LM2904AN - Dual Op-Amp, 3-26V Single Supply | onsemi
部品番号: LM2904AN ✓ 生産中LM2904AN 概要
A dual operational amplifier is an analog integrated circuit that houses two complete op-amp cores on a single silicon die, sharing one set of supply pins. In the voltage-regulator-to-amplifier hierarchy of signal-chain components, the op-amp sits between the passive components and the dedicated precision amplifier or instrumentation amplifier: it performs gain, buffering, filtering, and comparison functions that passive networks alone cannot achieve. Single-supply op-amps like the LM2904AN are designed so their input common-mode range includes the negative rail, simplifying circuits powered from a single positive rail such as 5V, 12V, or 24V industrial supplies.
Key features of the LM2904AN include low power drain, single-supply or split-supply operation, input common-mode range extending down to the negative rail, and the industry-standard DIP-8 pinout shared across the LM358/LM2904 family. The wide 3V to 26V supply range covers 5V logic systems, 12V automotive rails, and 24V industrial buses without redesign.
Technically, the two amplifiers are matched on a common substrate, ensuring closely tracking parameters over temperature. The output stage is designed for single-supply operation where the output can swing close to ground under light loads. Because the LM2904 is a low-cost, general-purpose part, designers should observe its class-B output behavior near the lower rail and its moderate slew rate when applying it to high-frequency or precision tasks.
Typical applications include industrial sensor signal conditioning, transducer amplifier front ends, DC gain blocks, active filters, comparators with hysteresis, and low-frequency audio preamplifiers in through-hole prototypes and repair work where the PDIP package simplifies hand soldering and socketing.
For design, provide adequate supply decoupling (100 nF ceramic close to pin 8 and pin 4) and avoid capacitive loads above roughly 100 pF without series isolation resistance to prevent oscillation.
This page adds value beyond the manufacturer datasheet by combining distributor availability data, drop-in alternatives, a parametric comparison table, and practical design notes in one place.
ドロップイン代替品: LM2904AN — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM2904AN (同一形状・フットプリント) — 相違点: Package, Mounting Type, Amplifier Type, Slew Rate, Gain Bandwidth Product.
LM2904NG
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →LM258AN
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →LM358AN
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2904DR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2904BIDR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2904AN 最大定格&電気的特性
| Amplifier Type | Standard (General Purpose) |
| Number of Circuits | 2 |
| Supply Voltage Range | 3 V to 26 V |
| Gain Bandwidth Product | 700 kHz (per TI LM2904 product page) |
| Single Supply Operation | Yes |
| Split Supply Operation | Yes |
| Input Common-Mode Range | Extends to ground/VEE |
| Power Drain | Low power (per onsemi datasheet) |
| パッケージ | 8-PDIP (DIP-8) |
| 実装タイプ | Through Hole |
| Datasheet Length | 14 pages (137 Kbytes, onsemi datasheet) |
LM2904AN ピン構成
| ピン 1 | OUT1 — Amplifier 1 output |
| ピン 2 | IN1- — Amplifier 1 inverting input |
| ピン 3 | IN1+ — Amplifier 1 non-inverting input |
| ピン 4 | GND/VEE — Negative supply or ground |
| ピン 5 | IN2+ — Amplifier 2 non-inverting input |
| ピン 6 | IN2- — Amplifier 2 inverting input |
| ピン 7 | OUT2 — Amplifier 2 output |
| ピン 8 | VCC — Positive supply, 3 V to 26 V |
主な用途
LM2904AN の用途: 6 件s: Industrial Sensor Signal Conditioning, Transducer Amplifier Front Ends, Active Filters and Low-Frequency Signal Chains, Comparator and Threshold Detection Circuits, Through-Hole Prototyping, Repair and Education, Low-Frequency Audio Preamplification.
Industrial Sensor Signal Conditioning
The LM2904AN fits industrial sensor front ends because its 3V to 26V supply range covers standard 24V control-panel rails and 5V logic rails alike, and its input common-mode range extending to ground/VEE lets it amplify transducer signals referenced to 0V without a negative supply. One DIP-8 package provides two matched amplifiers, so a typical channel can use amplifier A as a gain stage (for example, gain of 10 with 10k/100k resistors) while amplifier B implements a second-order active filter or a comparator with hysteresis for alarm thresholds. In a 24V-powered design, headroom to 26V leaves margin for supply transients. The through-hole PDIP package also simplifies replacement during panel maintenance, where socketed through-hole parts are still common practice.
おすすめ
Transducer Amplifier Front Ends
Bridge and current-loop transducers benefit from the LM2904AN's ability to operate with inputs near the negative rail, a defining feature of the LM2904 class per the onsemi datasheet description. A pressure or light-sensor bridge output that swings only millivolts above ground can be amplified directly with a non-inverting configuration, something bipolar-input op-amps with limited common-mode range cannot do on a single supply. The low power drain matters in distributed I/O modules where many channels share one supply budget. Designers should account for the LM2904 class offset voltage when amplifying sub-10mV signals, adding trimming or choosing a chopper-stabilized alternative where measurement accuracy demands it.
