISL83485, ISL83488, ISL83490, and ISL83491 family. The document provides the authoritative pin descriptions, electrical characteristics, timing information, power behavior, and application guidance. Use the manufacturer PDF for PCB implementation and production design rather than relying on a secondary component summary.
Where can I find the ISL83485IB pinout?
The ISL83485IB pinout is defined in the Renesas family datasheet and its package drawing for the 8-pin SOIC device. The package is designated 8-SOIC by the manufacturer. When assigning PCB tracks, use the pin-description table and standard pin-1 orientation in the datasheet so the differential inputs, driver outputs, logic controls, supply, and ground are connected correctly.
ISL83485IB vs ISL83485IBZ-T - which is the better choice?
The ISL83485IB and ISL83485IBZ-T belong to the same ISL83485 transceiver family and are associated with the same 8-SOIC electrical configuration, including 3.3 V operation and a 10 Mbps data rate. Their ordering suffixes can encode packaging and ordering information, so the installed form rather than the basic transceiver function may determine the correct selection. Confirm reel-versus-tube requirements and temperature-grade details before substitution.
When should I choose ISL83485IB over ISL83483IBZ-T?
Choose the ISL83485IB when the design specifically calls for the ISL83485 high-speed transceiver configuration and requires the 10 Mbps class of operation in an 8-pin SOIC package. Choose ISL83483IBZ-T when slew-rate-limited driver behavior is preferable for electromagnetic-interference control or reflection reduction. Confirm the exact pin functions and timing requirements in the shared family datasheet before deciding.
Can the ST3485EBDR replace the ISL83485IB?
The ST3485EBDR is a candidate drop-in replacement because it is described as a 3.3 V, low-power, half-duplex RS-485/RS-422 transceiver with an 8-pin SOIC-compatible format. Its guaranteed data rate is at least 12 Mbps, compared with the ISL83485IB's 10 Mbps rating. Verify pin mapping, logic-control polarity, receiver thresholds, supply tolerances, and protection requirements in both datasheets before production use.
What is the best drop-in replacement for ISL83485IB?
The ST3485EBDR is the best-supported cross-brand candidate in the available replacement data because it is a 3.3 V, half-duplex RS-485/RS-422 transceiver rated for at least 12 Mbps and offered in an 8-pin SOIC-compatible package. No universal replacement can be approved from package and headline specifications alone. Validate pin functions, enable timing, bus impedance, common-mode limits, and system-level fault behavior before releasing the substitution.
Is ISL83485IB suitable for industrial RS-485 networks?
The ISL83485IB is well suited to industrial RS-485 networks that operate from a 3.3 V supply and require balanced half-duplex communication up to 10 Mbps. Its BiCMOS implementation and 3.0 V to 3.6 V supply range support compact embedded systems, PLC interfaces, industrial sensors, and factory data-acquisition equipment. The bus still requires suitable termination, grounding, surge protection, and a protocol that controls transmit-enable timing.
What should designers check before using ISL83485IB in a half-duplex bus?
Designers should confirm that only one transceiver drives the bus at a time and that driver-enable timing leaves adequate guard time around frame boundaries. The Renesas family datasheet identifies the ISL83483 and ISL83485 as half-duplex devices that multiplex receive inputs and transmit outputs. PCB layout should preserve a symmetric differential pair, minimize stubs, and place power-decoupling and protection components close to their associated pins.
How do I terminate and route an ISL83485IB RS-485 bus?
Route the ISL83485IB differential bus as a balanced pair on the PCB and minimize impedance discontinuities, branch stubs, and loop area. Add termination resistors only where the chosen bus topology requires them, normally at the physical ends of the trunk. The manufacturer's application guidance should be consulted for driver waveform, cable length, and grounding details because inappropriate termination or common-mode conditions can impair reliable reception.
Where can I buy ISL83485IB and check its current availability?
Use the Request a Quote form on this page to ask about ISL83485IB availability, current lead time, order quantity, and the required 8-SOIC shipping configuration. The manufacturer lists the ISL83485 family as active, but production planning should still confirm current lot availability and any scheduled changes for the exact ordering code. No static availability or price claim should be made without a current quotation.
What is the lead time for ISL83485IB?
The current lead time for ISL83485IB should be confirmed through the Request a Quote form on this page using the exact MPN and required package or shipping form. Lead time can vary with manufacturer inventory, incoming supply, production schedules, order quantity, and component traceability requirements. For new production, provide the intended quantity and downstream assembly schedule so the supplier can confirm the appropriate allocation.
What are the key specifications engineers should know about ISL83485IB?
The principal ISL83485IB specifications are a nominal 3.3 V supply, a 3.0 V to 3.6 V operating range, half-duplex operation, one driver, one receiver, RS-485/RS-422 support, and a maximum data rate of 10 Mbps. The device uses BiCMOS technology and is packaged in an 8-pin SOIC. Renesas additionally specifies the family for 10% supply tolerance, a useful constraint when validating a 3.3 V system rail.

