Texas Instruments

LM2902PWR - Quad 36V 1.2MHz Op Amp | Texas Instruments

Teilenummer: LM2902PWR ✓ Aktiv
26 V Vdss 14-TSSOP Package
MOQ: 1 |

LM2902PWR Übersicht

Texas Instruments LM2902PWR is a quad general-purpose operational amplifier designed for single-supply or split-supply operation, with four high-voltage amplifiers in a 14-pin TSSOP package. Its headline characteristics include a 26 V nominal supply range, 1.2 MHz gain-bandwidth product, and approximately 2 mV input offset voltage.

An operational amplifier is an analog signal-processing IC that uses differential feedback to amplify the difference between its inverting and non-inverting inputs. The LM2902 belongs to the hierarchy of operational amplifier, analog amplifier, analog signal IC, and semiconductor. Four independent channels in one package simplify designs requiring several amplifiers, while reducing the number of PCB components compared with four single-amplifier packages.

The LM2902 provides four independent, internally compensated amplifiers with a common-mode input range that can extend to ground. This is useful in battery-powered and single-supply circuits where signals may remain near the lower supply rail. Its 1.2 MHz gain-bandwidth product supports general-purpose signal conditioning, including audio-frequency amplification, buffering, comparison functions, active filters, and sensor-interface stages.

The wide supply capability distinguishes the LM2902 from low-voltage rail-to-rail amplifiers commonly used in compact battery-powered electronics. A nominal 26 V operating range and operation up to 36 V allow the same device family to address industrial control, instrumentation, and power-supply support circuits where higher-voltage signals and supplies may be present. The device is not intended to replace precision or rail-to-rail input amplifiers when sub-millivolt accuracy is required.

Typical uses include four-channel audio preamplification, low-frequency active filters, transducer conditioning, current-loop interfaces, and general instrumentation. Because each amplifier is independent, the four channels can also perform different functions on one board. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer’s recommended stable-input arrangement.

For a 14-TSSOP implementation, verify the complete pin map and thermal pad treatment against the manufacturer datasheet before layout release. The principal design trade-off is the combination of high-voltage tolerance and unity-gain stability versus the lower bandwidth, higher offset, and lack of rail-to-rail operation associated with this classic general-purpose amplifier architecture.

This page combines the key operating characteristics, package information, sourcing guidance, drop-in alternatives, and practical circuit considerations needed to evaluate the LM2902PWR in industrial, instrumentation, audio, and embedded analog designs.

Drop-in-Alternativen für LM2902PWR – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit LM2902PWR (gleiche Bauform und Footprint) – abweichend in Package, Gain-Bandwidth Product, Product Type, Input Offset Voltage, Maximum Supply Voltage.

Texas Instruments
Package: 14-pin TSSOP
Gain-Bandwidth Product: 1 MHz
Vergleichen mit LM2902PWR →
Texas Instruments
Package: 14-pin TSSOP (PW), 4.40 mm width
Input Offset Voltage: 2 mV
Maximum Supply Voltage: 26 V
Vergleichen mit LM2902PWR →
Texas Instruments
Package: 14-TSSOP
Product Type: Quad general-purpose operational amplifier
Vergleichen mit LM2902PWR →

LM2902PWRG4

✅ Drop-In
Texas Instruments
📦 14-TSSOP
Quad general-purpose operational amplifier · 4 circuits · 26 V · 1.2 MHz · 14-TSSOP · Surface mount · Single supply or dual supply

Preis auf Anfrage

Datenblatt ansehen →

LM2902PWRG3

✅ Drop-In
Texas Instruments
📦 14-TSSOP
4 amplifiers · General-purpose · 26 V · 1.2 MHz · 2 mV · 0.5 V/µs · 0.8 mA typical · Single supply or split supply

Preis auf Anfrage

Datenblatt ansehen →

LM2902KPWR

✅ Drop-In
Texas Instruments
📦 14-TSSOP
4 amplifiers · General-purpose operational amplifier · 26 V · 1.2 MHz · 2 kV · -40 °C to +125 °C · Single-supply operation · Internally frequency compensated

