ISL83699IR - Low-Voltage Quad SPDT Analog Switch | Renesas
部品番号: ISL83699IR ✓ 生産中ISL83699IR 概要
An analog switch is a semiconductor device that connects or disconnects analog signal paths under digital control. A quad SPDT configuration provides four independent selectors, each able to choose between two signal paths. This makes the ISL83699IR useful in applications such as battery-powered instrumentation, mobile equipment, communication interfaces, and test systems where low-voltage logic compatibility, fast switching, and low on-resistance are important.
Key features include an on-resistance of 0.26 ohm, switching times of tON = 10 ns and tOFF = 7 ns, and compatibility with 1.8 V digital logic when operated from a single 3 V supply. The low-voltage operating range allows the switch to operate directly from energy-efficient system rails. The 3 x 3 mm 16-QFN package reduces board area while supporting dense analog and mixed-signal layouts.
The switch is bidirectional, so signal paths can be routed in either direction. Bidirectional operation is valuable when a shared line must connect a peripheral, test point, or alternate signal source without requiring a directional multiplexer. The 2:1 architecture supports source selection, signal swapping, isolation, and bus-sharing functions in compact systems.
Typical applications include mobile-phone accessory routing, portable measurement equipment, battery-powered sensor interfaces, communication modules, and general-purpose analog signal routing. Designers should confirm that signal amplitudes remain within the device’s operating limits and that control logic levels meet the datasheet requirements. Adequate input and output decoupling, short analog traces, and careful grounding help preserve switching performance.
The principal design trade-off is the very low supply-voltage range. The ISL83699IR is optimized for 1.65 V to 3.6 V systems rather than higher-voltage rails. Designers using the same package in another design should verify control thresholds, signal swing, switching timing, and the exposed-pad connection before committing to a footprint.
This product page combines the manufacturer’s operating limits and switching characteristics with package information, application guidance, comparison data, and practical design notes. It is intended to accelerate engineering selection while keeping the final circuit decisions tied to the manufacturer datasheet and board-level requirements.
ドロップイン代替品: ISL83699IR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
ISL83699IR-T
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ISL83699IR 最大定格&電気的特性
| Device Type | Quad SPDT bidirectional analog switch |
| Number of Circuits | 4 circuits |
| Switch Configuration | 2:1 SPST per circuit |
| Supply Voltage Range | 1.65 V to 3.6 V |
| On-Resistance | 0.26 ohm |
| Catalog On-Resistance | 450 mOhm |
| Turn-On Time | 10 ns |
| Turn-Off Time | 7 ns |
| Logic Compatibility | 1.8 V compatible with a single 3 V supply |
| Signal Direction | Bidirectional |
| パッケージ | 16-QFN, 3 x 3 mm |
| 実装タイプ | Surface mount |
| ピン数 | 16 pins |
| Supplier Eligibility | Support is limited to customers who have already adopted these products |
ISL83699IR 16-qfn, 3 x 3 mm ピン配置ガイド
ISL83699IR (16-qfn, 3 x 3 mm パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: ISL83699IR.
詳細は データシート をご参照ください。
主な用途
ISL83699IR の用途: 6 件s: Battery-Powered Portable Equipment, Mobile Radio Signal Routing, Portable Measurement and Test Systems, Battery Sensor Interface Routing, Communications Line Multiplexing, Low-Voltage Audio and Control Routing.
Battery-Powered Portable Equipment
The ISL83699IR fits battery-powered equipment that must route several low-voltage signals within a compact board. Its 1.65 V to 3.6 V single-supply range allows direct operation from common portable-system rails, while the 0.26 ohm on-resistance limits signal-path loss. Four independent 2:1 selectors provide flexible routing without requiring four separate packages. The 16-QFN 3 x 3 mm package also preserves PCB area for display, radio, and sensing subsystems.
おすすめ
Mobile Radio Signal Routing
The ISL83699IR is suitable for switching low-frequency or baseband paths in mobile communication hardware. Bidirectional conduction lets a shared node connect to more than one peripheral without constraining signal direction, while tON = 10 ns and tOFF = 7 ns provide fast source selection. The 1.8 V-compatible control inputs support integration with 3 V logic, and the small 3 x 3 mm footprint reduces routing congestion in densely populated radio modules.
