LM2902N/NOPB - Quad 26V 1MHz Op Amp | Texas Instruments
部品番号: LM2902N/NOPB ✓ 生産中LM2902N/NOPB 概要
An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain and negative feedback to amplify voltage differences. The quad-amplifier configuration places four independent operational amplifiers in one package, reducing component count and board area where multiple analog channels are required. Within the power-management hierarchy, an LM2902N/NOPB belongs to the linear integrated-circuit family, while functionally it serves as an analog signal-processing IC for instrumentation, control, and interface circuits.
Key characteristics include four independent channels, a 26 V maximum supply rating, 1 MHz gain-bandwidth performance, and approximately 0.5 V/µs slew rate. The internally compensated architecture avoids external frequency-compensation components in ordinary closed-loop applications. Input and output arrangements follow the conventional dual-inline operational-amplifier pinout, allowing each channel to be used independently as long as the unused amplifier is configured safely.
The wide single-supply operating range allows the device to operate from industrial and automotive-related 12 V rails, provided the supply remains within the 26 V rating. Its 1 MHz bandwidth is appropriate for low-frequency control loops, transducers, analog interfaces, and general-purpose signal conditioning rather than high-speed video or communications channels. The PDIP package also supports through-hole assembly and hand prototyping.
Typical applications include four-channel sensor amplification, industrial process-control loops, bridge-signal conditioning, audio preamplification, active filtering, and general analog computation. Each channel can also serve as a comparator when configured with suitable positive feedback, although the output-stage behavior and saturation recovery should be evaluated for the target circuit.
When laying out a board, place the device away from switching nodes and high-current return paths, provide a local supply bypass capacitor close to the power pin, and route high-impedance input traces away from output and clock signals. Check input and output common-mode limits, output-current demand, thermal dissipation, and supply stability against the manufacturer datasheet before releasing the design.
This product page combines the exact orderable part information with practical package, application, replacement, and circuit-layout guidance. It also distinguishes the 14-pin PDIP target from surface-mount family members so engineers can avoid selecting a mechanically incompatible substitute.
ドロップイン代替品: LM2902N/NOPB — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM2902N/NOPB (同一形状・フットプリント) — 相違点: Package Type.
LM2902N
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902N/PB
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902N
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902N
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902N
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902N/NOPB 最大定格&電気的特性
| Product Type | Quad general-purpose operational amplifier |
| Number of Amplifier Channels | 4 channels |
| Supply Voltage Range | 3 V to 26 V |
| Maximum Supply Voltage | 26 V |
| Unity-Gain Bandwidth | 1 MHz |
| Slew Rate | 0.5 V/µs |
| Compensation | Internally frequency compensated |
| 動作温度範囲 | -40 °C to 85 °C |
| Package Type | 14-pin PDIP |
| ピン数 | 14 pins |
| 実装スタイル | Through-hole |
| 出力タイプ | Push-pull |
LM2902N/NOPB ピン構成
| ピン 1 | OUT1 — Amplifier 1 output |
| ピン 2 | IN1- — Amplifier 1 inverting input |
| ピン 3 | IN1+ — Amplifier 1 non-inverting input |
| ピン 4 | V+ — Positive supply voltage |
| ピン 5 | IN2+ — Amplifier 2 non-inverting input |
| ピン 6 | IN2- — Amplifier 2 inverting input |
| ピン 7 | OUT2 — Amplifier 2 output |
| ピン 8 | OUT3 — Amplifier 3 output |
| ピン 9 | IN3- — Amplifier 3 inverting input |
| ピン 10 | IN3+ — Amplifier 3 non-inverting input |
| ピン 11 | V- — Negative supply voltage |
| ピン 12 | IN4+ — Amplifier 4 non-inverting input |
| ピン 13 | IN4- — Amplifier 4 inverting input |
| ピン 14 | OUT4 — Amplifier 4 output |
主な用途
LM2902N/NOPB の用途: 6 件s: Industrial Sensor Signal Conditioning, Wheatstone Bridge Instrumentation, Active Audio Preamplification, Automotive Control Interfaces, 12V and 24V Control Loops, General Comparator and Threshold Circuit.
Industrial Sensor Signal Conditioning
The LM2902N/NOPB is well suited to conditioning low-frequency sensor signals because four independent, internally compensated amplifiers can handle multiple inputs without requiring separate packages. A typical use places one amplifier in a non-inverting configuration, another in an active filter, and the remaining channels in gain or offset stages. The 3 V to 26 V single-supply range supports industrial rails, while the 1 MHz unity-gain bandwidth provides ample margin for temperature, pressure, and position sensors with relatively slow signals. Designers should still confirm the input common-mode range and output swing against the sensor excitation voltage before finalizing the circuit.
