LM393APWLE - Dual 36V Comparator, 8-TSSOP | Texas Instruments
部品番号: LM393APWLE ✓ 生産中LM393APWLE 概要
A comparator is an analog integrated circuit that evaluates two input voltages and produces a digital logic state indicating which input is higher. Within the power-management IC hierarchy, the LM393 belongs to the comparator family rather than an amplifier or logic gate. Its two channels are independent, allowing one package to implement two sensing functions while sharing the same supply connections.
Key characteristics include two comparator channels, open-collector outputs, a 36 V maximum supply-voltage rating, and a commercial temperature range of 0°C to 70°C. The open-collector outputs require an external pull-up resistor and can be wired for wired-AND behavior. This architecture is useful when an interface must remain compatible with legacy TTL or open-collector logic.
The LM393APWLE is based on the LM393 family of bipolar differential comparators. Each channel compares a non-inverting and an inverting input, while the two output stages provide open-collector sinking capability. Because the output transistor is not actively driven high, output rise time depends on the pull-up resistor, load capacitance, and signal-chain capacitance rather than solely on the comparator output-stage drive strength.
Typical uses include overvoltage and undervoltage detection, sensor-threshold conditioning, zero-crossing detection, industrial control interfaces, and battery-powered monitoring. For lower-voltage systems, the wide supply range also permits operation from conventional industrial rails, subject to the input common-mode and output-circuit restrictions stated in the manufacturer datasheet.
The primary design consideration is the open-collector interface. Select the external pull-up resistor to balance rising time, power, and drive current, and account for leakage from the attached logic family. Ensure that both input voltages remain within the allowable common-mode range and that the pull-up supply does not exceed the output-pin rating.
This product page combines the manufacturer specifications, package and pin information, sourcing guidance, practical application examples, and carefully qualified replacement considerations. It also highlights where B-grade family members can improve performance while retaining pin compatibility, helping engineers make informed design decisions without assuming that every similar comparator is a true drop-in replacement.
ドロップイン代替品: LM393APWLE — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
LM393BPWR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
LM393APWLE 最大定格&電気的特性
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| 出力タイプ | Open-collector |
| Maximum Total Supply Voltage | 36 V |
| Supply Voltage Range | 2 V to 36 V |
| 動作温度範囲 | 0°C to 70°C |
| Supply Current Independence | Independent of supply voltage |
| Channel Independence | Two independent voltage comparators |
| パッケージ | 8-pin TSSOP |
| 実装タイプ | Surface mount |
| Packaging | Tape and reel |
| AEC-Q100 Qualification | Not applicable |
LM393APWLE ピン構成
| ピン 1 | OUT1 — Open-collector output of comparator channel 1 |
| ピン 2 | IN1− — Inverting input of comparator channel 1 |
| ピン 3 | IN1+ — Non-inverting input of comparator channel 1 |
| ピン 4 | GND — Ground connection |
| ピン 5 | IN2+ — Non-inverting input of comparator channel 2 |
| ピン 6 | IN2− — Inverting input of comparator channel 2 |
| ピン 7 | OUT2 — Open-collector output of comparator channel 2 |
| ピン 8 | VCC — Positive supply connection |
主な用途
LM393APWLE の用途: 6 件s: Industrial Overvoltage Detection, Battery Voltage Monitoring, Temperature Sensor Signal Conditioning, Window Limit Detection, Zero-Crossing Detection, Open-Collector Interface Bridging.
Industrial Overvoltage Detection
The LM393APWLE is well suited to industrial overvoltage detection because it contains two independent comparator channels and supports a total supply rating of 36 V. Each channel can compare a divided feedback signal with a reference and control an open-collector fault indication. The external pull-up allows the output to interface directly with a supervisory circuit or PLC input. Because the outputs are open collector, multiple fault signals can also share a common wired-AND node when the voltage, leakage, and logic thresholds remain compatible.
おすすめ
Battery Voltage Monitoring
The LM393APWLE can monitor a battery pack by comparing divided cell or pack voltage against a reference at each channel. Its two independent comparators permit separate upper- and lower-threshold detection without requiring two packages. The open-collector outputs can pull down an indicator or wakeup line, with pull-up resistors setting the inactive logic level. Designers should verify the input common-mode range across the full battery range and account for reference tolerance, divider error, and comparator offset at the selected operating temperature.
