LM2902PWRE4 - Quad 26V 1.2MHz Op-Amp TSSOP-14 | Texas Instruments
部品番号: LM2902PWRE4 ✓ 生産中LM2902PWRE4 概要
An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. Within the signal-chain hierarchy, it belongs to the amplifier IC family, sitting above discrete transistor stages and below application-specific instrumentation amplifiers. Quad op amps such as the LM2902 integrate four channels in one package, saving board space and matching thermal drift across channels in multi-channel analog circuits.
Key features of the LM2902PWRE4 include a wide supply range (single supply 3V to 26V, or dual supplies up to +/-13V per distributor listing data), low supply current per amplifier, input common-mode range that includes ground (ground-sense operation), and output voltage swing that approaches the negative rail. These characteristics make the family the industry workhorse for single-supply analog front ends. The E4 suffix denotes TI's lead-free, RoHS-compliant tape-and-reel packing of the PW package.
Architecturally, the LM2902 uses a classic bipolar input stage with PNP input transistors that allow input voltages down to the negative rail, which is essential in single-supply designs near 0V. Per TI, the next-generation LM2902B and LM324B versions are drop-in replacements for all versions of the LM224, LM324, and LM2902, with improved specifications such as a 3V to 36V supply range and reduced offset on B/BA versions.
Typical applications include transducer amplification, active filters, comparators and multi-stage signal conditioning in automotive and industrial systems, battery-powered instruments, and DC gain blocks.
Design consideration: the LM2902 is not rail-to-rail at the output or unity-gain stable at high capacitive loads - verify phase margin and output swing headroom in low-voltage designs.
This page synthesizes distributor listings, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet alone.
ドロップイン代替品: LM2902PWRE4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM2902PWRE4 (同一形状・フットプリント) — 相違点: Amplifier Type, Package, RoHS Status, Gain-Bandwidth Product, Number of Amplifiers.
LM2902PWRG3
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902PWRG4
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902KPWE4
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902BPWR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
LM2902YPT
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2902PWRE4 最大定格&電気的特性
| Amplifier Channels | 4 |
| Gain Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV |
| Supply Voltage Range (Single) | 3 V to 26 V |
| Supply Voltage (Dual) | +/-13 V |
| パッケージ | 14-TSSOP (PW) |
| 実装タイプ | Surface Mount |
| Packaging | Tape & Reel (PWR) |
| Amplifier Type | General Purpose |
| RoHS ステータス | Compliant (E4 suffix denotes lead-free) |
| Product Series | LM2902 |
| Drop-in Upgrade Path | LM2902B / LM324B (3V to 36V, lower offset) |
LM2902PWRE4 ピン構成
| ピン 1 | OUT1 — Output of amplifier 1 |
| ピン 2 | IN1- — Inverting input of amplifier 1 |
| ピン 3 | IN1+ — Non-inverting input of amplifier 1 |
| ピン 4 | V+ — Positive supply voltage |
| ピン 5 | IN2+ — Non-inverting input of amplifier 2 |
| ピン 6 | IN2- — Inverting input of amplifier 2 |
| ピン 7 | OUT2 — Output of amplifier 2 |
| ピン 8 | OUT3 — Output of amplifier 3 |
| ピン 9 | IN3- — Inverting input of amplifier 3 |
| ピン 10 | IN3+ — Non-inverting input of amplifier 3 |
| ピン 11 | V- / GND — Negative supply (dual supply) or ground (single supply) |
| ピン 12 | IN4+ — Non-inverting input of amplifier 4 |
| ピン 13 | IN4- — Inverting input of amplifier 4 |
| ピン 14 | OUT4 — Output of amplifier 4 |
主な用途
LM2902PWRE4 の用途: 6 件s: Automotive Sensor Signal Conditioning, Industrial Current-Sense and Monitoring Front Ends, Battery-Powered Portable Instruments, Active Filters and Signal Conditioning, Audio Signal Routing and Mixing, Comparator and Threshold Detection Circuits.
Automotive Sensor Signal Conditioning
The LM2902PWRE4 fits automotive sensor conditioning because the LM2902 line is TI's automotive/industrial grade of the LM324 quad op amp, offering 26V supply tolerance that survives 12V battery transients and a 2 mV offset adequate for resistive and inductive sensor bridges. Its ground-sensing input common-mode range allows amplification of signals referenced to chassis ground without negative supplies. In a typical channel, the op amp amplifies a throttle-position or pressure-sensor output by a gain of 10 to 50 before the ADC, consuming only the bandwidth needed (1.2 MHz GBW supports gains up to about 50 at audio-band signals). Four channels in one TSSOP-14 reduce component count and channel-to-channel thermal mismatch. TI recommends the next-generation LM2902B as a drop-in upgrade with 36V transient tolerance.
おすすめ
Industrial Current-Sense and Monitoring Front Ends
In industrial equipment the LM2902PWRE4 serves as a low-cost multi-channel front end for current-sense amplification, 4-20 mA loop conditioning, and monitoring circuits on 24V rails. The 26V single-supply rating allows direct connection to nominal 24V industrial supplies with margin, and the four independent amplifiers implement sense, reference, and filter stages in a single package. Its ground-sensing inputs measure shunt voltages near 0V, while the 1.2 MHz bandwidth comfortably handles control-loop signals well below 100 kHz. The 2 mV offset dominates accuracy at small shunt voltages, so for sub-100 mV full-scale shunts calibrate digitally or select the improved-offset LM2902B BA grade. The TSSOP-14 footprint keeps the analog front end compact on crowded control boards.