おすすめ
Portable Measurement and Test Systems
Portable test equipment can use the ISL83699IR to connect a common analog node to one of two signal sources. The fast 10 ns turn-on and 7 ns turn-off transitions support controlled measurement setup, while the low 0.26 ohm on-resistance helps preserve signal integrity at low supply voltages. Its four-channel quad SPDT organization allows multiple selections to be routed through one compact 16-QFN footprint, reducing component count on crowded instrument boards.
おすすめ
Battery Sensor Interface Routing
The ISL83699IR can route sensor outputs or excitation paths in compact battery-operated sensing equipment. Bidirectional switching supports designs where a line must move signals between a sensor, test circuit, and host controller. Operation from 1.65 V to 3.6 V aligns with energy-efficient sensor nodes, and the 450 mOhm catalog on-resistance provides a low-impedance path. Firmware should avoid asserting conflicting routes simultaneously and should honor power-up control states.
おすすめ
Communications Line Multiplexing
The quad 2:1 structure of the ISL83699IR supports line multiplexing where two signal sources must share a communications path. Its low on-resistance minimizes loss in the selected route, and 10 ns/7 ns switching speeds support high-rate control of alternate paths. The bidirectional architecture is useful for shared buses and configurable peripheral links. Designers should verify bandwidth, off-state isolation, and allowable signal swing in the manufacturer datasheet for the specific line standard.
おすすめ
Low-Voltage Audio and Control Routing
The ISL83699IR can select between low-voltage audio, control, or auxiliary paths in compact multi-function equipment. Its 0.26 ohm on-resistance is useful when switching low-impedance sources, while bidirectional operation permits either an input or output role. The 16-QFN package supports dense layouts where analog routing area is constrained. Check the allowable analog signal range, off-state leakage, and distortion-related characteristics before using it in precision audio paths.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ISL83699IR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ISL83699IR-T |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 16-QFN (3 x 3 mm) | 16-QFN (3 x 3 mm) - same |
| Device Type | Quad SPDT bidirectional analog switch | Quad SPDT bidirectional analog switch |
| Number of Circuits | 4 circuits | 4 circuits |
| Supply Voltage Range | 1.65 V to 3.6 V | 1.65 V to 3.6 V |
| On-Resistance | 0.26 ohm | 0.26 ohm |
| Turn-On Time | 10 ns | 10 ns |
| Turn-Off Time | 7 ns | 7 ns |
| Logic Compatibility | 1.8 V compatible with a single 3 V supply | 1.8 V compatible with a single 3 V supply |
| Signal Direction | Bidirectional | Bidirectional |
主な差別化要因
- Four low-resistance selectors in one compact package (vs ISL83699IR-T)
- Fast source-selection performance (vs ISL83699IR-T)
- Bidirectional signal-path flexibility (vs ISL83699IR-T)
設計ノート
Route each switched signal directly to its assigned QFN terminal and minimize the distance from the source or destination circuitry to the switch. Keep the analog path away from high-current switching nodes and clock edges. Because the device is optimized for 1.65 V to 3.6 V operation, place its supply-decoupling capacitor close to the package supply pins and connect the exposed pad according to the manufacturer land-pattern and thermal guidance.
Include switch on-resistance, off-state leakage, and source or destination input impedance when evaluating signal attenuation. The stated 0.26 ohm on-resistance is low, but it becomes significant when driving a high-impedance measurement node or a long PCB trace. Confirm the usable analog signal range, off-isolation, and switching-time conditions in the manufacturer datasheet for the selected supply voltage.
Do not allow control-pin voltages or analog signal levels to exceed the device limits when powered from 3.3 V or 1.8 V. Prevent conflicting control combinations if the application mutates the selected route, and define a safe state for power-up and reset. Use 1.8 V-compatible control levels with the specified 3 V supply, and confirm the exact ordering suffix and tape-and-reel format before manufacturing release.
コンプライアンス情報
The manufacturer product page states that support is limited to customers who have already adopted these products. No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified.