Renesas Electronics

ISL8487IPZ - 250kbps RS-485/422 Transceiver | Renesas

部品番号: ISL8487IPZ ✓ 生産中
5 V Vdss 8-pin PDIP, MS-001BA Package
MOQ: 1 |

ISL8487IPZ 概要

Renesas Electronics ISL8487IPZ is a single RS-485/RS-422 half-duplex transceiver operating from a 5 V supply, with one driver and one receiver, a 250 kbps data rate, and a fractional 1/8 unit-load receiver in an 8-pin PDIP package. The device is designed for balanced industrial communication links requiring ESD protection to ±15 kV.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus signals and receives differential bus signals back into CMOS-compatible logic. The ISL8487IPZ belongs to the transceiver hierarchy of RS-422/RS-485 interface ICs, supporting robust point-to-point or multipoint communication over cables and printed-circuit-board interconnects. Its differential signaling improves common-mode noise rejection compared with single-ended digital interfaces.

Key features include support for both RS-485 and RS-422 protocols, 4.5 V to 5.5 V supply operation, 70 mV receiver hysteresis, and a 1/8 unit-load receiver input. The 1/8 unit-load rating allows more receivers to share a bus than a conventional quarter-unit-load receiver. ESD protection of ±15 kV improves interface resilience in industrial environments where cables can be exposed to electrostatic discharge.

The BiCMOS implementation combines bipolar interface characteristics with CMOS-compatible logic operation. A half-duplex architecture allows the driver and receiver to share a differential pair, reducing wiring in two-wire networks. The 250 kbps signaling rate supports moderate-speed industrial control, automation, instrumentation, and embedded data links while retaining compatibility with established RS-485 and RS-422 equipment.

Typical uses include factory automation controllers, process-monitoring equipment, sensor networks, industrial data acquisition, building controls, and embedded systems communicating with remote peripherals. The device is particularly useful where low power, a fractional unit load, ESD protection, and a through-hole 8-pin PDIP package are important design priorities.

PCB design should preserve the recommended differential trace geometry and provide a low-impedance return path. Bus termination, biasing, protection, and grounding should be selected for the cable length, topology, and environmental conditions. The ISL8487IPZ is a general-purpose interface device rather than a power component, so thermal analysis centers on surrounding circuitry and bus fault energy rather than the transceiver junction alone.

This product page combines package information, interface characteristics, drop-in replacement guidance, application-oriented circuit guidance, and a parameter comparison to help engineers evaluate transceiver selection and board-level implementation.

ドロップイン代替品: ISL8487IPZ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: ISL8487IPZ (同一形状・フットプリント) — 相違点: Duplex Mode, Package.

Renesas Electronics
Duplex Mode: Half-duplex
Package: 8-pin PDIP
比較対象 ISL8487IPZ →

ISL8487EIPZ

✅ ドロップイン
📦 8-PDIP
Uses the same 8-PDIP footprint and single half-duplex RS-485/RS-422 topology; the E-version speed and slew-rate option differs from the ISL8487IPZ

📋 参考代替品(カタログ未掲載)

MAX487CPA+

✅ ドロップイン
📦 8-PDIP
Receiver load is 1/4 unit versus 1/8 unit on the ISL8487IPZ, reducing the conventional bus-node budget by 50%; data rate remains in the 250 kbps class

📋 参考代替品(カタログ未掲載)

ISL8487IPZ 仕様

Product Type RS-485/RS-422 half-duplex transceiver
Technology BiCMOS
電源電圧 5 V
Operating Supply Voltage Range 4.5 V to 5.5 V
Number of Drivers 1 driver
Number of Receivers 1 receiver
Supported Protocols RS-422 and RS-485
Duplex Mode Half duplex
Maximum Data Rate 250 kbps
Receiver Unit Load 1/8 unit load
Receiver Hysteresis 70 mV
ESD Protection ±15 kV
動作温度範囲 -40°C to +85°C
パッケージ 8-pin PDIP, MS-001BA
Package Pitch 7.62 mm
実装タイプ Through hole
Standard Packaging Tube

ISL8487IPZ 7.62 mm ピン配置ガイド

ISL8487IPZ (7.62 mm パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

ISL8487IPZ の 7.62 mm パッケージピン配置図

詳細なピン配置データはありません: ISL8487IPZ.

