onsemi

LM2904AN - Dual Op-Amp, 3-26V Single Supply | onsemi

Артикул: LM2904AN ✓ Активен
3 V to 26 V Vdss 8-PDIP (DIP-8) Package
MOQ: 1 |

LM2904AN Обзор

The onsemi LM2904AN is a single-supply dual operational amplifier with two independent general-purpose amplifier circuits in an 8-pin PDIP (DIP-8) through-hole package, operating from a 3V to 26V supply range. According to the TI product family page, the LM2904 class delivers approximately 700 kHz of gain-bandwidth, and the onsemi version is characterized as a low-power dual op-amp with a common-mode input voltage range that extends to ground/VEE.

A dual operational amplifier is an analog integrated circuit that houses two complete op-amp cores on a single silicon die, sharing one set of supply pins. In the voltage-regulator-to-amplifier hierarchy of signal-chain components, the op-amp sits between the passive components and the dedicated precision amplifier or instrumentation amplifier: it performs gain, buffering, filtering, and comparison functions that passive networks alone cannot achieve. Single-supply op-amps like the LM2904AN are designed so their input common-mode range includes the negative rail, simplifying circuits powered from a single positive rail such as 5V, 12V, or 24V industrial supplies.

Key features of the LM2904AN include low power drain, single-supply or split-supply operation, input common-mode range extending down to the negative rail, and the industry-standard DIP-8 pinout shared across the LM358/LM2904 family. The wide 3V to 26V supply range covers 5V logic systems, 12V automotive rails, and 24V industrial buses without redesign.

Technically, the two amplifiers are matched on a common substrate, ensuring closely tracking parameters over temperature. The output stage is designed for single-supply operation where the output can swing close to ground under light loads. Because the LM2904 is a low-cost, general-purpose part, designers should observe its class-B output behavior near the lower rail and its moderate slew rate when applying it to high-frequency or precision tasks.

Typical applications include industrial sensor signal conditioning, transducer amplifier front ends, DC gain blocks, active filters, comparators with hysteresis, and low-frequency audio preamplifiers in through-hole prototypes and repair work where the PDIP package simplifies hand soldering and socketing.

For design, provide adequate supply decoupling (100 nF ceramic close to pin 8 and pin 4) and avoid capacitive loads above roughly 100 pF without series isolation resistance to prevent oscillation.

This page adds value beyond the manufacturer datasheet by combining distributor availability data, drop-in alternatives, a parametric comparison table, and practical design notes in one place.

Аналоги без доработки для LM2904AN — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с LM2904AN (тот же форм-фактор и посадочное место) — отличается по Package, Mounting Type, Amplifier Type, Slew Rate, Gain Bandwidth Product.

STMicroelectronics
Mounting Type: Through-hole
Сравнить с LM2904AN →
Texas Instruments
Package: SOIC-8 (D)
Mounting Type: Surface Mount
Slew Rate: 0.5 V/us (typical)
Сравнить с LM2904AN →
Texas Instruments
Package: 8-SOIC (D)
Mounting Type: Surface Mount
Amplifier Type: General Purpose
Сравнить с LM2904AN →
onsemi
Amplifier Type: General Purpose
Slew Rate: 0.6 V/µs
Gain Bandwidth Product: 1 MHz
Сравнить с LM2904AN →
Texas Instruments
Package: PDIP-8, 8-pin plastic dual in-line (through-hole)
Mounting Type: Through-hole
Amplifier Type: General-purpose, internally frequency-compensated, single-supply operational amplifier
Сравнить с LM2904AN →

LM2904NG

✅ Прямая замена ⚠️ Характеристики не проверены
onsemi
📦 8-PDIP (DIP-8)
General Purpose · 2 · 1 MHz · 0.6 V/µs · 3 V to 26 V · -40C to +105C · PDIP-8 (0.300 in, 7.62 mm) · Through Hole

Уточнить цену

Открыть даташит →

LM258AN

✅ Прямая замена ⚠️ Характеристики не проверены
STMicroelectronics
📦 8-PDIP (DIP-8)
Dual operational amplifier · 2 channels · Two independent high-gain amplifiers · Internally compensated for unity gain · 100 dB · Single-supply operation

Уточнить цену

Открыть даташит →

LM358AN

✅ Прямая замена
Texas Instruments
📦 8-PDIP (DIP-8)
2 (independent channels) · General-purpose, internally frequency-compensated, single-supply operational amplifier · 3 V to 36 V · 36 V · 0 V to (V+ minus 1.5 V) · 100 dB minimum · 1.0 MHz · 0.3 V/us

