LM258WYPT - Dual 30V Low-Power Op Amp | STMicroelectronics
部品番号: LM258WYPT ✓ 生産中LM258WYPT 概要
A low-power dual operational amplifier is an analog signal-conditioning IC that provides voltage gain while remaining usable from a single positive supply. In the product hierarchy, the LM258 belongs to operational amplifiers, analog amplifiers, analog signal-processing ICs, and broader semiconductor components. Its internally compensated architecture simplifies design because each amplifier does not require an external compensation network for ordinary closed-loop operation.
The LM258WYPT emphasizes low supply current, approximately 700 µA, with a supply drain that remains largely independent of supply magnitude. Its 20 nA input bias current suits many high-impedance sensing paths, while the 1.1 MHz gain-bandwidth product supports general-purpose signal conditioning at low frequencies. The two amplifiers are independent, allowing simultaneous channel processing or use in unrelated circuit blocks.
Internally frequency compensation stabilizes operation in common feedback configurations. The 600 V/µs slew rate provides useful response for audio, transducer, and industrial control signals, although the device is not optimized for high-speed precision applications. The 85 dB open-loop gain and 2 mV offset specification define its practical precision in feedback-based amplifier stages.
Typical uses include low-frequency sensor amplification, audio preamplification, bridge-amplifier signal conditioning, current-loop interfaces, and general industrial control. The 30 V supply capability also permits operation from higher-voltage rails when the signal amplitude remains within the amplifier's input and output limits. Independent amplifiers make the device useful in dual-channel transducers and compact analog front ends.
Designers should verify common-mode and output-swing limits against the selected supply voltage, provide suitable bypassing near the power pins, and account for input bias current when working with high-source-impedance sensors. Stable feedback layout, short output paths, and clean grounding remain important because PCB leakage and leakage current can disturb sensitive measurements even when the amplifier itself performs correctly.
This page combines package, electrical, application, sourcing, and replacement information into an engineering-focused guide. It also distinguishes the exact LM258WYPT order code from related LM258 variants whose temperature grade, offset bin, package, or tape-and-reel suffix can differ.
ドロップイン代替品: LM258WYPT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
LM258AWYPT
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LM258WYPT 最大定格&電気的特性
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Circuits | 2 circuits |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1.1 MHz |
| Slew Rate | 0.6 V/µs |
| Open-Loop Gain | 85 dB |
| Input Offset Voltage | 2 mV |
| Input Bias Current | 20 nA |
| 電源電流 | 700 µA |
| Output Current | 40 mA |
| Frequency Compensation | Internal |
| Supply Type | Single or split supply |
| パッケージ | TSSOP-8 |
| 実装タイプ | Surface mount |
| Packaging Form | Tape and reel |
| RoHS ステータス | Compliant |
LM258WYPT tssop-8 ピン配置ガイド
LM258WYPT (tssop-8 パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: LM258WYPT.
詳細は データシート をご参照ください。
主な用途
LM258WYPT の用途: 6 件s: Low-Frequency Transducer Buffering, Audio Preamplification, Current-to-Voltage Signal Conversion, Industrial Bridge-Sensor Amplification, Power-Supply Feedback and Monitoring, Temperature and Pressure Sensor Interfaces.
Low-Frequency Transducer Buffering
The LM258WYPT suits low-frequency sensor buffers because its two independent channels can condition two measurement inputs while drawing approximately 700 µA of supply current. The 20 nA input bias current reduces loading from high-impedance sources, and the 85 dB open-loop gain supports practical closed-loop gain stages. Each internally compensated amplifier simplifies implementation around resistive feedback networks. The principal design constraint is the input common-mode range: sensor output voltage must remain inside the amplifier’s valid range for the selected supply. A 30 V maximum supply rating provides flexibility for industrial systems, although protection, guarding, and leakage control remain necessary around high-impedance transducers.
おすすめ
Audio Preamplification
The LM258WYPT can provide two channels of general-purpose audio preamplification when compactness and low supply current are priorities. Its 1.1 MHz gain-bandwidth product covers the audible range with additional bandwidth margin, while the 0.6 V/µs slew rate handles moderate signal excursions. The dual, independent architecture supports stereo or dual-mono signal conditioning without sharing an input or output. Designers should keep the signal within the output-swing limits, use stable feedback ratios, and bypass the supply pins locally. The 2 mV input offset is generally acceptable for audio, but it is not appropriate when a precision reference or instrumentation-amplifier error budget requires sub-millivolt accuracy.
