Texas Instruments

LM393APWLE - Dual 36V Comparator, 8-TSSOP | Texas Instruments

MPN: LM393APWLE ✓ Aktif
36 V Vdss Independent of supply voltage Id 8-pin TSSOP Package
MOQ: 1 |

LM393APWLE Ringkasan

The Texas Instruments LM393APWLE is a dual differential comparator with two independent open-collector outputs, a 36 V maximum total supply rating, and an 8-pin TSSOP package. It is a commercial-grade device intended for operation from a single supply or suitable dual-supply arrangement, making it appropriate for threshold detection, window comparison, and general-purpose signal conditioning.

A comparator is an analog integrated circuit that evaluates two input voltages and produces a digital logic state indicating which input is higher. Within the power-management IC hierarchy, the LM393 belongs to the comparator family rather than an amplifier or logic gate. Its two channels are independent, allowing one package to implement two sensing functions while sharing the same supply connections.

Key characteristics include two comparator channels, open-collector outputs, a 36 V maximum supply-voltage rating, and a commercial temperature range of 0°C to 70°C. The open-collector outputs require an external pull-up resistor and can be wired for wired-AND behavior. This architecture is useful when an interface must remain compatible with legacy TTL or open-collector logic.

The LM393APWLE is based on the LM393 family of bipolar differential comparators. Each channel compares a non-inverting and an inverting input, while the two output stages provide open-collector sinking capability. Because the output transistor is not actively driven high, output rise time depends on the pull-up resistor, load capacitance, and signal-chain capacitance rather than solely on the comparator output-stage drive strength.

Typical uses include overvoltage and undervoltage detection, sensor-threshold conditioning, zero-crossing detection, industrial control interfaces, and battery-powered monitoring. For lower-voltage systems, the wide supply range also permits operation from conventional industrial rails, subject to the input common-mode and output-circuit restrictions stated in the manufacturer datasheet.

The primary design consideration is the open-collector interface. Select the external pull-up resistor to balance rising time, power, and drive current, and account for leakage from the attached logic family. Ensure that both input voltages remain within the allowable common-mode range and that the pull-up supply does not exceed the output-pin rating.

This product page combines the manufacturer specifications, package and pin information, sourcing guidance, practical application examples, and carefully qualified replacement considerations. It also highlights where B-grade family members can improve performance while retaining pin compatibility, helping engineers make informed design decisions without assuming that every similar comparator is a true drop-in replacement.

Pilihan pengganti yang segera untuk LM393APWLE — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

LM393BPWR

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 8-pin TSSOP
Retains the same two-channel TSSOP-8 open-collector architecture and 36 V maximum total supply rating, while using the B generation with improved offset-voltage and response-time performance; exact improvement values are .

📋 Alternatif rujukan (tidak dalam katalog)

LM393APWLE Penilaian maksimum & Ciri-ciri Elektrik

Comparator Type Dual differential comparator
Number of Channels 2 channels
Jenis Output Open-collector
Maximum Total Supply Voltage 36 V
Supply Voltage Range 2 V to 36 V
Gambaran Suhu Operasi 0°C to 70°C
Supply Current Independence Independent of supply voltage
Channel Independence Two independent voltage comparators
Kemasan 8-pin TSSOP
Jenis Pemasangan Surface mount
Packaging Tape and reel
AEC-Q100 Qualification Not applicable

Konfigurasi Pin LM393APWLE

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
Pin 1 OUT1 — Open-collector output of comparator channel 1
Pin 2 IN1− — Inverting input of comparator channel 1
Pin 3 IN1+ — Non-inverting input of comparator channel 1
Pin 4 GND — Ground connection
Pin 5 IN2+ — Non-inverting input of comparator channel 2
Pin 6 IN2− — Inverting input of comparator channel 2
Pin 7 OUT2 — Open-collector output of comparator channel 2
Pin 8 VCC — Positive supply connection

Aplikasi Biasa

LM393APWLE patut untuk 6 aplikasis: Industrial Overvoltage Detection, Battery Voltage Monitoring, Temperature Sensor Signal Conditioning, Window Limit Detection, Zero-Crossing Detection, Open-Collector Interface Bridging.

🏭

Industrial Overvoltage Detection

The LM393APWLE is well suited to industrial overvoltage detection because it contains two independent comparator channels and supports a total supply rating of 36 V. Each channel can compare a divided feedback signal with a reference and control an open-collector fault indication. The external pull-up allows the output to interface directly with a supervisory circuit or PLC input. Because the outputs are open collector, multiple fault signals can also share a common wired-AND node when the voltage, leakage, and logic thresholds remain compatible.