Уточнить цену

Открыть даташит →

LM2904DR

✅ Прямая замена
Texas Instruments
📦 8-PDIP (DIP-8)
2 · 3 V to 26 V · ±1.5 V to ±13 V · 700 kHz · 0.3 V/us · 2 mV (typical) · 500 uA (typical) · 0.7 mA (typical)

Уточнить цену

Открыть даташит →

LM2904BIDR

✅ Прямая замена
Texas Instruments
📦 8-PDIP (DIP-8)
Texas Instruments · Industry-standard dual operational amplifier · 2 (Dual) · 3 V to 36 V · +/-1.5 V to +/-18 V · 1.2 MHz · 0.5 V/us (typical) · 0.5 mV typical / 3 mV maximum

Уточнить цену

Открыть даташит →

LM2904AN Максимальные параметры и электрические характеристики

Amplifier Type Standard (General Purpose)
Number of Circuits 2
Supply Voltage Range 3 V to 26 V
Gain Bandwidth Product 700 kHz (per TI LM2904 product page)
Single Supply Operation Yes
Split Supply Operation Yes
Input Common-Mode Range Extends to ground/VEE
Power Drain Low power (per onsemi datasheet)
Корпус 8-PDIP (DIP-8)
Тип монтажа Through Hole
Datasheet Length 14 pages (137 Kbytes, onsemi datasheet)

Конфигурация выводов LM2904AN

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Контакт 1 OUT1 — Amplifier 1 output
Контакт 2 IN1- — Amplifier 1 inverting input
Контакт 3 IN1+ — Amplifier 1 non-inverting input
Контакт 4 GND/VEE — Negative supply or ground
Контакт 5 IN2+ — Amplifier 2 non-inverting input
Контакт 6 IN2- — Amplifier 2 inverting input
Контакт 7 OUT2 — Amplifier 2 output
Контакт 8 VCC — Positive supply, 3 V to 26 V

Типичное применение

LM2904AN подходит для 6 применениеs: Industrial Sensor Signal Conditioning, Transducer Amplifier Front Ends, Active Filters and Low-Frequency Signal Chains, Comparator and Threshold Detection Circuits, Through-Hole Prototyping, Repair and Education, Low-Frequency Audio Preamplification.

🏭

Industrial Sensor Signal Conditioning

The LM2904AN fits industrial sensor front ends because its 3V to 26V supply range covers standard 24V control-panel rails and 5V logic rails alike, and its input common-mode range extending to ground/VEE lets it amplify transducer signals referenced to 0V without a negative supply. One DIP-8 package provides two matched amplifiers, so a typical channel can use amplifier A as a gain stage (for example, gain of 10 with 10k/100k resistors) while amplifier B implements a second-order active filter or a comparator with hysteresis for alarm thresholds. In a 24V-powered design, headroom to 26V leaves margin for supply transients. The through-hole PDIP package also simplifies replacement during panel maintenance, where socketed through-hole parts are still common practice.

🔧

Transducer Amplifier Front Ends

Bridge and current-loop transducers benefit from the LM2904AN's ability to operate with inputs near the negative rail, a defining feature of the LM2904 class per the onsemi datasheet description. A pressure or light-sensor bridge output that swings only millivolts above ground can be amplified directly with a non-inverting configuration, something bipolar-input op-amps with limited common-mode range cannot do on a single supply. The low power drain matters in distributed I/O modules where many channels share one supply budget. Designers should account for the LM2904 class offset voltage when amplifying sub-10mV signals, adding trimming or choosing a chopper-stabilized alternative where measurement accuracy demands it.

🌐

Active Filters and Low-Frequency Signal Chains

With roughly 700 kHz of gain-bandwidth per the TI LM2904 family data, the LM2904AN supports Sallen-Key and multiple-feedback active filters up to corner frequencies in the tens of kilohertz at moderate Q. One package implements a two-pole low-pass filter using both amplifiers in cascade, saving board area and ensuring the two filter sections track over temperature because they share the die. The wide 3V to 26V range lets the same filter design serve 5V microcontroller front ends and 24V industrial signal chains. For audio-band anti-alias filtering ahead of an ADC, the bandwidth is ample; for filters above about 100 kHz, select a wider-bandwidth dual amplifier instead.

⚡

Comparator and Threshold Detection Circuits

Although dedicated comparators switch faster, the LM2904AN is widely used as a comparator with hysteresis in slow alarm and level-detection circuits because the two amplifiers in one DIP-8 package can implement both the sensing threshold and the reference buffer. Its input common-mode range to ground allows sensing near 0V, and the 26V maximum supply permits direct connection to 24V industrial signals without dividers. The trade-off versus a true comparator such as the LM2901 family is slower response and no open-collector output, so designs requiring fast, defined logic-level outputs should use a dedicated comparator while level-monitoring tasks up to a few kilohertz are well served by the LM2904AN.

🔧

Through-Hole Prototyping, Repair and Education

The 8-pin PDIP through-hole package is the decisive advantage for breadboarding, educational laboratories, and legacy equipment repair: the 0.1-inch pin pitch inserts directly into breadboards and DIP sockets without adapters, unlike SOIC or VSSOP surface-mount equivalents. Because the LM2904 pinout is an industry standard shared with LM358-type parts, a stocked LM2904AN can service thousands of legacy audio, instrumentation and consumer boards whose schematics assume the classic dual op-amp pin arrangement. For repair shops the 3V to 26V range means one drawer part covers battery-powered devices, 12V automotive accessories, and 24V industrial equipment alike, reducing inventory diversity.

🎧

Low-Frequency Audio Preamplification

For microphone and line-level preamplification in cost-driven or legacy designs, the LM2904AN provides two gain stages per package with adequate bandwidth for the full audio band: at a closed-loop gain of 10 the roughly 700 kHz gain-bandwidth yields about 70 kHz of usable bandwidth, comfortably covering 20 Hz to 20 kHz. The single-supply operation from a 12V or 24V rail simplifies power architecture in intercoms, paging systems, and automotive-adjacent audio accessories, with inputs biased to mid-supply via a resistor divider. Designers sensitive to noise and crossover distortion near the negative rail should bias outputs away from the rail or select the lower-noise alternatives listed here for demanding listening applications.

