ISO1540D - 2.5kVrms I2C Digital Isolator | Texas Instruments
部品番号: ISO1540D ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $3.85 | $3.85 |
| 10 | $3.47 | $34.70 |
| 100 | $2.95 | $295.00 |
| 500 | $2.55 | $1,275.00 |
| 1,000 | $2.2 | $2,200.00 |
ISO1540D 概要
A digital isolator transfers digital signals across an isolation barrier, preventing DC and ground-loop current flow while allowing data to pass. Digital isolators are core building blocks in power management hierarchies, replacing optocouplers with higher speed, better reliability, longer life, and smaller footprint. The ISO1540D specifically addresses I2C buses, whose open-drain, bidirectional clock and data lines require specialized direction-handling logic that general-purpose digital isolators cannot provide.
Key features include bidirectional SCL and SDA channels that isolate the I2C bus without external direction control, 1-MHz (fast-mode) operation, and 25kV/us common-mode transient immunity (CMTI) for robust operation in noisy power environments. The open-drain outputs integrate directly into standard I2C topologies with external pull-up resistors on both sides of the barrier.
Technically, the ISO1540D uses TI capacitive isolation technology with a silicon dioxide (SiO2) barrier, delivering high isolation robustness and long-term reliability with a typical propagation delay of 67ns, preserving I2C timing margins. The wide 3V to 5.5V supply range allows 3.3V-to-5V logic domain crossing across the barrier.
Typical applications include isolated I2C sensor interfaces in industrial automation, battery management systems (BMS), power supplies, motor drives, and medical monitoring equipment, where the ISO1540D separates control electronics from high-voltage or noisy power stages.
Design tip: size pull-up resistors on both sides according to bus capacitance and the 1-Mbps data rate, and place 0.1uF decoupling capacitors close to both supply pins, as current pricing of roughly $2 to $4 per unit (as of 2026-08-29) makes it cost-effective to use one isolator per isolated bus segment.
ドロップイン代替品: ISO1540D — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ISO1540D （同一形状・フットプリント） — 相違点: Number of Channels, Data Rate, Supply Voltage Range, Package, Propagation Delay.
クイック比較ツール — 並列比較する代替部品を選択:
ISO1541D
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ISO1540QDQ1
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ISO1540DR
✅ ドロップイン📋 参考代替品（カタログ未掲載）
ADUM1250ARZ
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$1.85 / 個
データシートを見る →ADUM1251ARZ
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$4.23 / 個
データシートを見る →ISO1540D 仕様
| Isolation Type | Bidirectional I2C isolator |
| Number of Channels | 2 (SCL, SDA) |
| Isolation Voltage | 2500 Vrms |
| データレート | 1 Mbps (1 MHz I2C fast-mode) |
| CMTI | 25 kV/us |
| Supply Voltage Range | 3 V to 5.5 V |
| Propagation Delay | 67 ns (typical) |
| Side 1 Sink Current | 3.5 mA |
| Side 2 Sink Current | 35 mA |
| 出力タイプ | Open-drain |
| 動作温度 | -40C to +125C |
| パッケージ | 8-SOIC (0.154in, 3.90mm width) |
| 実装タイプ | Surface Mount |
| Isolation Technology | Capacitive, SiO2 barrier |
| RoHS ステータス | Compliant |
ISO1540D ピン構成
| ピン 1 | VCC1 — Side 1 supply, 3V to 5.5V |
| ピン 2 | GND1 — Side 1 ground reference |
| ピン 3 | SCL1 — Side 1 serial clock, open-drain, bidirectional |
| ピン 4 | SDA1 — Side 1 serial data, open-drain, bidirectional |
| ピン 5 | SDA2 — Side 2 serial data, open-drain, bidirectional |
| ピン 6 | SCL2 — Side 2 serial clock, open-drain, bidirectional |
| ピン 7 | GND2 — Side 2 ground reference (isolated) |
| ピン 8 | VCC2 — Side 2 supply, 3V to 5.5V (isolated) |
主な用途
ISO1540D の用途: 6 件s: Battery Management Systems (BMS), Industrial Automation Sensor Interfaces, Isolated Power Supply Telemetry, Motor Drive Control, Medical Monitoring Equipment, 3.3V to 5V I2C Logic Domain Crossing.
Battery Management Systems (BMS)
The ISO1540D isolates the I2C bus between battery cell monitors and the system controller in battery management systems. Its 2500Vrms isolation blocks pack-level voltages, and 25kV/us CMTI tolerates switching transients from adjacent power converters. Placed between the BQ769x0 monitor I2C bus and the MCU with 1k to 4.7k pull-ups on both sides, it transfers SCL and SDA bidirectionally without direction control. The -40C to +125C range supports automotive and industrial pack environments, and the 3V to 5.5V supply range allows 3.3V MCU domains to communicate with 5V monitoring domains across the barrier.
