LT1037ACP - Low-Noise Precision Op Amp | Texas Instruments
部品番号: LT1037ACP ✓ 生産中LT1037ACP 概要
An operational amplifier is a high-gain, differential-input amplifier used to amplify voltage signals while providing feedback-defined gain, filtering, buffering, and signal conditioning. The LT1037 belongs to the precision operational-amplifier hierarchy, combining low-noise input stages, high open-loop gain, and wide bandwidth. Its applications range from sensor preamplification and laboratory instrumentation to audio and communication signal chains where preserving small signals is important.
The LT1037ACP offers typical input voltage noise density of 2.5 nV/sqrt(Hz) across the wideband noise region and a 1/f noise corner frequency of 2 Hz. Peak-to-peak input noise from 0.1 Hz to 10 Hz is 60 nV, while the maximum equivalent input noise voltage is 3.8 nV/Hz at 1 kHz. These characteristics support low-noise measurement of source impedances where resistor-generated Johnson noise would otherwise dominate the signal chain.
Precision performance comes from a typical 10 uV input offset voltage and maximum 0.2 uV/C input offset drift. The device provides 130 dB common-mode rejection and 130 dB power-supply rejection according to the manufacturer product information. The decompensated LT1037 configuration provides a 60 MHz gain-bandwidth product and is intended for closed-loop gains of 5 or greater, which supports wideband filtering and instrumentation applications where conventional unity-gain-stable compensation is unnecessary.
Typical uses include low-noise sensor preamplifiers, precision bridge amplifiers, high-gain active filters, laboratory measurement equipment, audio preamplifiers, and communication receivers. The 8-pin PDIP package also simplifies prototyping and through-hole assembly. Designers should observe the minimum stable closed-loop gain, provide suitable decoupling, and avoid exceeding the electrical limits identified in the manufacturer datasheet.
Layout should keep the input path short and minimize parasitic capacitance between the input pins and external feedback components. Place input and output bypass capacitors close to the device pins, use a low-noise ground reference, and route sensitive input traces away from high-current switching nodes. Because this is a decompensated amplifier, verify transient stability at the intended closed-loop gain, including tolerance variation of the feedback components.
This product page combines the LT1037ACP electrical characteristics, package information, verified manufacturer documentation, and engineering guidance for selection and layout. It also distinguishes the verified same-package alternative from unsupported cross-package or functional substitutes, helping engineers identify which comparisons are appropriate for an existing 8-pin PDIP design.
ドロップイン代替品: LT1037ACP — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
LT1037CN8#PBF
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LT1037ACP 最大定格&電気的特性
| Amplifier Type | Single-channel precision operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 60 MHz |
| Slew Rate | 11 V/us minimum |
| Typical Open-Loop Gain | 20 V/uV |
| Minimum Open-Loop Gain | 7 V/uV |
| Typical Wideband Input Noise Density | 2.5 nV/sqrt(Hz) |
| Maximum Equivalent Input Noise Voltage | 3.8 nV/Hz at 1 kHz |
| Low-Frequency Noise Corner | 2 Hz |
| Peak-to-Peak Input Noise | 60 nV from 0.1 Hz to 10 Hz |
| Typical Input Offset Voltage | 10 uV |
| Maximum Input Offset Drift | 0.2 uV/C |
| Common-Mode Rejection | 130 dB |
| Power-Supply Rejection | 130 dB |
| Input Bias Current | 55 nA |
| Minimum Stable Closed-Loop Gain | 5 |
| パッケージ | 8-pin PDIP |
| 実装タイプ | Through-hole |
LT1037ACP 8-pin pdip ピン配置ガイド
LT1037ACP (8-pin pdip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: LT1037ACP.
詳細は データシート をご参照ください。
主な用途
LT1037ACP の用途: 6 件s: Precision Sensor Preamplification, Bridge Amplifier Signal Conditioning, Laboratory Instrumentation, High-Gain Active Filtering, Audio Preamplifier, Communication Signal Conditioning.
Precision Sensor Preamplification
The LT1037ACP fits low-level sensor preamplification because its typical input noise density is 2.5 nV/sqrt(Hz), its low-frequency noise corner is 2 Hz, and its typical input offset voltage is 10 uV. Place the amplifier close to the sensor and route the differential input as a short, symmetric pair to limit electromagnetic pickup and parasitic capacitance. Because the LT1037 is decompensated and intended for closed-loop gains of 5 or greater, confirm the required gain against the manufacturer's stability information. Its 130 dB common-mode rejection also helps reject common-mode sensor excitation and ground-related disturbances when those disturbances remain within the device's input and supply limits.
おすすめ
Bridge Amplifier Signal Conditioning
The LT1037ACP is suitable for bridge-amplifier signal conditioning when millivolt-level differential signals must be measured with low offset and high common-mode rejection. Its 10 uV typical offset voltage, 0.2 uV/C maximum offset drift, and 130 dB common-mode rejection reduce errors from imbalance, temperature changes, and common-mode excitation. Use matched resistors and short, guarded input traces to preserve the common-mode advantage. The 60 MHz gain-bandwidth product provides useful bandwidth margin, while the decompensated architecture requires the closed-loop gain to remain at 5 or greater unless the manufacturer identifies another stable configuration.