詳細は データシート をご参照ください。

主な用途

ISL8487IPZ の用途: 6 件s: Factory Automation Controller Networks, Industrial Sensor Data Acquisition, Process Monitoring Equipment, Building and HVAC Control Links, Instrumentation and Test Equipment, Embedded RS-485 Communication Ports.

🏭

Factory Automation Controller Networks

The ISL8487IPZ fits factory automation links that distribute commands and sensor readings over balanced cable pairs at data rates up to 250 kbps. Its 1/8 unit-load receiver allows more monitoring nodes to share a bus than a quarter-unit-load receiver, while 70 mV hysteresis helps reject noise from nearby motor drives and switching equipment. Place the transceiver at a cable entry point, follow the datasheet bias and termination recommendations, and provide a low-impedance ground reference. The 250 kbps limit should be checked against total cable length and the number of nodes.

🧩

Industrial Sensor Data Acquisition

The ISL8487IPZ is suitable for sensor networks where a central controller reads distributed measurements over an RS-485 bus. Differential signaling reduces susceptibility to common-mode voltage, and the 1/8 unit load reduces bus loading so more remote sensing nodes can operate without exceeding the driver budget. Its ±15 kV ESD protection is valuable where field cables may be touched during installation or maintenance. Designers should still assess whether longer cables require additional surge protection and verify that the complete system remains within the 250 kbps signaling limit.

📺

Process Monitoring Equipment

The ISL8487IPZ supports process-monitoring equipment that exchanges pressure, temperature, and valve-status information between a control panel and remote instrumentation. The 5 V operating range fits conventional embedded logic supplies, while the single-driver, single-receiver arrangement simplifies a two-wire half-duplex implementation. Its fractional unit load permits denser instrument networks than a 1/4 unit-load transceiver. Use differential routing with consistent impedance, provide fail-safe biasing at one designated location, and confirm that grounding arrangements avoid injecting noise into the reference plane.

🏠

Building and HVAC Control Links

The ISL8487IPZ can connect HVAC controllers, room modules, dampers, and environmental sensors through an RS-485 network. Building-control cables often pass near relays, lighting electronics, and variable-frequency equipment, making the receiver's 70 mV hysteresis and ±15 kV ESD protection useful. The 1/8 unit-load receiver allows multiple room controllers to share a bus, provided the calculated load remains below the allowed total. Use the device as a bus transceiver rather than an isolated interface when ground-offset limits would be exceeded.

🔧

Instrumentation and Test Equipment

The ISL8487IPZ is appropriate for bench and field instrumentation that needs a reliable differential link to external fixtures or remote measurement equipment. A 250 kbps data rate is sufficient for many command and status protocols, while the 1/8 unit load permits several low-power receiving sections to monitor the same bus. The PDIP package is straightforward to prototype, repair, and socket where appropriate. For laboratory systems with long unshielded leads, add suitable surge protection and verify connector shields and ground references before energizing the interface.

⚡

Embedded RS-485 Communication Ports

The ISL8487IPZ adds a standard industrial communication port to an embedded controller or data logger. One driver and one receiver are sufficient for a two-wire half-duplex bus, while the fractional receiver load supports multi-drop field networks. The 5 V supply operation and 8-pin PDIP format simplify integration with through-hole controller boards and legacy equipment. Firmware must manage bus direction, prevent simultaneous transmission, and include timeout handling so a disabled driver cannot hold the line in an active state.