おすすめ
Battery-Powered Portable Instruments
The LM2902PWRE4 suits battery-powered instruments because it operates from a single 3V supply up to 26V and its inputs sense signals at ground potential, letting designers amplify small transducer outputs without a negative rail or charge pump. The quad integration provides four gain/filter/buffer stages from one package, and the low per-channel supply current typical of the bipolar LM2902 family preserves battery life in multichannel meters, DMM front ends, and environmental sensors. The 1.2 MHz gain-bandwidth product covers low-frequency measurement signals with stable closed-loop gains up to several hundred. Designers should budget for the 2 mV input offset when measuring microvolt-level signals, and the TSSOP-14 package supports dense two-layer layouts common in portable electronics.
おすすめ
Active Filters and Signal Conditioning
Active low-pass, band-pass, and Sallen-Key filters are a classic LM2902 application: the 1.2 MHz gain-bandwidth product supports filter corner frequencies up to roughly 10-20 kHz with accurate Q, since the GBW should exceed the corner frequency by at least 50-100x for predictable response. Four amplifiers per TSSOP-14 package allow multi-stage filters (typically four poles) in one device with matched thermal drift between stages. The ground-sensing inputs simplify single-supply filter biasing by referencing the virtual ground to mid-supply or to ground for DC-coupled designs. Designers must respect the output swing limits - not rail-to-rail - when setting filter gain and supply headroom. For low-voltage 3.3V systems with signals near the positive rail, a rail-to-rail quad such as the TS974 is a stronger choice.
おすすめ
Audio Signal Routing and Mixing
The LM2902PWRE4 works in consumer and industrial audio front ends where its 1.2 MHz bandwidth covers the full audio band with ample loop gain: at 20 kHz the open-loop gain remains high enough for low distortion in gains up to about 20 dB. Quad integration suits mixing consoles and multichannel preamplifiers, with one TSSOP-14 providing four summing or buffer stages. The ground-sensing input range handles AC-coupled and ground-referenced sources in single-supply audio designs at 12V or 24V. Because the output stage is not rail-to-rail, keep signal swings within roughly 1.5V of each rail to avoid clipping distortion. For hi-fi applications demanding lower noise and offset, TI's precision audio op amps outperform this general-purpose part, but for cost-driven audio control circuitry the LM2902 remains a standard choice.
おすすめ
Comparator and Threshold Detection Circuits
Although not a dedicated comparator, the LM2902PWRE4 is widely used as a low-speed comparator and window detector in cost-sensitive industrial and automotive boards: its ground-sensing inputs allow thresholds referenced to ground, and the open-collector-like output swing behavior near the negative rail simplifies interfacing to logic in single-supply systems. Four amplifiers enable multi-threshold monitoring - undervoltage, overvoltage, and two alarm levels - from one package. Response time is limited by the 1.2 MHz bandwidth and output slew behavior, so this application is restricted to slow events (milliseconds) such as battery-level supervision and fault latching, not fast switching. TI application guidance recommends adding hysteresis with a feedback resistor because, unlike true comparators, op amps have no internal hysteresis.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM2902PWRE4 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM2902PWR | LM2902PWRG4 | LM2902KPWE4 | LM2902YPT |
|---|---|---|---|---|---|
| Package | 14-TSSOP (PW) | 14-TSSOP (PW) - same | 14-TSSOP (PW) - same | 14-TSSOP (PW) - same | 14-TSSOP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics |
| Channels | 4 | 4 | 4 | 4 | 4 |
| Gain Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Drop-in Upgrade Path | LM2902B (3V-36V, lower offset) | LM2902B (same) | LM2902B (same) | LM2902B (same) | ST automotive-grade LM2902 variants |
| RoHS Compliance | Compliant (E4 suffix) | Compliant | Compliant (G4 = green packing) | Compliant (E4 suffix) | Compliant |
主な差別化要因
- Improved-offset drop-in upgrade available (vs LM2902BPWR)
- Ground-sensing bipolar inputs (vs TS974IDT)
- Multi-vendor second sourcing (vs LM2902YPT)
設計ノート
Do not treat the LM2902 as rail-to-rail: the input common-mode range includes the negative rail but stops short of the positive rail, and the output saturates well below the positive rail at load. Circuits biased near the positive rail will clip or lose phase margin. Also remember the 2 mV typical offset - at gains above 100, offset contributes over 200 mV of output error, so either calibrate digitally or select the improved-offset LM2902B BA grade for precision channels.
Place a 100 nF ceramic decoupling capacitor within a few millimeters of the V+ pin (pin 4) to the ground/negative-supply pin (pin 11), plus bulk 10 uF at the board level. Because the four amplifiers share one supply pair, fast switching on one channel can couple into others - keep high-current or comparator channels away from precision gain channels, and route sensitive input traces short with guard ground pours. The TSSOP-14 has no exposed pad, so thermal relief relies on trace copper.
The 1.2 MHz gain-bandwidth product requires closed-loop bandwidth to stay below roughly 1/50 of GBW for flat, low-peak response; at gain 10, expect about 120 kHz usable bandwidth with mild peaking unless compensated. Driving capacitive loads directly (cables, long traces) reduces phase margin - isolate with a small series resistor (typically 50-100 ohm) at the output. Verify stability in simulation for gains above 50 or filter Q above 2.
Estimated: in single-supply use, dissipation per channel is roughly V+ times the quiescent current plus load current times output swing headroom; at 26V supply with light loads this stays well within the TSSOP-14 thermal capability, but four channels driving resistive loads near the positive rail simultaneously raises die temperature - check the datasheet theta-JA against your ambient maximum before finalizing the layout.
コンプライアンス情報
The E4 suffix denotes TI's RoHS-compliant, lead-free tape-and-reel ordering option. AEC-Q100 qualification status for this specific orderable should be confirmed on the TI quality page.