おすすめ
Temperature Sensor Signal Conditioning
The LM393APWLE can compare the output of a temperature sensor with a setpoint and produce a digital overtemperature or undertemperature signal. Its differential inputs allow the sensor signal to be compared directly with a reference or resistor-divider threshold. Two channels can serve a heating system, where one signal indicates high temperature and another indicates low temperature. The output pull-up should be selected for the connected controller, while sensor slew, hysteresis, and noise near the threshold must be evaluated to prevent output chatter.
おすすめ
Window Limit Detection
The two independent channels in the LM393APWLE are useful for implementing upper and lower limits around an analog signal. Each comparator can evaluate a scaled measurement against a reference, producing separate open-collector outputs for conditions outside the acceptable window. This arrangement is common in power supplies, battery packs, and industrial controls. Because the LM393's output transition occurs at a threshold, hysteresis resistors or positive feedback should be added where chatter would be unacceptable.
おすすめ
Zero-Crossing Detection
The LM393APWLE can detect the crossing of an analog waveform by comparing the signal with a reference derived from the same waveform. The comparator output then changes state around the crossing, making the device useful in oscillator, phase-control, and signal-presence circuits. The differential inputs permit reference and signal to be applied in either polarity. Keep the compared nodes within the common-mode range, provide a defined pull-up voltage, and use local decoupling to prevent supply noise from shifting the switching point.
おすすめ
Open-Collector Interface Bridging
The LM393APWLE bridges open-collector domains by converting a differential voltage decision into a pulled-down logic output. This is useful when a sensor, photocoupler, or legacy peripheral provides an analog or floating signal and the destination expects a digital alarm or interrupt. The two channels can support complementary or independent indications. Pull-up selection must preserve the destination device's high-level voltage and input-current limits, while the common ground connection and input-referenced signals must remain within the comparator's permitted operating conditions.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM393APWLE — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM393BPWR |
|---|---|---|
| Package | 8-pin TSSOP | 8-pin TSSOP |
| Brand | Texas Instruments | Texas Instruments |
| Comparator Channels | 2 independent channels | 2 independent channels |
| Output Type | Open-collector | Open-collector |
| Maximum Total Supply Voltage | 36 V | 36 V |
主な差別化要因
- Two independent channels in one TSSOP-8 package (vs LM393BPWR)
- Legacy-compatible open-collector interface (vs LM393BPWR)
- B-generation option for newer designs (vs LM393BPWR)
設計ノート
Do not treat an open-collector output as actively driven high. Each LM393APWLE output requires an external pull-up resistor, and the resistor voltage must remain within the output-pin limits. Check the attached device's input-leakage current, output capacitance, and required logic-high voltage. If two open-collector outputs share a node, verify that the aggregate sink current stays within the comparator's output-current rating and that the pull-up produces a valid high level in the worst case.
Place the supply bypass capacitor close to pin 8 and connect pin 4 to a low-impedance ground plane using the shortest practical return path. Long input traces can pick up noise because the comparator may switch rapidly when its inputs cross. Keep sensitive threshold nodes compact, keep the pull-up resistor near the output, and separate the comparator's supply and ground pins from high-current switching-return paths. These layout practices reduce false threshold transitions in noisy industrial systems.
Add hysteresis wherever the compared signals can cross the threshold slowly or where noise could cause repeated output transitions. Positive feedback from each output to its non-inverting input is a common technique, but it changes the effective switching threshold and must be checked for both logic states. For RC-based sensors, calculate the allowable input slewing rate at the switching point and ensure that the application does not exceed the comparator's response capability.
Ensure that the pull-up supply, comparator supply, and attached input signals satisfy their respective absolute-maximum and common-mode limits. The family supports a 36 V maximum total supply rating, but that is not permission to apply 36 V to every output or input pin. Review the manufacturer datasheet for input voltage behavior under supply-off conditions before using the LM393APWLE in systems where a downstream device can back-power an output.
コンプライアンス情報
The LM393APWLE is a commercial-grade comparator rather than an automotive-qualified device. Exact environmental declarations must be confirmed through the current TI product page and supporting compliance documents.