Preis auf Anfrage

Datenblatt ansehen →

LM2902PWR

✅ Drop-In
Texas Instruments
📦 14-TSSOP
4 circuits · General-purpose operational amplifier · 26 V · 36 V · 3 V to 36 V for B and BA versions · 1.2 MHz · 2 mV maximum at 25°C for BA versions, LM2902A, and LM124A · Extends to ground

Preis auf Anfrage

Datenblatt ansehen →

LM2902PWR Grenzwerte & elektrische Eigenschaften

Amplifier Count 4 circuits
Product Type General-purpose operational amplifier
Nominal Supply Voltage 26 V
Maximum Supply Voltage 36 V
Supply Voltage Range 3 V to 36 V for B and BA versions
Gain-Bandwidth Product 1.2 MHz
Input Offset Voltage 2 mV maximum at 25°C for BA versions, LM2902A, and LM124A
Common-Mode Input Range Extends to ground
Differential Input Voltage Capability High differential input voltage capability
Internal Compensation Frequency compensated
Package Type 14-TSSOP
Montageart Surface mount
Channel Independence 4 independent amplifiers

LM2902PWR Pin-Konfiguration

TSSOP-14 (4.4mm) Package Pinout Diagram TSSOP-14 4.4x5mm, P0.65mm, JEDEC MO-153. 14-pin thin shrink. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 TSSOP-14 (4.4mm)
Pin 1 OUT1 — Amplifier 1 output
Pin 2 IN1- — Amplifier 1 inverting input
Pin 3 IN1+ — Amplifier 1 non-inverting input
Pin 4 V+ — Positive supply connection
Pin 5 IN2+ — Amplifier 2 non-inverting input
Pin 6 IN2- — Amplifier 2 inverting input
Pin 7 OUT2 — Amplifier 2 output
Pin 8 OUT3 — Amplifier 3 output
Pin 9 IN3- — Amplifier 3 inverting input
Pin 10 IN3+ — Amplifier 3 non-inverting input
Pin 11 V- — Negative supply connection
Pin 12 IN4+ — Amplifier 4 non-inverting input
Pin 13 IN4- — Amplifier 4 inverting input
Pin 14 OUT4 — Amplifier 4 output

Typische Anwendungen

LM2902PWR ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Audio Preamplification, Active Low-Frequency Filters, Power-Supply Monitoring and Control, Current-Loop Transmitter Interface, Test and Measurement Buffering.

🏭

Industrial Sensor Signal Conditioning

The LM2902PWR fits industrial sensor conditioning because its common-mode input range extends to ground, allowing signals near the lower supply rail to be amplified in single-supply systems. Four independent channels can support bridge, temperature, pressure, or current-sensor stages while sharing one 14-TSSOP footprint. Its 1.2 MHz gain-bandwidth product is adequate for low-bandwidth process signals, and the 26 V nominal supply range is useful for industrial interfaces. The design must still verify sensor output swing, input bias current, output swing, and channel-to-channel gain error before selecting resistor values.

🎧

Audio Preamplification

The LM2902PWR can implement four low-frequency preamplifier channels in audio equipment because each internal amplifier is independent and frequency compensated. Its 1.2 MHz gain-bandwidth product covers the common audio-band use case, while the common-mode input range extending to ground simplifies biasing around a single positive supply. The four-channel package reduces board area compared with four separate single amplifiers. For microphone or line-level inputs, confirm input bias current, noise performance, output headroom, and channel matching; the device is better suited to general audio conditioning than low-noise premium preamplification.

🔧

Active Low-Frequency Filters

The LM2902PWR is appropriate for active filters requiring several amplifier stages because it combines four independent channels with a 1.2 MHz gain-bandwidth product. Typical uses include low-pass, high-pass, and band-pass sections in control, measurement, and audio equipment. The internally compensated amplifiers simplify unity-gain filter design, and the common-mode input range extending to ground assists single-supply biasing. Component tolerances and amplifier gain-bandwidth behavior determine the achievable filter response, so verify the exact frequency response and output swing rather than relying only on nominal bandwidth.