⚡

Battery Voltage Monitoring

The LM393APWLE can monitor a battery pack by comparing divided cell or pack voltage against a reference at each channel. Its two independent comparators permit separate upper- and lower-threshold detection without requiring two packages. The open-collector outputs can pull down an indicator or wakeup line, with pull-up resistors setting the inactive logic level. Designers should verify the input common-mode range across the full battery range and account for reference tolerance, divider error, and comparator offset at the selected operating temperature.

🏭

Temperature Sensor Signal Conditioning

The LM393APWLE can compare the output of a temperature sensor with a setpoint and produce a digital overtemperature or undertemperature signal. Its differential inputs allow the sensor signal to be compared directly with a reference or resistor-divider threshold. Two channels can serve a heating system, where one signal indicates high temperature and another indicates low temperature. The output pull-up should be selected for the connected controller, while sensor slew, hysteresis, and noise near the threshold must be evaluated to prevent output chatter.

🔧

Window Limit Detection

The two independent channels in the LM393APWLE are useful for implementing upper and lower limits around an analog signal. Each comparator can evaluate a scaled measurement against a reference, producing separate open-collector outputs for conditions outside the acceptable window. This arrangement is common in power supplies, battery packs, and industrial controls. Because the LM393's output transition occurs at a threshold, hysteresis resistors or positive feedback should be added where chatter would be unacceptable.

〰️

Zero-Crossing Detection

The LM393APWLE can detect the crossing of an analog waveform by comparing the signal with a reference derived from the same waveform. The comparator output then changes state around the crossing, making the device useful in oscillator, phase-control, and signal-presence circuits. The differential inputs permit reference and signal to be applied in either polarity. Keep the compared nodes within the common-mode range, provide a defined pull-up voltage, and use local decoupling to prevent supply noise from shifting the switching point.

🖥️

Open-Collector Interface Bridging

The LM393APWLE bridges open-collector domains by converting a differential voltage decision into a pulled-down logic output. This is useful when a sensor, photocoupler, or legacy peripheral provides an analog or floating signal and the destination expects a digital alarm or interrupt. The two channels can support complementary or independent indications. Pull-up selection must preserve the destination device's high-level voltage and input-current limits, while the common ground connection and input-referenced signals must remain within the comparator's permitted operating conditions.

