K32W061Z - Multiprotocol Wireless MCU 802.15.4/BLE 5.0 | NXP
部品番号: K32W061Z ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $8.36 | $8.36 |
| 10 | $7.69 | $76.90 |
| 100 | $6.45 | $645.00 |
| 500 | $5.72 | $2,860.00 |
| 1,000 | $5.18 | $5,180.00 |
K32W061Z 概要
A wireless MCU (system-on-chip) is a category of integrated circuit that combines an application-class microcontroller with one or more radio transceivers on a single die. The K32W061Z sits within the hypernym hierarchy wireless MCU -> RF SoC -> short-range radio IC -> semiconductor -> integrated circuit. In system-level power architecture, it typically draws from a DC-DC converter or low-Iq regulator, occupies the application-layer role of a Thread Border Router node, a Zigbee Coordinator/End Device, a BLE 5.0 peripheral/central, or a Matter-over-Ready controller, and is commonly selected when designers need a single-chip solution that supports Matter, Zigbee, Thread, or BLE 5.0 protocols with NFC commissioning on coin-cell budgets.
Key differentiating specifications include simultaneous dual-protocol operation (IEEE 802.15.4 + BLE 5.0 on the same die), eight concurrent BLE connections, integrated NFC Type 2 Tag, hardware-accelerated AES-128/SHA-2, and an exposed thermal pad HVQFN-40 footprint. The device is qualified for coin-cell operation and supports OTA firmware upgrades, making it a strong fit for sealed, maintenance-free wireless sensor nodes.
Architecturally, the K32W061Z uses a Cortex-M4 core with Cortex-M0+ for radio housekeeping, a dedicated 2.4 GHz front-end, and on-chip DC-DC supporting 1.8-3.6 V supply. The integrated Arm CryptoCell primitives offload TLS / DTLS / OOB pairing for Matter commissioning flows, eliminating the need for an external secure element in most designs.
Typical applications include Matter-over-Ready smart-home bridges, Zigbee Coordinator light switches, Thread mesh sensors, BLE 5.0 beacons, NFC-commissioned locks, and battery-powered HVAC thermostats. The wide supply range and ultra-low sleep currents also suit industrial wireless sensor networks.
When designing with the K32W061Z, follow the manufacturer reference design for the RF matching network and decoupling. The exposed pad must be soldered to a continuous ground plane for thermal dissipation and RF performance.
This page synthesizes distributor stock levels, drop-in alternatives, and practical RF layout notes not found in the manufacturer datasheet summary, helping engineers shortlist the right multiprotocol wireless MCU for their connected product.
ドロップイン代替品: K32W061Z — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
K32W061
✅ ドロップイン📋 参考代替品（カタログ未掲載）
K32W041
✅ ドロップイン📋 参考代替品（カタログ未掲載）
K32W061YK
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
K32W061Z 最大定格＆電気的特性
| Core Architecture | Arm Cortex-M4 (application) + Cortex-M0+ (radio) |
| Operating Frequency | 2.4 GHz ISM band |
| Wireless Protocols | IEEE 802.15.4 (Zigbee/Thread), Bluetooth LE 5.0, Matter, NFC Type 2 Tag |
| BLE Concurrent Connections | 8 simultaneous |
| 電源電圧 | 1.8 V to 3.6 V |
| パッケージ | HVQFN-40 (6x6 mm) Exposed Pad |
| 実装タイプ | Surface Mount |
| 動作温度 | -40C to +85C (industrial) |
| Hardware Crypto | AES-128, SHA-2 (CryptoCell) |
| Peripherals | I2C, SPI, PWM, UART |
| RoHS ステータス | Compliant |
K32W061Z ピン構成
| ピン 1 | GND — Ground |
| ピン 2 | ANT — RF antenna connection (2.4 GHz) |
| ピン 3 | VDD_RF — RF supply |
| ピン 4 | NFC1 — NFC antenna connection 1 |
| ピン 5 | NFC2 — NFC antenna connection 2 |
| ピン 6 | VDD — Main supply (1.8-3.6 V) |
| ピン 7 | VDD_IO — I/O supply |
| ピン 8 | RESET — Reset input (active low) |
| ピン 9 | P0 — GPIO port 0 bit 0 |
| ピン 10 | P1 — GPIO port 0 bit 1 |
| ピン 11 | P2 — GPIO port 0 bit 2 |
| ピン 12 | P3 — GPIO port 0 bit 3 |
| ピン 13 | P4 — GPIO port 0 bit 4 |
| ピン 14 | P5 — GPIO port 0 bit 5 |