おすすめ
Active Filters and Low-Frequency Signal Chains
With roughly 700 kHz of gain-bandwidth per the TI LM2904 family data, the LM2904AN supports Sallen-Key and multiple-feedback active filters up to corner frequencies in the tens of kilohertz at moderate Q. One package implements a two-pole low-pass filter using both amplifiers in cascade, saving board area and ensuring the two filter sections track over temperature because they share the die. The wide 3V to 26V range lets the same filter design serve 5V microcontroller front ends and 24V industrial signal chains. For audio-band anti-alias filtering ahead of an ADC, the bandwidth is ample; for filters above about 100 kHz, select a wider-bandwidth dual amplifier instead.
おすすめ
Comparator and Threshold Detection Circuits
Although dedicated comparators switch faster, the LM2904AN is widely used as a comparator with hysteresis in slow alarm and level-detection circuits because the two amplifiers in one DIP-8 package can implement both the sensing threshold and the reference buffer. Its input common-mode range to ground allows sensing near 0V, and the 26V maximum supply permits direct connection to 24V industrial signals without dividers. The trade-off versus a true comparator such as the LM2901 family is slower response and no open-collector output, so designs requiring fast, defined logic-level outputs should use a dedicated comparator while level-monitoring tasks up to a few kilohertz are well served by the LM2904AN.
おすすめ
Through-Hole Prototyping, Repair and Education
The 8-pin PDIP through-hole package is the decisive advantage for breadboarding, educational laboratories, and legacy equipment repair: the 0.1-inch pin pitch inserts directly into breadboards and DIP sockets without adapters, unlike SOIC or VSSOP surface-mount equivalents. Because the LM2904 pinout is an industry standard shared with LM358-type parts, a stocked LM2904AN can service thousands of legacy audio, instrumentation and consumer boards whose schematics assume the classic dual op-amp pin arrangement. For repair shops the 3V to 26V range means one drawer part covers battery-powered devices, 12V automotive accessories, and 24V industrial equipment alike, reducing inventory diversity.
おすすめ
Low-Frequency Audio Preamplification
For microphone and line-level preamplification in cost-driven or legacy designs, the LM2904AN provides two gain stages per package with adequate bandwidth for the full audio band: at a closed-loop gain of 10 the roughly 700 kHz gain-bandwidth yields about 70 kHz of usable bandwidth, comfortably covering 20 Hz to 20 kHz. The single-supply operation from a 12V or 24V rail simplifies power architecture in intercoms, paging systems, and automotive-adjacent audio accessories, with inputs biased to mid-supply via a resistor divider. Designers sensitive to noise and crossover distortion near the negative rail should bias outputs away from the rail or select the lower-noise alternatives listed here for demanding listening applications.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM2904AN — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM2904NG | LM258AN | LM358AN | LM2904B |
|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Package | 8-PDIP (DIP-8) | 8-PDIP (DIP-8) - same | 8-PDIP (DIP-8) - same | 8-PDIP (DIP-8) - same | 8-PDIP (DIP-8) - same |
| Number of Circuits | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage Range | 3 V to 26 V | 3 V to 26 V | 3 V to 32 V | 3 V to 32 V | 2.7 V to 36 V |
| Gain Bandwidth Product | ~700 kHz | ~700 kHz | ~1 MHz | ~1 MHz | ~1.2 MHz |
| Temperature Grade | Extended industrial (LM2904 A-grade) | Industrial | Commercial | Commercial | Industrial (LM2904B grade) |
| Performance Class | Original LM2904 generation | Original LM2904 generation | Original LM258 generation | Original LM358 generation | Enhanced (improved offset and drive) |
| Input Common-Mode Range | Extends to ground/VEE | Extends to ground/VEE | Extends to ground/VEE | Extends to ground/VEE | Extends to ground/VEE |
主な差別化要因
- Extended industrial temperature grade in standard DIP-8 (vs LM358AN)
- Onsemi second-source continuity (vs LM2904)
- Original-generation cost vs enhanced performance (vs LM2904B)
設計ノート
Decouple the LM2904AN supply with a 100 nF ceramic capacitor placed within a few millimeters of pin 8 (VCC) and pin 4 (GND/VEE), plus 4.7 uF to 10 uF of bulk capacitance per board. Because the dual amplifiers share one supply pair, fast switching on one channel can couple into the other through supply impedance; the local ceramic capacitor suppresses this cross-talk. Never exceed the 26 V maximum supply in the onsemi part, and observe that in split-supply use each rail pair must still respect the total supply window.
The LM2904 class output stage behaves as a class-AB/class-B stage: it sources current well but sinks weakly near the lower rail, so outputs intended to reach 0V need a pull-down resistor (typically 2k to 10k to ground) to avoid a dead-zone distortion of a few hundred millivolts. Also avoid direct capacitive loads above roughly 100 pF; add a 50 to 200 ohm series resistor between output and cable capacitance to prevent oscillation. Finally, check phase reversal limits: inputs should not be pulled more than a diode drop below VEE.
For through-hole DIP-8 layouts, keep feedback resistor paths short and route the high-impedance inverting-input traces away from output traces of the adjacent amplifier to minimize crosstalk on the shared die. Use a ground plane on the component-side under the part where practical. For single-supply designs, bias input dividers from a well-decoupled node, and consider AC-coupling with a mid-supply virtual ground for audio signals. Estimated: at a gain of 10 with 10k/100k feedback resistors, input-referred noise is dominated by resistor thermal noise above the op-amp's own contribution.
コンプライアンス情報
Compliance status was not stated in the retrieved distributor snippets; confirm RoHS/REACH status on the onsemi product page before ordering for regulated markets.