おすすめ
Current-to-Voltage Signal Conversion
A feedback transimpedance stage can use one LM258WYPT channel for sensor-current conversion and the second channel for gain or filtering. The approximately 20 nA input bias current is favorable for moderate source impedances, and the 85 dB open-loop gain helps preserve loop gain in a feedback configuration. With a 1.1 MHz gain-bandwidth product, the amplifier supports bandwidths appropriate for many slow sensor and industrial-control signals. Practical performance depends on feedback-resistor selection, input capacitance, board leakage, and output-swing margin. Check the resulting noise gain and stability across the required signal range rather than assuming the amplifier’s nominal bandwidth alone determines the usable response.
おすすめ
Industrial Bridge-Sensor Amplification
The LM258WYPT’s two independent amplifiers are convenient for differential bridge-sensor front ends when one channel handles excitation-side buffering or filtering and the other processes the bridge output. Its 30 V maximum supply rating supports higher-voltage industrial control rails, while approximately 700 µA supply current keeps the amplifier suitable for distributed, low-power instrumentation. The 2 mV offset and 20 nA bias current must be included in the system error budget, particularly for resistive bridges with high source impedance. PCB routing should preserve signal symmetry, maintain clean grounding, and minimize leakage between high-impedance input nodes and nearby supply or digital traces.
おすすめ
Power-Supply Feedback and Monitoring
The LM258WYPT can monitor a regulated rail and amplify the difference between a feedback voltage and a reference, making its two channels useful for supervisory or fault-detection functions. The wide 30 V supply capability permits operation around higher-voltage industrial rails, provided the input common-mode and output-swing requirements are respected. Its 700 µA supply consumption is useful when every milliampere affects standby power. Because this is a general-purpose amplifier rather than a dedicated supervisor, threshold accuracy, fault-response time, and reference quality depend on the external network. Keep feedback traces short, isolate the amplifier from noisy switching nodes, and ensure stable operation under transient loading.
おすすめ
Temperature and Pressure Sensor Interfaces
The LM258WYPT is appropriate for slow temperature and pressure sensors whose outputs fall within the common-mode range of the selected supply. Two independent channels can handle complementary sensor signals or provide buffering for a resistance-based bridge. The amplifier’s 20 nA input bias current reduces error with moderately high sensor impedances, while its 1.1 MHz bandwidth is more than adequate for many thermal and mechanical measurement systems. Offset error, drift, sensor excitation noise, and resistor tolerances will usually dominate the overall accuracy. Use guarded input layouts, clean reference connections, and local supply bypassing to obtain repeatable low-level measurements.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM258WYPT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM258AWYPT |
|---|---|---|
| Package | TSSOP-8 | TSSOP-8 |
| Brand | STMicroelectronics | STMicroelectronics |
| Amplifier Configuration | Dual | Dual |
| Maximum Supply Voltage | 30 V | 30 V |
| Gain-Bandwidth Product | 1.1 MHz | 1.1 MHz |
| Slew Rate | 0.6 V/µs | 0.6 V/µs |
| Input Offset Voltage | 2 mV | Tighter offset bin |
| Input Bias Current | 20 nA | 20 nA |
| Supply Current | 700 µA | 700 µA |
| Open-Loop Gain | 85 dB | 85 dB |
| Output Current | 40 mA | 40 mA |
| Internal Frequency Compensation | Yes | Yes |
主な差別化要因
- Retains the standard LM258 performance envelope (vs LM258AWYPT)
- Uses the standard offset-voltage bin (vs LM258AWYPT)
- Combines two independent low-power channels (vs LM258AWYPT)
設計ノート
Place the input, output, and feedback components close to the LM258WYPT pins, particularly the power terminals. Keep each amplifier’s feedback loop compact and route high-impedance input nodes away from switching nodes and noisy digital traces. Because the amplifier can be used with two independent channels, preserve channel separation in the layout and provide a common, low-impedance ground reference. Use the manufacturer pin-description table when defining land patterns and keepout requirements.
Confirm input common-mode voltage and output-swing limits for the actual supply voltage before finalizing the feedback network. A nominal 30 V maximum supply rating does not imply that the amplifier can process signals across the entire input range on every supply. Add local bypass capacitance at the supply pins and route it through a short, low-inductance path. For battery-powered circuits, include the approximately 700 µA device current as well as load and divider currents in the standby-power budget.
Use the 1.1 MHz gain-bandwidth product and 0.6 V/µs slew rate as design limits rather than guaranteed final-stage bandwidth. Check the required signal frequency, closed-loop noise gain, output loading, and resulting stability margin. High-impedance sensor nodes should be guarded against PCB contamination and leakage. If the application includes a large feedback resistor, verify bias-current error, input capacitance, and settling behavior across the intended signal range.
コンプライアンス情報
RoHS compliance is identified in the product listing. Other compliance attributes require confirmation from the manufacturer’s order-code or quality documentation.