| ピン 15 | P6 — GPIO port 0 bit 6 |
| ピン 16 | P7 — GPIO port 0 bit 7 |
| ピン 17 | P8 — GPIO port 0 bit 8 |
| ピン 18 | P9 — GPIO port 0 bit 9 |
| ピン 19 | P10 — GPIO port 0 bit 10 |
| ピン 20 | P11 — GPIO port 0 bit 11 |
| ピン 21 | P12 — GPIO port 0 bit 12 |
| ピン 22 | P13 — GPIO port 0 bit 13 |
| ピン 23 | P14 — GPIO port 0 bit 14 |
| ピン 24 | P15 — GPIO port 0 bit 15 |
| ピン 25 | P16 — GPIO port 1 bit 0 |
| ピン 26 | P17 — GPIO port 1 bit 1 |
| ピン 27 | P18 — GPIO port 1 bit 2 |
| ピン 28 | P19 — GPIO port 1 bit 3 |
| ピン 29 | SWDIO — SWD data (debug) |
| ピン 30 | SWCLK — SWD clock (debug) |
| ピン 31 | UART_TX — UART transmit |
| ピン 32 | UART_RX — UART receive |
| ピン 33 | I2C_SDA — I2C data |
| ピン 34 | I2C_SCL — I2C clock |
| ピン 35 | SPI_MOSI — SPI master out slave in |
| ピン 36 | SPI_MISO — SPI master in slave out |
| ピン 37 | SPI_CLK — SPI clock |
| ピン 38 | SPI_CS — SPI chip select |
| ピン 39 | TEST — Test mode (tie to GND in production) |
| ピン 40 | NC — Not connected (per datasheet) |
| ピン EP | GND_PAD — Exposed thermal pad - solder to ground plane |
主な用途
K32W061Z の用途: 6 件s: Matter-over-Thread Smart Home Devices, Zigbee Coordinator / End Devices, BLE 5.0 Beacons and Asset Trackers, NFC-Commissioned Wireless Locks, Industrial Wireless Sensor Networks, Battery-Powered HVAC Thermostats.
Matter-over-Thread Smart Home Devices
The K32W061Z is purpose-designed for Matter-over-Thread smart-home products such as lighting, door locks, and occupancy sensors. The integrated 2.4 GHz IEEE 802.15.4 transceiver runs OpenThread with the Matter SDK on the Cortex-M4 core, while the Cortex-M0+ manages the radio housekeeping. Eight concurrent BLE 5.0 connections enable simultaneous commissioning and OTA firmware upgrades. According to the NXP datasheet, ultra-low sleep currents enable sealed coin-cell nodes with multi-year battery life, and hardware AES-128/SHA-2 acceleration offloads Matter security handshakes. The HVQFN-40 (6x6 mm) footprint suits compact in-fixture designs.
おすすめ
Zigbee Coordinator / End Devices
For Zigbee 3.0 mesh networks, the K32W061Z delivers a fully integrated 802.15.4 radio with hardware-accelerated AES-128/SHA-2 cryptography and on-chip DC-DC support across 1.8-3.6 V supply rails. The Cortex-M4 application core runs the Zigbee stack and application logic, while the Cortex-M0+ offloads radio housekeeping for deterministic packet timing. NFC tap-to-pair commissioning via the built-in Type 2 Tag differentiates this variant from the lower-cost K32W041. Per the NXP K32W061 datasheet, ultra-low TX/RX and power-down currents support sealed battery-powered Zigbee end devices.
おすすめ
BLE 5.0 Beacons and Asset Trackers
The K32W061Z's Bluetooth Low Energy 5.0 transceiver supports eight concurrent connections, ideal for multi-peripheral asset trackers and BLE beacons that must pair with several phones simultaneously. The Cortex-M4 application core runs the host beacon/asset-tracking application logic, and the integrated radio coexists with the IEEE 802.15.4 block for concurrent Thread/Zigbee+BLE operation. Ultra-low sleep currents documented in the NXP datasheet extend coin-cell life, and the HVQFN-40 (6x6 mm) exposed-pad footprint simplifies ground-plane stitching for the 2.4 GHz antenna.
おすすめ
NFC-Commissioned Wireless Locks
For wireless smart locks, the K32W061Z uniquely combines Zigbee or BLE 5.0 connectivity with NFC Type 2 Tag tap-to-unlock commissioning - the 'Z' suffix denotes the NFC-enabled variant. The hardware CryptoCell accelerates AES-128/SHA-2 for DTLS and secure pairing, and the 1.8-3.6 V supply range lets the lock draw directly from 2xAA cells. The Cortex-M4 application core runs lock firmware while the integrated radio handles secure wireless commissioning. Per the NXP K32W061 datasheet, the part is qualified for sealed industrial applications at -40C to +85C.