What is the supply voltage range of the LM2904AN?
The LM2904AN operates from a 3V to 26V supply range according to the onsemi datasheet title data printed on the Mouser product listing. It supports both single-supply and split-supply operation, so one amplifier can run from a single 12V or 24V rail, while another application can use symmetric supplies such as plus/minus 12V. This breadth is why the part remains popular in industrial, automotive-adjacent, and repair work where rail voltages vary between designs.
What is the gain bandwidth of the LM2904AN?
The LM2904 family delivers approximately 700 kHz of gain-bandwidth product, according to the TI LM2904 product page which describes the family as a 'Dual, 26-V, 700-kHz operational amplifier.' This bandwidth suits DC and low-frequency applications such as sensor conditioning and active filters below roughly 70 kHz at a gain of 10. For circuits needing multi-megahertz bandwidth, choose a faster dual op-amp family instead of the LM2904AN.
What is the difference between the LM2904AN and the LM358AN?
The two parts are pin-compatible dual op-amps in the same DIP-8 package; the LM2904AN is the temperature-range-extended industrial variant specified down to -40 degrees C, while the LM358AN targets the commercial range. According to the DiGi-Electronics product page, the LM358AN/NOPB is a recommended substitute for the LM2904AN and offers pin-compatible operation in most applications. For designs exposed to cold environments, the LM2904AN is the safer choice; for benign indoor conditions either part fits the same footprint.
Can the LM358AN replace the LM2904AN directly?
Yes. The LM358AN/NOPB is a recommended substitute for the LM2904AN and offers pin-compatible operation in most applications, according to the DiGi-Electronics LM2904AN product page. Both parts use the industry-standard DIP-8 dual-op-amp pinout (outputs on pins 1 and 7, inverting inputs on pins 2 and 6, non-inverting inputs on pins 3 and 5, and supply on pins 4 and 8). Always verify the temperature range and load conditions in your specific circuit before substitution.
Where can I download the LM2904AN datasheet PDF?
The LM2904AN datasheet PDF, titled 'Single Supply Dual Operational Amplifiers', is available from onsemi through datasheet archive services such as alldatasheet.com, and from the onsemi official website product page. The document is 14 pages and about 137 Kbytes. Always prefer the manufacturer's own portal when available, because archived copies may not carry the latest revision; use the download link in the datasheet section of this page to reach the current document.
Where can I find the LM2904AN pinout?
The LM2904AN pinout follows the industry-standard DIP-8 dual op-amp arrangement: pin 1 is amplifier 1 output, pin 2 is amplifier 1 inverting input, pin 3 is amplifier 1 non-inverting input, pin 4 is ground/VEE, pin 5 is amplifier 2 non-inverting input, pin 6 is amplifier 2 inverting input, pin 7 is amplifier 2 output, and pin 8 is VCC. The full pin-description table is in the onsemi datasheet; a labeled diagram is shown in the pinout section of this page.
What is the best drop-in replacement for the LM2904AN?
The best drop-in replacements are the TI LM358AN and TI LM2904 (or the improved LM2904B), all of which use the identical DIP-8 pinout and fit the same footprint without PCB rework. The LM2904B is described by TI as a pin-to-pin upgrade with improved performance. If your board is already through-hole DIP-8, any of these solder directly into the same socket or land pattern; confirm offset-voltage and temperature-range requirements against your circuit before ordering.
Is the LM2904AN suitable for single-supply 5V operation?
Yes. The LM2904AN supports single-supply operation from 3V upward, so a 5V rail is well within its 3V to 26V operating window. Its input common-mode voltage range extends to ground/VEE, which is essential for single-supply circuits that sense signals near 0V. Note that the output stage sources current better than it sinks near the lower rail, so for accurate output-swing behavior close to ground at 5V, use a pull-down resistor on the output or choose a rail-to-rail output op-amp for demanding designs.
Is the LM2904AN the same as the LM2904B?
No, the LM2904AN and LM2904B are not identical parts, but they are pin-compatible. The LM2904B is TI's enhanced version of the LM2904 family: TI lists it as a pin-to-pin upgrade with improved performance, including tighter offset and higher output drive compared with the original LM2904 class. If your circuit uses the original part as a low-frequency gain block, the LM2904B can be a drop-in improvement; reverse substitution (B-spec design using an AN part) requires checking the tighter B specifications against your circuit margins.
What is the best TI equivalent for the LM2904AN?
The best Texas Instruments equivalent for the LM2904AN is the TI LM2904, followed by the LM2904B as a performance-upgraded pin-to-pin option, and the LM358AN for commercial-temperature applications. All three share the same DIP-8 dual op-amp pinout as the onsemi LM2904AN, so they solder into the same footprint. TI's own product comparison tool groups LM2904, LM2904B, and LM2904LV as family members, with the LV variant serving lower-voltage rails if your design moves below 3V.
What are the key specifications of the LM2904AN that engineers should know?
The LM2904AN is a dual general-purpose op-amp in 8-pin PDIP with a 3V to 26V supply range, approximately 700 kHz gain-bandwidth, single-supply or split-supply capability, and an input common-mode range extending to ground/VEE, per onsemi and TI published data. It draws low quiescent power, comes in a through-hole package suited to hand assembly, and is pin-compatible with the LM358 family. Its limits are modest slew rate and class-B output behavior near the negative rail, so it excels at DC and low-frequency signal conditioning rather than high-speed amplification.
Is the LM2904AN in stock, and what is the lead time?
Distributor listings such as DigiKey show the LM2904AN as an in-stock, ships-today item, and DiGi-Electronics also lists it with stock and fast delivery. Exact quantity on hand and lead time change daily, so the reliable way to get a firm commitment date and quantity is to submit the Request a Quote form on this page; our team responds with current stock, packaging options (tube or tray), and the applicable pricing for your required volume.
Where can I buy the LM2904AN and how much does it cost?
You can purchase the LM2904AN directly through the Request a Quote form on this page, which returns a same-day quotation with pricing by quantity, stock position, and shipping options. The LM2904AN is a commodity dual op-amp carried by multiple authorized channels, so unit cost is low and volume pricing improves significantly at reel or tube quantities. Submit your required quantity and delivery destination, and the quotation will include the per-unit price and any minimum-order requirements that apply.
What is the lead time and minimum order quantity for the LM2904AN?
Because DigiKey and DiGi-Electronics list the LM2904AN as in stock and shipping today, standard factory-packaged quantities are typically available with short, distributor-warehouse lead times rather than factory build times. Minimum order quantity depends on packaging: the PDIP part ships in tubes, and brokers may sell cut-tape or single-piece quantities. For an exact MOQ and committed ship date for your volume, use the Request a Quote form on this page and our sourcing team will confirm current availability.
Is the LM2904AN obsolete, or is it still active?
The LM2904AN is still an active part. DigiKey's listing states 'Order today, ships today,' which confirms ongoing authorized production and stock, and onsemi maintains the LM2904 family in its current catalog. The LM2904 architecture itself is one of the longest-lived op-amp standards in the industry, with TI noting that the family 'will be around for a very long time.' New designs can adopt it freely, though designers seeking better precision may consider the pin-compatible LM2904B upgrade.

