LM2902PWR - Quad 36V 1.2MHz Op Amp | Texas Instruments
部品番号: LM2902PWR ✓ 生産中LM2902PWR 概要
An operational amplifier is an analog signal-processing IC that uses differential feedback to amplify the difference between its inverting and non-inverting inputs. The LM2902 belongs to the hierarchy of operational amplifier, analog amplifier, analog signal IC, and semiconductor. Four independent channels in one package simplify designs requiring several amplifiers, while reducing the number of PCB components compared with four single-amplifier packages.
The LM2902 provides four independent, internally compensated amplifiers with a common-mode input range that can extend to ground. This is useful in battery-powered and single-supply circuits where signals may remain near the lower supply rail. Its 1.2 MHz gain-bandwidth product supports general-purpose signal conditioning, including audio-frequency amplification, buffering, comparison functions, active filters, and sensor-interface stages.
The wide supply capability distinguishes the LM2902 from low-voltage rail-to-rail amplifiers commonly used in compact battery-powered electronics. A nominal 26 V operating range and operation up to 36 V allow the same device family to address industrial control, instrumentation, and power-supply support circuits where higher-voltage signals and supplies may be present. The device is not intended to replace precision or rail-to-rail input amplifiers when sub-millivolt accuracy is required.
Typical uses include four-channel audio preamplification, low-frequency active filters, transducer conditioning, current-loop interfaces, and general instrumentation. Because each amplifier is independent, the four channels can also perform different functions on one board. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer’s recommended stable-input arrangement.
For a 14-TSSOP implementation, verify the complete pin map and thermal pad treatment against the manufacturer datasheet before layout release. The principal design trade-off is the combination of high-voltage tolerance and unity-gain stability versus the lower bandwidth, higher offset, and lack of rail-to-rail operation associated with this classic general-purpose amplifier architecture.
This page combines the key operating characteristics, package information, sourcing guidance, drop-in alternatives, and practical circuit considerations needed to evaluate the LM2902PWR in industrial, instrumentation, audio, and embedded analog designs.
ドロップイン代替品: LM2902PWR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM2902PWR (同一形状・フットプリント) — 相違点: Package, Gain-Bandwidth Product, Product Type, Input Offset Voltage, Maximum Supply Voltage.
LM2902PWRG4
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902PWRG3
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902KPWR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902PWR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902PWR 最大定格&電気的特性
| Amplifier Count | 4 circuits |
| Product Type | General-purpose operational amplifier |
| Nominal Supply Voltage | 26 V |
| Maximum Supply Voltage | 36 V |
| Supply Voltage Range | 3 V to 36 V for B and BA versions |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV maximum at 25°C for BA versions, LM2902A, and LM124A |
| Common-Mode Input Range | Extends to ground |
| Differential Input Voltage Capability | High differential input voltage capability |
| Internal Compensation | Frequency compensated |
| Package Type | 14-TSSOP |
| 実装タイプ | Surface mount |
| Channel Independence | 4 independent amplifiers |
LM2902PWR ピン構成
| ピン 1 | OUT1 — Amplifier 1 output |
| ピン 2 | IN1- — Amplifier 1 inverting input |
| ピン 3 | IN1+ — Amplifier 1 non-inverting input |
| ピン 4 | V+ — Positive supply connection |
| ピン 5 | IN2+ — Amplifier 2 non-inverting input |
| ピン 6 | IN2- — Amplifier 2 inverting input |
| ピン 7 | OUT2 — Amplifier 2 output |
| ピン 8 | OUT3 — Amplifier 3 output |
| ピン 9 | IN3- — Amplifier 3 inverting input |
| ピン 10 | IN3+ — Amplifier 3 non-inverting input |
| ピン 11 | V- — Negative supply connection |
| ピン 12 | IN4+ — Amplifier 4 non-inverting input |
| ピン 13 | IN4- — Amplifier 4 inverting input |
| ピン 14 | OUT4 — Amplifier 4 output |
主な用途
LM2902PWR の用途: 6 件s: Industrial Sensor Signal Conditioning, Audio Preamplification, Active Low-Frequency Filters, Power-Supply Monitoring and Control, Current-Loop Transmitter Interface, Test and Measurement Buffering.
Industrial Sensor Signal Conditioning
The LM2902PWR fits industrial sensor conditioning because its common-mode input range extends to ground, allowing signals near the lower supply rail to be amplified in single-supply systems. Four independent channels can support bridge, temperature, pressure, or current-sensor stages while sharing one 14-TSSOP footprint. Its 1.2 MHz gain-bandwidth product is adequate for low-bandwidth process signals, and the 26 V nominal supply range is useful for industrial interfaces. The design must still verify sensor output swing, input bias current, output swing, and channel-to-channel gain error before selecting resistor values.