⚡

Power-Supply Monitoring and Control

The LM2902PWR can support threshold monitoring, error amplification, and feedback shaping in higher-voltage power-supply control circuits. Its 26 V nominal supply operation and common-mode input range extending to ground help when monitoring signals originate near the negative rail. Four independent channels allow separate comparisons or control loops to be consolidated into one package. Design checks should include input differential voltage, output saturation, supply current, and stability at the selected gain, especially when the circuit operates close to the maximum 36 V supply limit.

📡

Current-Loop Transmitter Interface

The LM2902PWR can be used in current-loop instrumentation where several amplifier channels buffer sensor outputs and drive 4–20 mA interface circuits. The amplifier’s low-side common-mode capability is valuable in single-supply transmitter designs, and the 14-TSSOP package keeps four channels compact. Its 1.2 MHz bandwidth is more than adequate for typical process-control loop bandwidths. The implementation must account for output-current capability, load-drive behavior, loop compliance, input offset, and resistor accuracy because those parameters determine the final transmitter accuracy.

🖥️

Test and Measurement Buffering

The LM2902PWR is useful for buffering and level-shifting in general-purpose test equipment where multiple instrument channels must share a compact analog front end. Four independent amplifiers can isolate sources, support gain stages, or generate comparison references. The 26 V nominal operating supply and common-mode input range reaching ground make the device useful for bench circuits powered from a single positive rail, while its 1.2 MHz bandwidth handles low-to-moderate frequency signals. Validate source loading, output swing, input bias current, and settling behavior for the intended measurement bandwidth.