Ringkasan Produk Disebarkan

LM393APWLE Texas Instruments Dipergunakan di: Industrial Overvoltage Detection, Battery Voltage Monitoring, Temperature Sensor Signal Conditioning, Window Limit Detection, Zero-Crossing Detection, Open-Collector Interface Bridging LM393BPWR Pin-compatible B-generation comparator Dipergunakan di: Industrial Overvoltage Detection, Battery Voltage Monitoring, Temperature Sensor Signal Conditioning, Window Limit Detection, Zero-Crossing Detection, Open-Collector Interface Bridging
What is LM393APWLE?
The LM393APWLE is a Texas Instruments dual differential comparator with two independent channels and open-collector outputs in an 8-pin TSSOP package. According to the TI LM393 product page, each channel compares an inverting input with a non-inverting input, while both channels share supply and ground pins. The device is intended for general-purpose threshold detection, signal conditioning, and industrial control applications within a 0°C to 70°C commercial temperature range.
What is the supply voltage range of LM393APWLE?
The LM393APWLE supports operation from 2 V to 36 V across the applicable supply arrangement. According to the TI LM393 product page, the family can operate from a single power supply or from dual supplies when the total voltage and input common-mode conditions remain within their permitted limits. The 36 V maximum total rating provides ample headroom for industrial 24 V systems, although the attached pull-up network and protected circuitry must also respect the output-pin voltage limit.
Why does the LM393APWLE need a pull-up resistor?
The LM393APWLE uses open-collector outputs, so an external pull-up resistor is required to establish a high output voltage. According to the TI LM393 application guidance, the open-collector transistor actively pulls the output toward ground but does not actively drive it high. The resistor value determines the output rise time, steady-state power, and ability to source sufficient current into the next logic device or cable.
Where can I download the LM393APWLE datasheet PDF?
The official LM393APWLE datasheet can be downloaded from the Texas Instruments LM393 product page or through the TI document link on this page. The manufacturer datasheet contains the ordering information, electrical characteristics, comparator architecture, pin configuration, and application guidance. TI also publishes the PDF Application Design Guidelines for the LM339 and LM393 family, which is useful for understanding open-collector outputs, input behavior, and system-level implementation.
Where is the LM393APWLE pinout located?
The LM393APWLE pinout is shown in the manufacturer datasheet and repeated on this product page for the 8-pin TSSOP configuration. Pin 1 is OUT1, pins 2 and 3 are IN1− and IN1+, pin 4 is GND, pins 5 and 6 are IN2+ and IN2−, pin 7 is OUT2, and pin 8 is VCC. Use the pin-description table in the TI datasheet when assigning PCB tracks and pull-up networks.
What is the LM393APWLE pinout in TSSOP-8?
The LM393APWLE TSSOP-8 pinout is 1 OUT1, 2 IN1−, 3 IN1+, 4 GND, 5 IN2+, 6 IN2−, 7 OUT2, and 8 VCC. According to the TI LM393 datasheet, each channel has one inverting input, one non-inverting input, and one open-collector output. The two comparator channels are electrically independent apart from their shared power connections, allowing both to be used simultaneously.
Can LM393BPWR replace LM393APWLE?
The LM393BPWR can serve as a drop-in replacement for the LM393APWLE when its TSSOP-8 pinout and electrical operating limits satisfy the design. According to the TI LM393 ordering information, LM393B devices can replace LM293, LM393, and LM2903 devices for A and V grades. The B generation provides improved comparator performance, but the manufacturer datasheet should be checked for offset, response-time, and operating-limit requirements before approval.
What can replace LM393APWLE in a drop-in design?
The closest same-footprint replacement is the LM393BPWR, a Texas Instruments B-grade member of the LM393 family offered in TSSOP-8. The TI product documentation identifies LM393B as a replacement for LM393 A and V grades. Because open-collector behavior and package pinout are retained, PCB changes are generally unnecessary, but engineers should verify input common-mode range, output leakage, timing, and production-temperature requirements.
Is LM393APWLE suitable for industrial sensor threshold detection?
The LM393APWLE is suitable for many industrial sensor-threshold detection circuits because it combines two independent comparator channels, open-collector outputs, and a 36 V maximum total supply rating. According to the TI product page, operation from a single supply and dual supplies is supported within the stated voltage limits. The sensor signal must remain within the input common-mode range, and the comparator output needs an appropriate pull-up for the connected digital input.
LM393APWLE vs LM393BPWR - which is better for a new design?
The LM393BPWR is generally preferable for a new design when its improved electrical performance remains compatible with the circuit. The LM393APWLE is the commercial-grade A-version in an 8-pin TSSOP package, while the LM393BPWR is the B-generation counterpart in the same package. According to the TI LM393 product family information, the B generation replaces A and V grades, but timing-sensitive or obsolete designs should still be checked for behavioral changes.
When should I choose LM393APWLE instead of another dual comparator?
Choose the LM393APWLE when the design specifically requires the TI LM393 A-grade electrical behavior, open-collector outputs, dual independent channels, and an 8-pin TSSOP footprint. The LM393BPWR is preferable for new designs when its improved performance is desirable. Choose a CMOS comparator instead when lower supply voltage, lower quiescent current, rail-to-rail input operation, or push-pull output behavior is required rather than legacy open-collector compatibility.
What are the key specifications of LM393APWLE that engineers should know?
The LM393APWLE is a dual differential comparator with two independent channels, open-collector outputs, a 2 V to 36 V operating supply range, a 36 V maximum total supply rating, and a 0°C to 70°C commercial temperature range. According to the TI LM393 product page, it can operate from single or dual supplies when the voltage limits are respected. The device is packaged in an 8-pin TSSOP and requires external pull-up resistors on both outputs.
How do I choose a pull-up resistor for LM393APWLE outputs?
Choose the pull-up resistor by balancing the required output rise time against sink-current and power limits. A smaller resistor produces a faster rising edge and stronger logic-high level but increases current when the open-collector output is low. A larger resistor reduces power and allows more capacitive loading but slows the rising edge and may interact with input leakage. TI's LM393 family application guidance should be used to check the interaction with the attached logic family.
Where can I buy LM393APWLE and check its lead time?
Use the Request a Quote form on this page to ask about LM393APWLE availability, current lead time, minimum order quantity, and shipment quantity. The exact orderable MPN is LM393APWLE, and its E suffix identifies the tape-and-reel ordering option in the TI part-number system. A quotation request is the appropriate route for a precise stock confirmation and a current commercial commitment rather than relying on an obsolete catalog record.
What is the price and stock status of LM393APWLE?
Use the Request a Quote form on this page for the current LM393APWLE price, stock position, and lead time. This page does not publish a static price because component pricing and inventory can change without notice. For engineering evaluation, confirm that the quoted manufacturer part number is exactly LM393APWLE so the 8-pin TSSOP tape-and-reel configuration and electrical grade are not confused with another LM393 ordering code.
Is LM393APWLE compliant with RoHS and REACH?
The LM393APWLE is a commercial-grade Texas Instruments comparator with an 8-pin TSSOP package, but its exact RoHS and REACH declarations should be confirmed from the current manufacturer product page or declaration documents. According to TI's product information, the LM393 family is actively supported and available in multiple package and grade options. Use the declarations linked from the manufacturer product page for formal environmental-compliance qualification.
Does LM393APWLE need a bypass capacitor on the supply pin?
The LM393APWLE supply pin should be decoupled to provide a low-impedance reference and suppress supply disturbances. The amount and placement depend on the circuit's supply impedance, wiring length, and switching noise. Place the bypass capacitor close to pin 8 and provide a short, low-inductance ground return to pin 4. For longer supply traces or noisy industrial environments, add local bulk capacitance and maintain a low-impedance return path.