おすすめ製品の概要

ISL8487EIPZ Same-manufacturer 8-PDIP transceiver alternative 使用用途: Factory Automation Controller Networks, Industrial Sensor Data Acquisition, Process Monitoring Equipment, Building and HVAC Control Links, Instrumentation and Test Equipment, Embedded RS-485 Communication Ports MAX487CPA+ Single-driver, single-receiver RS-485 transceiver alternative 使用用途: Factory Automation Controller Networks, Industrial Sensor Data Acquisition, Process Monitoring Equipment, Building and HVAC Control Links, Instrumentation and Test Equipment, Embedded RS-485 Communication Ports
What is the ISL8487IPZ?
The ISL8487IPZ is a Renesas Electronics single-channel RS-485/RS-422 half-duplex transceiver with one driver and one receiver. According to the manufacturer datasheet, it uses BiCMOS technology, operates from a 5 V supply, supports signaling up to 250 kbps, and is packaged in an 8-pin PDIP. It is intended for balanced data links requiring differential noise rejection and limited bus loading.
What are the key specifications of ISL8487IPZ that engineers should know?
The ISL8487IPZ combines a 4.5 V to 5.5 V supply range with a maximum data rate of 250 kbps. The manufacturer datasheet identifies a 1/8 unit-load receiver, 70 mV receiver hysteresis, ±15 kV ESD protection, one driver, one receiver, and half-duplex RS-485/RS-422 operation. These characteristics make the device suitable for moderate-speed industrial links with multiple attached receivers and exposed cabling.
What is the operating voltage of ISL8487IPZ?
The ISL8487IPZ operates from a nominal 5 V supply with a specified range of 4.5 V to 5.5 V. According to the manufacturer datasheet, the device is a single RS-485/RS-422 transceiver rather than a modern multi-level supply interface IC. The design should therefore be powered from a regulated rail that remains within the specified 5 V range under transient conditions.
How fast is the ISL8487IPZ RS-485 transceiver?
The ISL8487IPZ supports a maximum data rate of 250 kbps. The manufacturer datasheet describes it as a low-power, high-speed or slew-rate-limited RS-485/RS-422 transceiver. Its 250 kbps rating is appropriate for industrial control links, sensors, and data-acquisition systems, but it is not intended for the multi-megabit rates commonly required by modern high-speed Ethernet or video interfaces.
Why is the 1/8 unit load of ISL8487IPZ important?
The ISL8487IPZ presents a 1/8 unit load to the RS-485 bus, allowing up to eight receiver loads on one bus under standard unit-load budgeting. The manufacturer datasheet identifies this fractional-load capability as a defining feature. It is useful in distributed industrial networks where several protected or isolated nodes must monitor the same differential pair without overloading the bus driver.
What does the 70 mV receiver hysteresis of ISL8487IPZ provide?
The 70 mV receiver hysteresis provides noise margin between the differential output states of the bus driver. According to the manufacturer datasheet, this helps prevent the receiver from changing state when small voltage disturbances appear around the threshold. The feature is especially useful on cables running near motors, switching equipment, or other industrial sources of transient noise.
What package and pin count does the ISL8487IPZ use?
The ISL8487IPZ uses an 8-pin plastic PDIP designated MS-001BA with a 7.62 mm lead pitch. The manufacturer datasheet describes the device as a through-hole component, while catalog information identifies tube packaging. The package is distinct from the surface-mount alternatives commonly offered for the same RS-485 function, so PCB footprint compatibility must be confirmed before substitution.
Where can I download the ISL8487IPZ datasheet PDF?
The ISL8487IPZ datasheet can be downloaded from the Renesas/Intersil document listing identified on the component datasheet page. It covers the 5 V BiCMOS architecture, RS-485 and RS-422 operation, electrical characteristics, receiver thresholds, ESD ratings, and application information. Use the pin-description table and typical application circuit in that document when assigning PCB signals and external components.
Where can I find the ISL8487IPZ pinout?