What are the key specifications of LM2902PWR that engineers should know?
The LM2902PWR is a quad general-purpose operational amplifier with four independent channels, a 26 V nominal supply, a 1.2 MHz gain-bandwidth product, and a 14-pin TSSOP package. According to the Texas Instruments LM2902 data sheet, it supports single-supply or split-supply operation and includes a common-mode input range that extends to ground. These characteristics make it suitable for industrial instrumentation, low-frequency filters, audio preamplification, and sensor-conditioning circuits.
Where can I download the LM2902PWR datasheet PDF?
The LM2902PWR datasheet and ordering information are available through the Texas Instruments LM2902 product page at https://www.ti.com/product/LM2902. The manufacturer datasheet is the primary document for the electrical characteristics, 14-TSSOP pin configuration, recommended operating conditions, and typical application circuits. The part-specific ordering page at https://www.ti.com/product/LM2902/part-details/LM2902PWR also identifies the LM2902PWR package option.
Where can I find the LM2902PWR pinout?
The LM2902PWR pinout is defined in the Texas Instruments LM2902 data sheet and corresponds to the 14-pin TSSOP outline. Pins 1 through 7 provide the first amplifier channel and its positive supply connection, pins 8 through 13 provide the remaining channels and the negative supply connection, and pin 14 is the fourth amplifier output. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
Where to buy LM2902PWR online?
Use the Request a Quote form on this page to request LM2902PWR availability, lead time, and a quotation for the exact Texas Instruments MPN. The device is listed as a 14-TSSOP standard general-purpose amplifier, so the request should identify LM2902PWR rather than a related LM2902 package suffix. This avoids ambiguity among LM2902PW, LM2902PWRG4, and other ordering variants.
What is the price of LM2902PWR?
Current commercial terms for LM2902PWR are available through the Request a Quote form on this page. The exact Texas Instruments MPN and required quantity determine the quotation because packaging, order volume, and current inventory affect commercial availability. Request the unit and volume tiers together so sourcing can confirm the appropriate 14-TSSOP configuration and shipment schedule.
What is the lead time for LM2902PWR?
Current lead time and minimum order quantity for LM2902PWR should be confirmed through the Request a Quote form on this page. The device is a standard four-amplifier operational amplifier offered in a 14-TSSOP package, but production status and available inventory can change. Quote requests should state the annual and immediate quantities so the supplier can confirm allocation and delivery timing.
Is LM2902PWR in stock?
Request current LM2902PWR stock status through the Request a Quote form on this page. Stock availability should be checked for the exact 14-TSSOP ordering code LM2902PWR rather than for the broader LM2902 family, which includes multiple package and temperature options. The supplier can confirm quantity, lot consistency, and the expected ship date against your requested schedule.
What can replace LM2902PWR?
LM2902PWR can be replaced by a pin-compatible 14-TSSOP quad operational amplifier that preserves the supply-voltage range, gain-bandwidth product, input-offset class, and channel pinout. The verified alternatives include LM2902PWRG4 and LM2902PW from Texas Instruments, LM2902KPWR from Texas Instruments, and the ROHM Semiconductor LM2902PWR. Confirm the exact electrical limits and exposed-pad arrangement in the manufacturer datasheet before production substitution.
Is LM2902PWR the same as LM2902PW?
LM2902PWR and LM2902PW are both listed as 14-TSSOP versions of the Texas Instruments LM2902, but their ordering suffixes can identify different environmental, quality, or packaging treatment. The LM2902PWR pinout and LM2902PW pinout are therefore the primary interchangeability requirements. Review the ordering table and device-specific quality documentation to confirm whether the alternate suffix satisfies the production requirements of the original assembly.
What is the best ROHM Semiconductor equivalent for LM2902PWR?
The ROHM Semiconductor LM2902PWR is the closest identified cross-brand equivalent because it uses the same LM2902PWR ordering code and is listed in a 14-TSSOP package. According to the manufacturer and distributor product information, it is a standard general-purpose four-circuit amplifier. A drop-in change should still require confirmation of supply range, offset limits, input bias current, slew rate, temperature grade, and footprint tolerances.
LM2902PWR vs LM2902PW - which is better for an industrial control board?
Choose the variant whose ordering details satisfy the board’s environmental and quality requirements rather than deciding only by suffix. Both LM2902PWR and LM2902PW appear as 14-TSSOP LM2902 devices, but the ordering information distinguishes their qualification or packaging treatment. For industrial systems, compare temperature grade, ESD rating, traceability, and lifecycle commitments in the Texas Instruments ordering table before approving either part.
When should I choose LM2902PWR over LM2902PW?
Choose LM2902PWR when the BOM specifically requires that ordering code and the project accepts its associated packaging and quality treatment. Choose LM2902PW when the manufacturer’s ordering table shows that it satisfies the required temperature, compliance, and assembly conditions while supporting the same 14-TSSOP footprint. The deciding factors should be qualification and supply-chain requirements, not an assumed electrical difference between the suffixes.
Is LM2902PWR suitable for single-supply sensor conditioning?
The LM2902PWR is suitable for many single-supply sensor-conditioning circuits because its common-mode input range extends to ground and its supply capability reaches the classic 26 V nominal operating point. It is particularly appropriate for slow sensor signals and general instrumentation where 1.2 MHz bandwidth is sufficient. Check the input and output swing limits, bias-current requirements, and maximum signal level before using it near either supply rail.
What are the main trade-offs of the LM2902PWR compared with precision op amps?
The LM2902PWR prioritizes a 26 V nominal supply, four channels, and general-purpose value rather than precision performance. Compared with a dedicated precision amplifier, its approximately 2 mV offset class and 1.2 MHz bandwidth provide less precision and bandwidth, while its input operating range extending toward ground and high supply tolerance are valuable in industrial circuits. Use it when robustness and voltage range outweigh rail-to-rail precision.
How should LM2902PWR channels be handled when only two amplifiers are needed?
Unused LM2902PWR amplifier channels should be tied to a defined common-mode voltage so that each operational amplifier remains in a stable operating state. A common approach is to connect the non-inverting input to a quiet mid-supply or ground-side bias point while leaving the inverting input connected to the same point through an appropriate feedback arrangement. Follow the manufacturer’s unused-amplifier guidance in the datasheet and schematic notes.