داده‌های مرجع مهندسی برای ISL83485IB — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the ISL83485IB when a compact 8-pin SOIC design requires a 3.3 V, half-duplex RS-485/RS-422 transceiver with operation up to 10 Mbps and a high-speed driver. Select ISL83483IBZ-T instead when slew-rate-limited edges are preferred to reduce EMI or control reflections; confirm its timing in the shared family documentation. Use an ISL83485IB ordering variant when the required tape-and-reel, temperature, or purchasing configuration differs from the target code. Consider the ST3485EBDR as a cross-brand candidate when its higher guaranteed data rate and complete electrical characteristics satisfy the design, but verify pin mapping, enable polarity, thresholds, protection, and supply limits. None of these choices should be treated as automatically interchangeable until the complete manufacturer datasheet requirements and application-level bus tests are satisfied.

مقایسه با جایگزین‌ها

پارامتر این محصول ISL83485IBZ-T ISL83483IBZ-T ISL83485IB-T ST3485EBDR
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC SOIC-8
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics STMicroelectronics
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V
Maximum Data Rate 10 Mbps 10 Mbps 10 Mbps 10 Mbps At least 12 Mbps
Duplex Mode Half duplex Half duplex Half duplex Half duplex Half duplex
Supported Interfaces RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422
Driver and Receiver Count 1 driver and 1 receiver 1 driver and 1 receiver 1 driver and 1 receiver 1 driver and 1 receiver 1 driver and 1 receiver

تفاوت‌های کلیدی

  • 10 Mbps class operation supports higher-bandwidth balanced links (در مقابلISL83483IBZ-T)
  • The ST3485EBDR provides a higher guaranteed data-rate ceiling (در مقابلST3485EBDR)
  • BiCMOS operation and a 10% supply tolerance are explicit family specifications (در مقابلST3485EBDR)
  • Same-family alternatives simplify electrical and timing review (در مقابلISL83485IBZ-T)

یادداشت‌های طراحی

Route the differential bus as a closely matched pair from the transceiver to the protection and connector area. Avoid stubs, test pads, impedance discontinuities, and routing over split plane boundaries. Keep the pair away from motor drives, switching power stages, and high-current return paths. If the PCB reaches the cable connector, place transient-protection devices close to the connector so surge current is diverted before reaching the transceiver pins.

Half-duplex operation requires exclusive access to the shared bus. Enable the driver only while the node owns transmission and leave adequate turnaround time before the receiver is used. Another common error is treating a 10 Mbps headline rate as a guaranteed long-cable performance figure: data rate, cable length, topology, termination, and noise immunity must be evaluated together. Use the family datasheet and application guidance when selecting network values.

Place the required supply-decoupling capacitor immediately beside the transceiver's supply and ground pins, and keep the return path short. The ISL83485 family is specified for a 3.0 V to 3.6 V range, so verify startup behavior, supply droop, and noise at the actual 3.3 V rail rather than assuming an ideal source. Avoid sharing a narrow return path between the transceiver and switching or high-current loads on the board.

If electromagnetic-interference margin is more important than maximum edge rate, evaluate ISL83483IBZ-T, whose slew-rate-limited driver is specifically described as reducing EMI and minimizing reflections from improperly terminated lines. The ISL83485IB remains appropriate when maximum throughput is the priority. Confirm edge rate, bus voltage, termination, and timing against the system requirements before changing device families.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for the exact ISL83485IB ordering code were stated in the product information. Request the applicable manufacturer declarations before qualifying a regulated production design.

تاریخ تأیید داده‌ها: 2026-11-15 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

ISL83485IB ISL83485IB datasheet ISL83485IB pinout ISL83485IB datasheet pdf ISL83485IB equivalent ISL83485IB replacement ISL83485IB footprint ISL83485IB price ISL83485IB stock Renesas ISL83485IB ISL83485IB vs ST3485EBDR ISL83485IB RS-485 transceiver ISL83485IB application circuit

قطعات و اصطلاحات مرتبط

Renesas Electronics ISL83485IB ISL83485IBZ-T ISL83483IBZ-T ST3485EBDR RS-485 RS-422 transceiver interface IC half-duplex communication differential signaling balanced bus BiCMOS 3.3 V power supply 10 Mbps data rate 8-pin SOIC SOIC package family surface-mount package industrial automation factory data acquisition building control EMC driver enable common-mode voltage
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