The ISL8487IPZ pin assignments are defined by the pin-description table in the Renesas/Intersil manufacturer datasheet. The device uses an 8-pin PDIP with differential driver and receiver connections, a receiver-enable control, and supply and ground pins. Assign tracks from the datasheet pin table rather than inferring connections solely from the protocol, since enable polarity and exposed driver/receiver pins must match the selected operating mode.
What can replace the ISL8487IPZ?
The ISL8487EIPZ is the closest same-manufacturer alternative identified for the ISL8487IPZ because it uses the same 8-pin PDIP format and is described as a complete replacement candidate. The MAX487CPA+ is a cross-brand 8-pin PDIP alternative with similar RS-485/RS-422 functionality. Before substitution, compare data rate, receiver unit load, enable logic, supply range, ESD rating, and package dimensions against the original design.
IS the ISL8487IPZ the same as the MAX487CPA+?
The ISL8487IPZ and MAX487CPA+ both provide a single RS-485/RS-422 transceiver in an 8-pin PDIP, but they are not identical in every electrical parameter. The ISL8487IPZ has a 1/8 unit load, 250 kbps data rate, 70 mV hysteresis, and ±15 kV ESD protection according to its datasheet. The MAX487CPA+ uses a 1/4 unit load, so the number of receiver nodes permitted on a shared bus must be recalculated.
ISL8487IPZ vs ISL8487EIPZ - which is better for a legacy through-hole design?
The ISL8487EIPZ is the more direct choice for a legacy through-hole board because cross-reference information identifies it as an 8-PDIP replacement for the ISL8487IPZ. The target ISL8487IPZ offers a 1/8 unit load, 250 kbps data rate, and ±15 kV ESD protection, but the exact enable behavior and speed option must still be checked. Both options should be validated against the original schematic and bus-bias network.
When should I choose ISL8487IPZ over MAX487CPA+?
Choose the ISL8487IPZ when the bus must support more receiver nodes or when its ±15 kV ESD rating is central to the installation. The target device uses a 1/8 unit load, allowing up to eight standard receiver loads, while the MAX487CPA+ uses a 1/4 unit load and therefore halves the conventional unit-load budget. Both are single half-duplex transceivers in an 8-pin PDIP, so bus topology and node count are the decisive factors.
Is ISL8487IPZ suitable for industrial automation and sensor networks?
Yes, the ISL8487IPZ is suitable for industrial automation and sensor-network links operating at 250 kbps or lower. Its differential RS-485/RS-422 interface, 1/8 unit-load receiver, 70 mV hysteresis, and ±15 kV ESD protection support reliable communication over longer cable runs than a single-ended interface. The final design must still include suitable termination, fail-safe biasing, grounding, and surge protection for the installation environment.
Where can I buy ISL8487IPZ online?
Use the Request a Quote form on this page to request ISL8487IPZ availability, current pricing, minimum order quantity, and lead time. The form is the appropriate channel for obtaining a quotation for the exact 8-pin PDIP order code. Confirm the requested package suffix, tube packaging, and lifecycle status before placing a production order, especially when the same transceiver function is available in several different packages.
What is the price of ISL8487IPZ?
Current pricing for ISL8487IPZ should be requested through the Request a Quote form on this page because distributor price breaks and inventory change frequently. Specify the exact ISL8487IPZ order code, quantity, tube packaging requirement, and target delivery date when requesting the quotation. This ensures the response applies to the 8-pin PDIP device rather than a related RS-485 transceiver with a different package or suffix.
What is the lead time for ISL8487IPZ?
The current lead time for ISL8487IPZ should be confirmed through the Request a Quote form on this page. Lead time can vary with manufacturer inventory, quantity, package configuration, and incoming supply conditions, so a historical catalog figure is not a reliable production commitment. Ask the supplier to state the quantity available, expected delivery date, and whether any scheduled shipment allocation applies to your order.