おすすめ
Wheatstone Bridge Instrumentation
The LM2902N/NOPB can form the input and output stages of a bridge-measurement circuit, where small differential sensor voltages must be amplified accurately. Its four independent channels allow a bridge amplifier, gain stage, filter, and output buffer to share one 14-pin PDIP package. The 1 MHz unity-gain bandwidth is much higher than required by many resistive temperature, strain, and pressure elements, helping preserve bandwidth for filtering and response time. The real limitation is input offset and common-mode behavior, which must be checked for the bridge excitation and sensor-ground arrangement used in the final instrumentation design.
おすすめ
Active Audio Preamplification
The LM2902N/NOPB can implement low-frequency audio preamplifier and active-filter stages using its four independent amplifiers. A useful arrangement assigns separate channels to input gain, frequency shaping, output buffering, and a second audio path, reducing the number of packages on a mixer or line-level board. Its 1 MHz bandwidth is substantially above the 20 kHz audio band, while the approximately 0.5 V/µs slew rate supports clean handling of moderate signal amplitudes. The through-hole PDIP format is particularly convenient for prototypes and educational equipment, although output-current capability and output swing should be checked against headphone or line-driver loads.
おすすめ
Automotive Control Interfaces
The LM2902N/NOPB can support low-frequency control and interface circuits in automotive equipment because it combines four independent channels with a 26 V maximum supply rating and an operating range of -40 °C to 85 °C. The device is suited to actuator feedback, switch-condition conditioning, and general analog control blocks when the system remains below its electrical limits. The quad arrangement reduces board area compared with four single amplifiers. Automotive qualification status and exact transient requirements should be confirmed for the chosen ordering code, while PCB layout should keep this through-hole device away from high-current switching paths and severe temperature gradients.
おすすめ
12V and 24V Control Loops
The LM2902N/NOPB is a practical choice for error amplifiers and servo loops running from nominal 12 V or 24 V industrial supplies, as long as transient voltage remains within the 26 V maximum. Its internally compensated amplifiers simplify implementation of proportional-integral control loops, and four channels allow one controller plus three auxiliary analog functions on the same board. The 1 MHz bandwidth allows proportional loops far beyond ordinary process-control dynamics. Designers should add supply filtering and reverse-polarity protection at the board level, account for op-amp input offset, and verify common-mode behavior around the sensor and actuator voltage range.
おすすめ
General Comparator and Threshold Circuit
Each LM2902N/NOPB amplifier can operate as a comparator when its feedback path introduces positive feedback, allowing four independent threshold channels in one package. Such circuits can monitor supply rails, sensor outputs, or resistor-divider crossings and drive logic or relay-control stages. The 3 V to 26 V operating range is useful for higher-voltage industrial thresholds, while the four-channel arrangement reduces component count. Because the same amplifier is not a dedicated open-collector comparator, the design must account for push-pull output behavior, input offset, output saturation, and propagation delay rather than assuming ideal comparator behavior.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM2902N/NOPB — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM2902N | LM2902N/PB | LM2902N | LM2902N | LM2902N |
|---|---|---|---|---|---|---|
| Package | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics | onsemi | NXP Semiconductors |
| Amplifier Count | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
主な差別化要因
- Four independent general-purpose amplifiers in one through-hole package (vs LM324AN/PB)
- Same 14-pin PDIP footprint as the principal second-source LM2902N (vs STMicroelectronics LM2902N)
- Standard TI order code with a 1 MHz bandwidth (vs LM2902N/PB)
- Operation extends from -40 °C to 85 °C (vs LM324AN/PB)
設計ノート
Place a high-frequency bypass capacitor and a bulk capacitor close to the supply pins, with the short return path connected directly to the ground pin. Although the LM2902N/NOPB is specified for single-supply operation from 3 V to 26 V, board transients can exceed the nominal rail. Validate the maximum supply tolerance, startup behavior, and output load current against the manufacturer electrical-characteristics table before selecting capacitor voltage ratings.
Route the four non-inverting inputs and four inverting inputs as short, quiet traces away from supply switching nodes, relay contacts, and the amplifier outputs. The PDIP footprint makes prototype wiring straightforward, but long breadboard or flying-lead connections can increase oscillation risk. Keep feedback components close to their associated amplifier pins, use a solid ground reference, and avoid placing long output routes adjacent to high-impedance sensor inputs.
Do not treat the 26 V maximum supply rating as permission to exceed the input common-mode range. Check that signals remain within the permitted input range and that output swing supports the required load at the selected supply voltage. If an amplifier is used as a comparator, configure positive feedback and account for push-pull output saturation. Unused amplifier channels should be tied to a defined potential rather than left floating.
For circuits adjacent to motors, relays, or switching regulators, reserve filtering for each affected analog channel rather than relying only on one common supply filter. Add series resistance at connector inputs when source impedance permits, clamp exposed inputs against ESD events, and keep the supply return path away from high-current switching currents. The quad package reduces board area, but four active channels can increase the importance of separating their return currents and ground references.
コンプライアンス情報
The /NOPB order suffix identifies a no-PB ordering option, but RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals status were not stated in the cited product listings and require confirmation from the manufacturer.