おすすめ
Industrial Automation Sensor Interfaces
In industrial automation, I2C sensors and ADCs often sit near motors, relays, and high-voltage rails that inject ground noise. The ISO1540D provides a 2500Vrms galvanic barrier with 25kV/us CMTI so transients on the factory floor do not corrupt data or damage the controller. Its 67ns propagation delay keeps I2C timing margins intact at 400kHz and 1MHz fast-mode operation. The open-drain outputs integrate directly into standard I2C topologies with pull-ups on each side, allowing isolated sensor clusters to share one controller without ground loops between equipment chassis.
おすすめ
Isolated Power Supply Telemetry
Switching power supplies and DC-DC modules use I2C power monitors for telemetry, but the controller must remain isolated from the primary or hot-swap domain. The ISO1540D bridges the barrier with 2500Vrms isolation and 1Mbps speed, fast enough for periodic polling of voltage, current, and temperature registers on INA-class monitors. Its 25kV/us CMTI withstands the high dv/dt of power stages, and the 3V to 5.5V supply range lets both sides run at their native rails. Two 0.1uF decoupling capacitors, one per side, plus appropriately sized pull-ups complete the design.
おすすめ
Motor Drive Control
Motor drives place gate drivers and current-sensing circuitry at high common-mode potentials that swing rapidly during PWM switching. The ISO1540D isolates the I2C configuration and status bus between the controller and drive electronics, with 25kV/us CMTI preventing PWM dv/dt transients from toggling the data lines. The 2500Vrms working barrier covers typical 400V-class drive isolation budgets, and the -40C to +125C operating range suits drive enclosures. Its bidirectional channels let the controller both configure registers and read fault flags over the same two-wire bus without extra direction signals.
おすすめ
Medical Monitoring Equipment
Medical monitoring equipment requires patient-isolation barriers on all interfaces touching sensor front ends. The ISO1540D provides 2500Vrms galvanic isolation for I2C connections between isolated analog front ends and the main processor board, helping designs meet isolation requirements while keeping the digital interface simple. Its capacitive SiO2 barrier avoids optocoupler aging and LED degradation, supporting long service life in clinical devices. The 3V to 5.5V supply range and low-power operation suit battery-powered portable monitors, while 1Mbps operation keeps sampling-control loops responsive.
おすすめ
3.3V to 5V I2C Logic Domain Crossing
Many mixed-rail systems must connect a 3.3V microcontroller I2C bus to a 5V peripheral domain. The ISO1540D solves this natively: each side is powered independently from 3V to 5.5V, so Side 1 at 3.3V can communicate with Side 2 at 5V without separate level shifters. The open-drain outputs pull to each side's local rail, preserving valid logic levels on both buses. Compared with passive level-shift schemes, it simultaneously provides the 2500Vrms isolation and 25kV/us CMTI needed when the peripheral domain sits on a noisy or floating ground.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ISO1540D — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ISO1541D | ISO1540QDQ1 | ADuM1250ARZ |
|---|---|---|---|---|
| Package | 8-SOIC (0.154in, 3.90mm) | 8-SOIC (0.154in, 3.90mm) - same | 8-SOIC (0.154in, 3.90mm) - same | 8-SOIC - verify pinout |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices |
| Isolation Voltage | 2500 Vrms | 2500 Vrms | 2500 Vrms | 2500 Vrms |
| Clock Channel Direction | Bidirectional | Unidirectional | Bidirectional | Bidirectional |
| Data Rate | 1 Mbps | 1 Mbps | 1 Mbps | 1 Mbps |
| Automotive Grade | No | No | Yes (AEC-Q100) | No |
| Supply Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3.0 V to 5.5 V |
主な差別化要因
- Bidirectional clock channel for multi-master and clock-stretching I2C （vs ISO1541D)
- Automotive-grade variant available on identical footprint （vs ISO1540QDQ1)
- TI capacitive SiO2 isolation with verified 25kV/us CMTI （vs ADuM1250ARZ)
設計ノート
Both SCL and SDA on each side of the ISO1540D require external pull-up resistors because the outputs are open-drain (3.5mA sink on Side 1, 35mA on Side 2). For 400kHz to 1MHz buses, use 1k to 2.2k pull-ups on both sides; for slower or higher-capacitance buses, 4.7k to 10k reduces static current. Refer to the TI ISO154x datasheet application section for pull-up sizing versus bus capacitance.
VCC1 and VCC2 are on separate, isolated domains and must each be decoupled with a 0.1uF ceramic capacitor placed within 2mm of the corresponding supply pin, plus a bulk capacitor if the local rail is shared with noisy loads. If one side is unpowered, the ISO1540D presents a high-impedance default state on that side, which supports hot-swap and multi-master I2C topologies.
Do not substitute the ISO1541D for the ISO1540D on multi-master buses or where clock stretching is used - the ISO1541D's unidirectional clock channel will lock up the bus. Also keep the isolated Side 2 ground return away from high dv/dt power-stage traces; although CMTI is 25kV/us, coupling into long isolated traces degrades signal integrity at 1MHz operation.
コンプライアンス情報
RoHS compliant per distributor listings. AEC-Q100 qualification applies only to the ISO1540QDQ1 variant; the standard ISO1540D is not automotive qualified. Other compliance details not stated in provided data.