おすすめ
Audio Preamplification
The LM2902PWR can implement four low-frequency preamplifier channels in audio equipment because each internal amplifier is independent and frequency compensated. Its 1.2 MHz gain-bandwidth product covers the common audio-band use case, while the common-mode input range extending to ground simplifies biasing around a single positive supply. The four-channel package reduces board area compared with four separate single amplifiers. For microphone or line-level inputs, confirm input bias current, noise performance, output headroom, and channel matching; the device is better suited to general audio conditioning than low-noise premium preamplification.
おすすめ
Active Low-Frequency Filters
The LM2902PWR is appropriate for active filters requiring several amplifier stages because it combines four independent channels with a 1.2 MHz gain-bandwidth product. Typical uses include low-pass, high-pass, and band-pass sections in control, measurement, and audio equipment. The internally compensated amplifiers simplify unity-gain filter design, and the common-mode input range extending to ground assists single-supply biasing. Component tolerances and amplifier gain-bandwidth behavior determine the achievable filter response, so verify the exact frequency response and output swing rather than relying only on nominal bandwidth.
おすすめ
Power-Supply Monitoring and Control
The LM2902PWR can support threshold monitoring, error amplification, and feedback shaping in higher-voltage power-supply control circuits. Its 26 V nominal supply operation and common-mode input range extending to ground help when monitoring signals originate near the negative rail. Four independent channels allow separate comparisons or control loops to be consolidated into one package. Design checks should include input differential voltage, output saturation, supply current, and stability at the selected gain, especially when the circuit operates close to the maximum 36 V supply limit.
おすすめ
Current-Loop Transmitter Interface
The LM2902PWR can be used in current-loop instrumentation where several amplifier channels buffer sensor outputs and drive 4–20 mA interface circuits. The amplifier’s low-side common-mode capability is valuable in single-supply transmitter designs, and the 14-TSSOP package keeps four channels compact. Its 1.2 MHz bandwidth is more than adequate for typical process-control loop bandwidths. The implementation must account for output-current capability, load-drive behavior, loop compliance, input offset, and resistor accuracy because those parameters determine the final transmitter accuracy.
おすすめ
Test and Measurement Buffering
The LM2902PWR is useful for buffering and level-shifting in general-purpose test equipment where multiple instrument channels must share a compact analog front end. Four independent amplifiers can isolate sources, support gain stages, or generate comparison references. The 26 V nominal operating supply and common-mode input range reaching ground make the device useful for bench circuits powered from a single positive rail, while its 1.2 MHz bandwidth handles low-to-moderate frequency signals. Validate source loading, output swing, input bias current, and settling behavior for the intended measurement bandwidth.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM2902PWR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM2902PWRG4 | LM2902PW | LM2902KPWR | LM2902PWR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | ROHM Semiconductor |
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Amplifier Count | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Product Type | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | Standard general-purpose amplifier |
主な差別化要因
- Four independent high-voltage amplifiers in one compact package (vs LM2902PWRG4)
- Single-supply-friendly common-mode operation (vs LM2902PWR)
- Established 26 V nominal and 36 V maximum supply capability (vs LM2902PW)
設計ノート
Place a bypass capacitor close to the V+ pin and use the negative-supply connection as the reference point when the device operates from a single supply. The LM2902PWR is suited to higher-voltage circuits, but the selected capacitor voltage rating must tolerate the maximum rail voltage and any transient overshoot. Verify the exact recommended capacitor value and stability network in the manufacturer datasheet before finalizing the layout.
Route the four amplifier channels to minimize coupling between adjacent inputs and outputs, particularly when one channel handles a high-level signal and another handles a small sensor signal. Keep the TSSOP footprint within the manufacturer’s land-pattern and solder-mask recommendations, inspect the pin-1 orientation, and place the device close to the supply bypass capacitor. Differential input pairs should follow a compact, symmetrical route where practical.
Do not assume that every LM2902 variant is rail-to-rail or precision. The common-mode input range extends to ground, but output swing, input bias current, offset voltage, slew rate, and maximum differential input voltage remain important constraints. For unused channels, connect the inputs in a configuration that keeps the amplifier stable. Review the manufacturer’s recommended unused-circuit diagram rather than leaving an input floating.
The 1.2 MHz gain-bandwidth product is adequate for general low-frequency signal conditioning but limits closed-loop bandwidth and large-signal slew performance. Set the operating gain with the internal compensation characteristics in mind, keep feedback loops short, and verify settling at the signal bandwidth of interest. Add input protection when external sources can exceed the amplifier’s differential or common-mode limits.
コンプライアンス情報
The manufacturer and distributor pages identify the device and package, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is present in the cited product information.