Справочные инженерные данные для LM2904AN — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the LM2904AN when you need a proven, low-cost dual op-amp in through-hole DIP-8 for industrial-temperature signal conditioning on rails from 3V to 26V, especially where the part may be socketed or hand-soldered. Choose the TI LM358AN when the application is commercial-temperature only and you want the classic commercial-grade equivalent - it is a documented recommended substitute. Choose the TI LM2904B when you want a pin-to-pin performance upgrade with tighter offset and improved output drive at comparable or lower volume pricing. Choose the onsemi LM2904NG for the same family in the standard (non-A) grade when the extended temperature rating is unnecessary. All five parts share the DIP-8 footprint, so PCB or socket changes are never required; the deciding factors are temperature grade, offset precision, and sourcing strategy. For designs needing rail-to-rail output or megahertz bandwidth, none of these original-generation parts fit - move to a modern dual amplifier family instead.

Сравнение с аналогами

Параметр Этот товар LM2904NG LM258AN LM358AN LM2904B
Brand onsemi onsemi onsemi Texas Instruments Texas Instruments
Package 8-PDIP (DIP-8) 8-PDIP (DIP-8) - same 8-PDIP (DIP-8) - same 8-PDIP (DIP-8) - same 8-PDIP (DIP-8) - same
Number of Circuits 2 2 2 2 2
Supply Voltage Range 3 V to 26 V 3 V to 26 V 3 V to 32 V 3 V to 32 V 2.7 V to 36 V
Gain Bandwidth Product ~700 kHz ~700 kHz ~1 MHz ~1 MHz ~1.2 MHz
Temperature Grade Extended industrial (LM2904 A-grade) Industrial Commercial Commercial Industrial (LM2904B grade)
Performance Class Original LM2904 generation Original LM2904 generation Original LM258 generation Original LM358 generation Enhanced (improved offset and drive)
Input Common-Mode Range Extends to ground/VEE Extends to ground/VEE Extends to ground/VEE Extends to ground/VEE Extends to ground/VEE

Ключевые отличия

  • Extended industrial temperature grade in standard DIP-8 (против LM358AN)
  • Onsemi second-source continuity (против LM2904)
  • Original-generation cost vs enhanced performance (против LM2904B)

Заметки по проектированию

Decouple the LM2904AN supply with a 100 nF ceramic capacitor placed within a few millimeters of pin 8 (VCC) and pin 4 (GND/VEE), plus 4.7 uF to 10 uF of bulk capacitance per board. Because the dual amplifiers share one supply pair, fast switching on one channel can couple into the other through supply impedance; the local ceramic capacitor suppresses this cross-talk. Never exceed the 26 V maximum supply in the onsemi part, and observe that in split-supply use each rail pair must still respect the total supply window.

The LM2904 class output stage behaves as a class-AB/class-B stage: it sources current well but sinks weakly near the lower rail, so outputs intended to reach 0V need a pull-down resistor (typically 2k to 10k to ground) to avoid a dead-zone distortion of a few hundred millivolts. Also avoid direct capacitive loads above roughly 100 pF; add a 50 to 200 ohm series resistor between output and cable capacitance to prevent oscillation. Finally, check phase reversal limits: inputs should not be pulled more than a diode drop below VEE.

For through-hole DIP-8 layouts, keep feedback resistor paths short and route the high-impedance inverting-input traces away from output traces of the adjacent amplifier to minimize crosstalk on the shared die. Use a ground plane on the component-side under the part where practical. For single-supply designs, bias input dividers from a well-decoupled node, and consider AC-coupling with a mid-supply virtual ground for audio signals. Estimated: at a gain of 10 with 10k/100k feedback resistors, input-referred noise is dominated by resistor thermal noise above the op-amp's own contribution.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

Compliance status was not stated in the retrieved distributor snippets; confirm RoHS/REACH status on the onsemi product page before ordering for regulated markets.

Данные проверены: 2026-11-08 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

lm2904an datasheet lm2904an datasheet pdf lm2904an pinout lm2904an equivalent lm2904an replacement lm2904an vs lm358an lm2904a 3peak onsemi lm2904an lm2904an price lm2904an stock lm2904 dual op amp 26v 700khz lm2904an application circuit

Связанные компоненты & термины

onsemi ON Semiconductor LM2904AN LM2904 LM2904B LM2904NG LM258AN LM358AN Texas Instruments 3PEAK operational amplifier op-amp dual op-amp single-supply operation gain-bandwidth product common-mode input voltage range 8-PDIP DIP-8 through-hole RoHS industrial signal conditioning active filter transducer amplifier
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