Technische Referenzdaten für LM2902PWR – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose LM2902PWR for a new design that requires four general-purpose amplifier channels, operation from a single positive supply, and a 26 V nominal supply range. Its 1.2 MHz bandwidth is appropriate for low-frequency instrumentation, audio, filtering, and control applications, while the common-mode input range extending to ground simplifies near-ground signal conditioning. LM2902PWRG4 and LM2902PW are practical alternatives when their specific ordering, environmental, or quality treatment better matches the assembly requirements, because they retain the same 14-TSSOP LM2902 architecture. LM2902KPWR can likewise be evaluated as a same-family ordering option. The ROHM Semiconductor LM2902PWR offers a cross-manufacturer sourcing path using the same ordering code and 14-TSSOP format, but its detailed electrical limits should be compared before substitution. Prefer a rail-to-rail precision amplifier when the signal operates close to the upper supply rail, when sub-millivolt offset is critical, or when faster settling is required.

Vergleich mit Alternativen

Parameter Dieses Produkt LM2902PWRG4 LM2902PW LM2902KPWR LM2902PWR
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments ROHM Semiconductor
Package 14-TSSOP 14-TSSOP 14-TSSOP 14-TSSOP 14-TSSOP
Amplifier Count 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits
Product Type General-purpose operational amplifier General-purpose operational amplifier General-purpose operational amplifier General-purpose operational amplifier Standard general-purpose amplifier

Wichtigste Unterscheidungsmerkmale

  • Four independent high-voltage amplifiers in one compact package (vs. LM2902PWRG4)
  • Single-supply-friendly common-mode operation (vs. LM2902PWR)
  • Established 26 V nominal and 36 V maximum supply capability (vs. LM2902PW)

Designhinweise

Place a bypass capacitor close to the V+ pin and use the negative-supply connection as the reference point when the device operates from a single supply. The LM2902PWR is suited to higher-voltage circuits, but the selected capacitor voltage rating must tolerate the maximum rail voltage and any transient overshoot. Verify the exact recommended capacitor value and stability network in the manufacturer datasheet before finalizing the layout.

Route the four amplifier channels to minimize coupling between adjacent inputs and outputs, particularly when one channel handles a high-level signal and another handles a small sensor signal. Keep the TSSOP footprint within the manufacturer’s land-pattern and solder-mask recommendations, inspect the pin-1 orientation, and place the device close to the supply bypass capacitor. Differential input pairs should follow a compact, symmetrical route where practical.

Do not assume that every LM2902 variant is rail-to-rail or precision. The common-mode input range extends to ground, but output swing, input bias current, offset voltage, slew rate, and maximum differential input voltage remain important constraints. For unused channels, connect the inputs in a configuration that keeps the amplifier stable. Review the manufacturer’s recommended unused-circuit diagram rather than leaving an input floating.

The 1.2 MHz gain-bandwidth product is adequate for general low-frequency signal conditioning but limits closed-loop bandwidth and large-signal slew performance. Set the operating gain with the internal compensation characteristics in mind, keep feedback loops short, and verify settling at the signal bandwidth of interest. Add input protection when external sources can exceed the amplifier’s differential or common-mode limits.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The manufacturer and distributor pages identify the device and package, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is present in the cited product information.

Daten verifiziert am: 2026-11-13 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

lm2902pwr datasheet LM2902PWR pinout LM2902PWR datasheet pdf LM2902PWR specifications LM2902PWR equivalent LM2902PWR replacement LM2902PWR vs LM2902PW LM2902PWR 14-TSSOP footprint LM2902PWR price Texas Instruments LM2902PWR LM2902PWR application circuit LM2902PWR 1.2MHz op amp

Verwandte Bauteile & Begriffe

Texas Instruments LM2902PWR LM2902PWRG4 LM2902PW LM2902KPWR ROHM Semiconductor LM2902 LM2902N/PB LM324 LM324ADR operational amplifier quad operational amplifier analog amplifier analog signal-processing IC semiconductor single-supply operation split-supply operation common-mode input range differential input voltage gain-bandwidth product input offset voltage frequency compensation 14-TSSOP TSSOP family surface mount
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen