Renesas Electronics

ISL8485ECB - 5V RS-485/422 Transceiver | Renesas

部品番号: ISL8485ECB ✗ 生産終了
5 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC, 5 mm nominal body width Package Supported up to 5 Mbps Speed
MOQ: 1 |

ISL8485ECB 概要

The Renesas Electronics ISL8485ECB is a 5 V, low-power, half-duplex RS-485/RS-422 line transceiver in an 8-pin SOIC package. It combines one driver and one receiver, supports data rates up to 5 Mbps, and provides ESD protection to ±15 kV HBM. The device is designed for industrial and instrumentation links requiring a compact, high-speed differential transceiver.

A line transceiver is an interface IC that converts logic-level signals into balanced differential signals and receives those differential signals back into CMOS-compatible logic. RS-485 and RS-422 belong to differential data-interface families. Their common-mode rejection and noise immunity make them useful for communications over cables, backplanes, and industrial control networks where signal integrity can be affected by motors, relays, and switching equipment.

The ISL8485ECB operates from a 5 V supply and is identified as a one-driver, one-receiver, half-duplex RS-422/RS-485 device. It can operate as a high-speed transceiver or with slew-rate-limited signaling, allowing the same interface family to address EMC-sensitive links and longer, lower-speed connections. Its 8-pin SOIC package supports surface-mount assembly while retaining a widely used lead pitch.

Electrical performance is centered on a maximum signaling rate of 5 Mbps and low power consumption. The ±15 kV HBM ESD rating protects the device from electrostatic discharge encountered during handling and field installation, although it does not replace proper surge-protection design for an installed cable. The receiver and driver combine in one package, reducing board area in nodes that need bidirectional bus communication.

Typical applications include industrial sensor gateways, programmable logic controller communication, factory automation equipment, test and measurement instruments, building-control nodes, and RS-485 field-bus interfaces. In a half-duplex network, the transceiver can support bus management and point-to-point links when the application controls driver enable and receiver enable states.

For PCB implementation, place the transceiver close to the connector or bus header and keep the differential route short and symmetric. Add the termination, biasing, common-mode protection, and decoupling components recommended by the manufacturer datasheet for the selected bus topology. Confirm driver-enable behavior so multiple transmitters do not contend on the same bus.

This product page combines the manufacturer-device description, verified package and interface details, cross-reference findings, and application-specific design guidance to support faster component evaluation and replacement planning.

ドロップイン代替品: ISL8485ECB — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

ISL8485EIBZ-T

✅ ドロップイン
📦 8-pin SOIC
Same 8-pin SOIC interface and 5 Mbps class, with ordering and temperature-range suffix differences; cross-reference identifies consistent terminals and functional characteristics

📋 参考代替品(カタログ未掲載)

ISL8485ECB 仕様

Product Type RS-485/RS-422 half-duplex line transceiver
電源電圧 5 V
Driver Count 1 driver
Receiver Count 1 receiver
Supported Standards RS-485 and RS-422
Maximum Data Rate 5 Mbps
ESD Protection ±15 kV HBM
Operating Mode Half-duplex
動作温度範囲 0 °C to 70 °C
パッケージ 8-pin SOIC, 5 mm nominal body width
実装タイプ Surface mount
Logic Family CMOS
Driver Configuration 1/1 transceiver
Slew-Rate-Limited Operation Supported
High-Speed Operation Supported up to 5 Mbps

ISL8485ECB 8-pin soic, 5 mm nominal body width ピン配置ガイド

ISL8485ECB (8-pin soic, 5 mm nominal body width パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

ISL8485ECB の 8-pin soic, 5 mm nominal body width パッケージピン配置図

詳細なピン配置データはありません: ISL8485ECB.

詳細は データシート をご参照ください。

主な用途

ISL8485ECB の用途: 6 件s: Industrial Sensor Gateway, PLC Communication Module, Test and Measurement Instrument, Building Control Network, Factory Automation Equipment, Remote Sensor Node.

🏭

Industrial Sensor Gateway

The ISL8485ECB fits a 5 V industrial sensor gateway that must communicate over an RS-485 field bus while also supporting RS-422 links. Its one-driver, one-receiver arrangement covers bidirectional half-duplex nodes, and the 5 Mbps capability provides headroom for aggregated sensor traffic. The ±15 kV HBM rating strengthens handling robustness, but field cables still require external surge protection. Slew-rate-limited operation can also reduce high-frequency emissions when conducted EMI is more restrictive than maximum throughput.

🏭

PLC Communication Module

The ISL8485ECB is appropriate for a programmable logic controller communication module operating from 5 V logic. A single transceiver provides the differential driver and receiver needed for an RS-485 or RS-422 node, while half-duplex control keeps one physical bus usable for command and response traffic. The 5 Mbps maximum rate supports factory automation equipment with short, controlled links. Validate enable timing and termination in the bus controller because concurrent driver activation can produce contention.

🔧

Test and Measurement Instrument

The ISL8485ECB can connect laboratory and field-test instruments to an RS-485 or RS-422 controller using a compact 8-pin SOIC footprint. Its 5 Mbps rate supports high-speed data transfer over properly terminated connections, and the driver-receiver combination simplifies bidirectional command exchange. The low-power 5 V architecture aligns with mixed-signal instrumentation. Keep the differential route away from sensitive analog inputs and use the transceiver's slower slew-rate mode when cable length or radiated-emissions requirements dominate.

🏠

Building Control Network

The ISL8485ECB suits a 5 V building-control node that communicates with sensors, actuators, or distributed controllers over RS-485 or RS-422. Differential signaling supports reliable communication through building wiring where switching loads can introduce interference, and the 8-pin SOIC package limits board footprint. The device's 0 °C to 70 °C operating range suits many indoor environments but must be checked against room and enclosure temperatures. External protection is important at cable entry points.

🏭

Factory Automation Equipment

The ISL8485ECB fits factory automation equipment requiring a compact 5 V differential bus interface for motor controllers, condition-monitoring nodes, or remote I/O. Its one-driver, one-receiver configuration supports half-duplex RS-485 coordination and RS-422 point-to-point links, while 5 Mbps provides substantial throughput for short industrial runs. Use controlled enable logic to prevent bus contention, apply the recommended termination and biasing network, and keep protection devices close to the cable connector.

🧩

Remote Sensor Node

The ISL8485ECB can connect a remote 5 V sensor node to a differential sensor network using either RS-485 multidrop wiring or RS-422 point-to-point wiring. The compact 8-pin SOIC package leaves board area for sensing and conditioning circuitry, and the 5 Mbps capability supports a wide range of digitized measurement traffic. At long distances or near high-energy switching equipment, slew-rate-limited signaling can improve EMC behavior. The cable interface should still include appropriately selected transient-voltage protection.

What is the ISL8485ECB?
The ISL8485ECB is a 5 V, half-duplex RS-485/RS-422 transceiver with one driver and one receiver. According to the manufacturer datasheet, it supports operation up to 5 Mbps and is available in an 8-pin SOIC package. The device can also use slew-rate-limited signaling, giving the same transceiver family options for high-speed links and more noise-tolerant communication.
What is the maximum data rate of ISL8485ECB?
The ISL8485ECB supports data rates up to 5 Mbps. The manufacturer datasheet identifies the device as a high-speed or slew-rate-limited RS-485/RS-422 transceiver operating from a 5 V supply. This rate makes it suitable for industrial links and point-to-point differential connections where signaling speed and bus interoperability are the principal design requirements.
What ESD protection does ISL8485ECB provide?
The ISL8485ECB provides ESD protection rated to ±15 kV HBM. The manufacturer datasheet describes this protection for the device's external bus interface. The rating improves handling robustness during assembly and service, but it does not eliminate the need for correctly selected cable protection, grounding, and surge-suppression components in industrial installations.
What package does ISL8485ECB use?
The ISL8485ECB uses an 8-pin SOIC package for surface-mount assembly. The 8-SOIC package is also identified by the manufacturer listing as PDSO8. Before laying out a replacement PCB, verify the lead pitch, body dimensions, pin numbering, and exposed-thermal-pad status against the current manufacturer package drawing.
Where can I find the ISL8485ECB datasheet and pinout?
The ISL8485ECB datasheet is available through the manufacturer-document link listed on this page and through the Intersil datasheet archive. Use the pin-description table and package drawing in that document when assigning PCB tracks. The component is an 8-pin SOIC, so the complete eight-position connection list must be compared with the board before assembly.
ISL8485ECB vs ISL8485EIBZ-T - which is the better drop-in choice?
ISL8485EIBZ-T is a drop-in alternative for ISL8485ECB because the cross-reference describes consistent terminals, package, and functional characteristics. Both devices are 8-pin SOIC RS-485/RS-422 transceivers, but the temperature-range and ordering suffixes must still be checked against the original assembly requirements before production release. The alternative is listed from web cross-reference information.
When should I choose ISL8485ECB over a lower-speed RS-485 transceiver?
Choose ISL8485ECB when the link requires a 5 V half-duplex RS-485/RS-422 interface operating as high as 5 Mbps. Compared with lower-speed transceivers, its principal benefit is signaling rate while retaining one driver, one receiver, and an 8-pin SOIC footprint. For long cables or electrically noisy installations, assess whether the slower slew-rate-limited mode provides better EMI behavior.
Is ISL8485ECB suitable for industrial sensor and PLC networks?
The ISL8485ECB is suitable for industrial sensor and PLC links that use 5 V RS-485 or RS-422 signaling and require up to 5 Mbps operation. Its differential interface supports noise-tolerant field-bus communication, while the half-duplex arrangement fits nodes with controlled driver-enable logic. The 0 °C to 70 °C rating must remain within the enclosure's specified temperature range.
What is the best drop-in replacement for ISL8485ECB?
ISL8485EIBZ-T is the directly identified drop-in alternative because it uses the same 8-pin SOIC format and is described as functionally and pin compatible. Its 5.5 V and 5 Mbps ratings support close parameter equivalence, although ordering suffix, temperature grade, and exact exposed-pad construction should be confirmed against the approved manufacturer documentation before substitution.
What can replace ISL8485ECB without changing the PCB?
ISL8485EIBZ-T can replace ISL8485ECB without a PCB footprint change according to the cross-reference result. Both use an 8-pin SOIC and implement a one-driver, one-receiver RS-485/RS-422 interface. Review enable timing, receiver thresholds, bus loading, thermal performance, and lifecycle requirements to confirm that package compatibility is also acceptable system-level compatibility.
Where can I buy ISL8485ECB online?
Use the Request a Quote form on this page to ask about ISL8485ECB availability, current lead time, minimum order quantity, and package delivery options. Because this is an obsolete catalog part, supply and lifecycle status should be confirmed for the exact suffix before a purchase order is released. The form avoids reliance on stale listing information.
What is the price of ISL8485ECB?
Request the current ISL8485ECB price through the Request a Quote form on this page. The structured listing records an archived unit-price reference for this exact MPN, but the request process provides a fresher quotation tied to quantity, condition, and delivery requirements. No static customer price should be used as the basis for a production procurement decision.
What is the lead time for ISL8485ECB?
The current lead time for ISL8485ECB should be confirmed through the Request a Quote form on this page. Because the device is cataloged as obsolete, availability may depend on remaining factory or channel inventory rather than normal production scheduling. Include the required quantity, date code preference, and destination when requesting the quotation.
Is ISL8485ECB in stock?
Request current ISL8485ECB inventory status through the Request a Quote form on this page. The part is categorized as obsolete, so historical stock indications do not establish present availability for the exact 8-pin SOIC suffix. A supplier should confirm live inventory, traceability, date codes, and shipping quantity before the component enters a build schedule.
What are the key specifications engineers should know about ISL8485ECB?
The key ISL8485ECB specifications are a 5 V supply, one-driver/one-receiver half-duplex operation, RS-485 and RS-422 support, a maximum rate of 5 Mbps, ±15 kV HBM ESD protection, and an 8-pin SOIC package. According to the manufacturer datasheet, the device can operate with high-speed or slew-rate-limited drive, allowing designers to balance throughput against electromagnetic-interference behavior.
Is ISL8485ECB the same as MAX485CSA?
The ISL8485ECB and MAX485CSA serve the same broad RS-485 interface category, but they should not be treated as automatically identical drop-in parts. A direct substitution requires confirmation of package geometry, pin functions, supply voltage, driver and receiver enable logic, data rate, ESD rating, and temperature range. The available comparison identifies both devices as candidates for evaluation rather than proving every operating parameter is identical.

エンジニアリング参考データ: ISL8485ECB — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose ISL8485ECB when the design needs a 5 V, half-duplex RS-485 or RS-422 transceiver in an 8-pin SOIC package and supports signaling rates as high as 5 Mbps. It is particularly suitable for compact industrial, test-instrument, building-control, and factory-automation nodes that need both high-speed operation and a documented ±15 kV HBM ESD rating. Consider ISL8485EIBZ-T when the same mechanical and functional replacement path is desired, but verify its exact temperature grade, ordering suffix, and lifecycle conditions before releasing it to production. MAX485CSA may be considered only after checking package pins, enable polarity, data rate, and protection requirements; similarity in RS-485 function does not establish drop-in compatibility. For new designs, also evaluate current transceiver families with lifecycle support and application-specific protection rather than assuming an obsolete part is the lowest-risk production choice.

代替品との比較

パラメータ この製品 ISL8485EIBZ-T
Package 8-pin SOIC 8-pin SOIC
Brand Renesas Electronics Renesas Electronics
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver
Supply Voltage 5 V 5.5 V
Maximum Data Rate 5 Mbps 5 Mbps
Driver and Receiver Count 1 driver, 1 receiver 1 driver, 1 receiver
Operating Mode Half-duplex Half-duplex

主な差別化要因

  • Higher-rate RS-485/RS-422 interface option (vs MAX485CSA)
  • Direct 8-pin SOIC pin-compatible path (vs ISL8485EIBZ-T)
  • Field-handling ESD protection (vs ISL8485EIBZ-T)

設計ノート

Route the RS-485 and RS-422 differential pair as a tightly coupled pair with a continuous ground reference, and terminate the transceiver at the connector side of the board. Keep the pair away from switching nodes, relay coils, crystal circuits, and high-current power paths. Use symmetric component placement around the transceiver so parasitic mismatch remains small. Follow the manufacturer's pin-description table for every connection.

Do not enable the driver while another node is transmitting on the same bus. Half-duplex implementations need deterministic driver-enable and receiver-enable control, including enough dead time to prevent contention. Confirm that any system alternative uses the same enable polarity and timing. For long or noisy cables, add external surge protection and evaluate the slower slew-rate mode rather than relying on the internal ESD rating for installation transients.

Place the required 5 V decoupling capacitor immediately beside the transceiver's supply and ground pins, with a short return path to the ground plane. The supply must remain within the device's operating limits during bus transients and startup. Avoid sharing a narrow supply-current path with relay drivers, motors, or other switching loads because disturbance on the 5 V rail can cause receiver errors even when the differential bus itself is well terminated.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for this legacy device.

データ検証日: 2026-11-20 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

ISL8485ECB datasheet ISL8485ECB pinout ISL8485ECB datasheet pdf ISL8485ECB equivalent ISL8485ECB replacement ISL8485ECB cross reference ISL8485ECB footprint ISL8485ECB price ISL8485ECB stock Renesas ISL8485ECB ISL8485ECB 5 Mbps RS-485 ISL8485ECB vs ISL8485EIBZ-T ISL8485ECB industrial application 8 pin SOIC RS-485 transceiver

関連部品&用語

Renesas Electronics Intersil ISL8485ECB ISL8485EIBZ-T MAX485CSA RS-485 RS-422 half-duplex transceiver differential line transceiver interface IC CMOS 5 Mbps 5 V power supply ESD protection HBM slew-rate limiting 8-pin SOIC PDSO8 surface-mount package industrial automation sensor gateway field-bus communication surge protection common-mode rejection
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示