Data referensi kejuruteraan untuk LM393APWLE — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the LM393APWLE when maintaining the exact LM393 A-grade behavior, 2-to-36 V operating range, dual open-collector channels, and 8-pin TSSOP footprint is required. It is especially suitable for legacy industrial interfaces, threshold detection, and systems that depend on open-collector wired-AND behavior. The LM393BPWR is the closest same-family replacement and should be preferred for a new design when its improved offset and response characteristics are desirable and existing circuitry has been checked for behavioral differences. Avoid a CMOS comparator when the design can change, because lower-voltage rail-to-rail operation and push-pull outputs may change system power, polarity, and interface assumptions. Confirm the input common-mode range, output leakage, pull-up voltage, hysteresis requirements, and production-temperature grade before approving any replacement.

Perbandingan dengan Gantian

Parametr Produk Ini LM393BPWR
Package 8-pin TSSOP 8-pin TSSOP
Brand Texas Instruments Texas Instruments
Comparator Channels 2 independent channels 2 independent channels
Output Type Open-collector Open-collector
Maximum Total Supply Voltage 36 V 36 V

Penyeberangsung Jelas

  • Two independent channels in one TSSOP-8 package (vsLM393BPWR)
  • Legacy-compatible open-collector interface (vsLM393BPWR)
  • B-generation option for newer designs (vsLM393BPWR)

Catatan Desain

Do not treat an open-collector output as actively driven high. Each LM393APWLE output requires an external pull-up resistor, and the resistor voltage must remain within the output-pin limits. Check the attached device's input-leakage current, output capacitance, and required logic-high voltage. If two open-collector outputs share a node, verify that the aggregate sink current stays within the comparator's output-current rating and that the pull-up produces a valid high level in the worst case.

Place the supply bypass capacitor close to pin 8 and connect pin 4 to a low-impedance ground plane using the shortest practical return path. Long input traces can pick up noise because the comparator may switch rapidly when its inputs cross. Keep sensitive threshold nodes compact, keep the pull-up resistor near the output, and separate the comparator's supply and ground pins from high-current switching-return paths. These layout practices reduce false threshold transitions in noisy industrial systems.

Add hysteresis wherever the compared signals can cross the threshold slowly or where noise could cause repeated output transitions. Positive feedback from each output to its non-inverting input is a common technique, but it changes the effective switching threshold and must be checked for both logic states. For RC-based sensors, calculate the allowable input slewing rate at the switching point and ensure that the application does not exceed the comparator's response capability.

Ensure that the pull-up supply, comparator supply, and attached input signals satisfy their respective absolute-maximum and common-mode limits. The family supports a 36 V maximum total supply rating, but that is not permission to apply 36 V to every output or input pin. Review the manufacturer datasheet for input voltage behavior under supply-off conditions before using the LM393APWLE in systems where a downstream device can back-power an output.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The LM393APWLE is a commercial-grade comparator rather than an automotive-qualified device. Exact environmental declarations must be confirmed through the current TI product page and supporting compliance documents.

Data disahkan pada: 2026-11-17 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

LM393APWLE datasheet LM393APWLE pinout LM393APWLE datasheet pdf LM393APWLE equivalent LM393APWLE replacement LM393APWLE cross reference LM393APWLE TSSOP-8 pinout LM393APWLE open collector output LM393APWLE price LM393APWLE stock Texas Instruments LM393APWLE LM393APWLE vs LM393BPWR LM393APWLE application circuit LM393APWLE footprint

Komponen dan Tanda berkaitan

Texas Instruments LM393APWLE LM393BPWR LM393 dual differential comparator comparator analog integrated circuit open-collector output voltage threshold detection TSSOP-8 TSSOP package family surface-mount package industrial control battery monitoring window comparison wired-AND interface supply bypass capacitor input common-mode range input offset voltage response time quiescent current RoHS REACH Texas Instruments LM393 family
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