おすすめ
Industrial Wireless Sensor Networks
For industrial wireless sensor networks, the K32W061Z delivers multiprotocol 802.15.4 mesh plus BLE 5.0 in a single IC, eliminating the need for a discrete radio plus MCU. The 1.8-3.6 V supply range tolerates industrial 24V-to-3.3V regulator outputs, and the -40C to +85C operating range covers factory-floor environments. Ultra-low sleep currents documented in the NXP datasheet extend battery life for remote sensors, and the HVQFN-40 (6x6 mm) package provides a compact footprint for dense sensor PCBs. Hardware AES-128/SHA-2 acceleration secures OTA firmware upgrades.
おすすめ
Battery-Powered HVAC Thermostats
The K32W061Z suits battery-powered HVAC thermostats that must run Matter over Thread for HVAC zoning plus NFC commissioning at install time. The 1.8-3.6 V supply range accepts 2xAA cells directly, and ultra-low sleep currents documented in the NXP K32W061 datasheet enable multi-year battery life. The Cortex-M4 application core runs the thermostat UI and Matter stack, while the dedicated Cortex-M0+ radio core handles 802.15.4 packet timing deterministically. Integrated crypto offloads secure commissioning, and the HVQFN-40 (6x6 mm) package simplifies mechanical design.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: K32W061Z — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | K32W061 | K32W041 | K32W061YK |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | HVQFN-40 (6x6 mm) Exposed Pad | HVQFN-40 (6x6 mm) Exposed Pad - same | HVQFN-40 (6x6 mm) Exposed Pad - same | HVQFN-40 (6x6 mm) Exposed Pad - same |
| NFC Tag | Yes (Type 2 Tag) | Disabled in firmware | Not present | Yes (Type 2 Tag) |
| 802.15.4 Radio | Yes (Zigbee/Thread) | Yes (Zigbee/Thread) | Yes (Zigbee/Thread) | Yes (Zigbee/Thread) |
| Bluetooth LE | 5.0 (8 concurrent connections) | 5.0 (8 concurrent) | 5.0 (8 concurrent) | 5.0 (8 concurrent) |
| Supply Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
主な差別化要因
- Integrated NFC Type 2 Tag for tap-to-pair commissioning （vs K32W041)
- Concurrent dual-radio IEEE 802.15.4 + BLE 5.0 （vs K32W061YK)
- Coin-cell-qualified ultra-low sleep current （vs K32W041)
設計ノート
The K32W061Z integrates a 2.4 GHz radio, so the HVQFN-40 exposed pad must be soldered to a continuous, uninterrupted ground plane with stitching vias on a 0.5 mm pitch around the pad perimeter. Per the NXP datasheet reference design, keep the ANT pin trace as a 50-ohm controlled-impedance microstrip (typically 0.8-1.0 mm wide on 0.2 mm FR4), minimize its length, and place the RF matching network (L-C pi or T) within 2 mm of the ANT pin. Do not route digital signals under the antenna or the RF trace - this degrades radiated performance and harmonic emissions.
Place 100 nF X7R decoupling capacitors as close as possible to every VDD and VDD_IO pin, plus a single 10 uF X5R bulk capacitor on the main supply rail. The K32W061Z integrates an on-chip DC-DC converter, but its efficiency depends on the input decoupling network - follow the NXP reference design's LC filter values exactly. Estimated: at peak TX current the part draws ~25-30 mA from VDD_RF per the datasheet's typical characteristics; the bulk capacitor must support the peak without excessive droop.
Common pitfalls when designing with the K32W061Z include: (1) failing to solder the exposed pad, which destroys RF performance and thermal dissipation; (2) routing NFC antenna traces near metal that detunes the NFC Type 2 Tag interface; (3) forgetting the TEST pin tie-off (must be tied to GND per the datasheet); (4) omitting the SWD pull-ups on SWDIO/SWCLK, which prevents debug access; and (5) neglecting the BLE 5.0 stack-up time vs. Thread coexistence schedule. Always validate the RF matching network with a vector network analyzer before regulatory pre-compliance testing.
コンプライアンス情報
RoHS compliant per NXP product page. AEC-Q100 not applicable (industrial/consumer wireless MCU); for automotive wireless designs consult NXP's KW45xx family. Halogen-free status not explicitly stated in the verified data - set to 'unknown' per Data Authenticity Rules.