エンジニアリング参考データ: ISL8487IPZ — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the ISL8487IPZ when the design needs a 5 V RS-485/RS-422 interface with a 1/8 unit-load receiver, 250 kbps operation, 70 mV hysteresis, and ±15 kV ESD protection. Its fractional loading is especially useful when more than four conventional receiver nodes share a bus. Select the ISL8487EIPZ when its exact speed and slew-rate behavior better matches the original circuit while retaining the 8-PDIP footprint. Consider the MAX487CPA+ when the lower node count of its 1/4 unit-load receiver is acceptable and the remaining electrical characteristics meet the application. Before any substitution, compare supply limits, receiver thresholds, enable timing, ESD rating, bus topology, and package dimensions; matching an 8-pin DIP outline alone does not guarantee equivalent operation.

代替品との比較

パラメータ この製品 ISL8487EIPZ MAX487CPA+
Manufacturer Renesas Electronics Renesas Electronics Maxim Integrated
Package 8-PDIP 8-PDIP - same 8-PDIP - same
Transceiver Configuration 1 driver / 1 receiver 1 driver / 1 receiver 1 driver / 1 receiver
Supported Protocols RS-422 and RS-485 RS-422 and RS-485 RS-422 and RS-485
Duplex Mode Half duplex Half duplex Half duplex
Nominal Supply Voltage 5 V 5 V 5 V
Maximum Data Rate 250 kbps 250 kbps class 250 kbps class

主な差別化要因

  • Lower bus loading supports denser networks (vs MAX487CPA+)
  • Defined industrial ESD protection (vs MAX487CPA+)
  • Through-hole package continuity within the Renesas family (vs ISL8487EIPZ)

設計ノート

Route the differential pair as a controlled-impedance pair and keep the driver, receiver, protection devices, and optional termination close together. Avoid stubs and sharply divergent traces because reflected signals can distort the receiver threshold at 250 kbps. Provide a continuous ground reference beneath the interface and separate the transceiver ground connection from noisy power-return paths where the layout permits.

Do not assume every 8-PDIP RS-485 transceiver has the same receiver loading. The ISL8487IPZ presents a 1/8 unit load, while the MAX487CPA+ presents a 1/4 unit load, reducing the conventional maximum receiver count by 50%. Recalculate the total bus load and verify enable polarity, driver-disable behavior, and fail-safe biasing before using either part as a production replacement.

Install termination only where it belongs in the network topology, and apply fail-safe bias at one carefully selected location rather than at every node. For exposed field cables, add appropriately rated surge and ESD protection with a short return path to ground. Keep protection switching transients away from the receiver inputs and verify that added protection capacitance does not degrade the intended 250 kbps signal rate.

Use the manufacturer pin-description table to assign the 8-pin PDIP connections and preserve the documented receiver-enable and driver-control functions. A through-hole package does not remove the need for controlled bus geometry: keep outgoing cable stubs short, maintain clearance from switching nodes, and verify the ground reference at both ends of the cable. The device is not an isolated interface, so system ground offsets must remain within the intended operating range.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The manufacturer documentation excerpt identifies BiCMOS technology and ±15 kV ESD protection but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.

データ検証日: 2026-11-20 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

ISL8487IPZ datasheet ISL8487IPZ pinout ISL8487IPZ datasheet pdf ISL8487IPZ equivalent ISL8487IPZ replacement ISL8487IPZ cross reference ISL8487IPZ vs MAX487CPA+ ISL8487IPZ vs ISL8487EIPZ ISL8487IPZ 250kbps transceiver ISL8487IPZ PDIP-8 pinout Renesas ISL8487IPZ ISL8487IPZ price ISL8487IPZ stock ISL8487IPZ RS-485 application circuit

関連部品&用語

Renesas Electronics Intersil ISL8487IPZ ISL8487EIPZ MAX487CPA+ RS-485 transceiver RS-422 transceiver half-duplex transceiver interface IC BiCMOS differential signaling common-mode rejection 1/8 unit load 70 mV receiver hysteresis 250 kbps data rate ESD protection ±15 kV ESD protection 8-pin PDIP MS-001BA package through-hole mounting industrial automation sensor network process monitoring building control field-bus communication
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示