おすすめ
Laboratory Instrumentation
The LT1037ACP supports laboratory instrumentation that combines low source noise, accurate DC behavior, and wider bandwidth than a general-purpose precision amplifier. The 2.5 nV/sqrt(Hz) typical wideband noise density and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz are useful when amplifying thermocouple, strain-gauge, or laboratory sensor outputs. Its 11 V/us minimum slew rate helps preserve large-signal response in active filters and buffer stages. Place the device away from relay contacts, display drivers, and switching-power circuitry, and use quiet grounding so the measured result is not degraded by PCB leakage or common-mode pickup.
おすすめ
High-Gain Active Filtering
The LT1037ACP is appropriate for high-gain active filters because its 60 MHz gain-bandwidth product and 11 V/us minimum slew rate support wideband closed-loop response. A decompensated implementation can provide higher useful bandwidth than a unity-gain-stable device when the feedback network establishes a gain of 5 or greater. Select resistor and capacitor values against the required noise contribution and verify phase margin with component tolerances. Keep feedback traces short and symmetrically routed, place filter capacitors close to their connected pins, and avoid crossing sensitive nodes with high-current paths to reduce oscillation and unwanted coupling.
おすすめ
Audio Preamplifier
The LT1037ACP can serve in a low-noise audio preamplifier when a wideband, high-gain stage is needed after a low-impedance source. Its 2.5 nV/sqrt(Hz) typical wideband input noise density and 2 Hz 1/f corner can establish a low noise floor for high-resolution audio paths, while its 130 dB power-supply rejection helps isolate the amplifier from supply ripple. The minimum stable gain of 5 must be reflected in the feedback network. For microphone stages, evaluate source impedance, input bias current, grounding, and cable noise together because low amplifier voltage noise alone does not determine the total input-referred noise.
おすすめ
Communication Signal Conditioning
The LT1037ACP fits communication signal-conditioning blocks that require low noise, accurate offset behavior, and sufficient bandwidth. Its 60 MHz gain-bandwidth product, 11 V/us minimum slew rate, and typical 20 V/uV open-loop gain can support receiver amplifiers and IF-stage conditioning around suitable closed-loop gains. The 130 dB common-mode and power-supply rejection ratios reduce coupling from shared supplies and data lines. Keep the input network compact, maintain a quiet analog ground, and place decoupling near the supply pins. Validate the complete receiver path for gain-bandwidth and stability because cascaded stages can accumulate phase margin limitations even when each amplifier meets its individual specifications.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LT1037ACP — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LT1037CN8#PBF |
|---|---|---|
| Brand | Texas Instruments | Analog Devices |
| Package | 8-pin PDIP | 8-pin PDIP - same package format |
| Amplifier Configuration | Single-channel operational amplifier | Single-channel operational amplifier |
| Gain-Bandwidth Product | 60 MHz | 60 MHz |
| Slew Rate | 11 V/us minimum | 11 V/us minimum |
| Typical Wideband Input Noise Density | 2.5 nV/sqrt(Hz) | 2.5 nV/sqrt(Hz) |
| Typical Input Offset Voltage | 10 uV | 10 uV |
| Input Offset Drift | 0.2 uV/C maximum | 0.2 uV/C maximum |
| Common-Mode Rejection | 130 dB | 130 dB |
| Power-Supply Rejection | 130 dB | 130 dB |
| Minimum Stable Closed-Loop Gain | 5 | 5 |
| Mounting Type | Through-hole | Through-hole |
主な差別化要因
- Combines low wideband noise with high bandwidth (vs LT1037CN8#PBF)
- Supports accurate low-level signal conditioning (vs LT1037CN8#PBF)
- Retains the same 8-pin PDIP replacement footprint (vs LT1037CN8#PBF)
設計ノート
The LT1037 is a decompensated operational amplifier intended for closed-loop gains of 5 or greater. Using feedback values that create a lower gain can lead to ringing or instability. Design the noise-gain network for the minimum intended gain, include the gain-bandwidth product when setting bandwidth, and test with realistic source impedances and feedback-component tolerances. Verify the final circuit against the stability and compensation guidance in the manufacturer documentation.
Keep the two input pins and feedback components close to the amplifier to minimize parasitic capacitance and unwanted feedback. Route inputs as a compact, symmetrical pair and keep them away from switching nodes, relay contacts, and high-current return paths. For low-level measurements, use a quiet analog-ground region, minimize connector-to-amplifier distance, and consider guarding where cable or board leakage could approach the input offset and noise levels relevant to the design.
Estimate total input-referred noise from the amplifier, source resistance, and feedback network rather than relying on amplifier voltage noise alone. The LT1037ACP has 2.5 nV/sqrt(Hz) typical wideband input noise density, but source impedance can make resistor noise dominant. Also assess the 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz and the 10 uV typical offset against the smallest signal of interest. Stable feedback design and physical isolation are both necessary for precision measurements.
コンプライアンス情報
Compliance status was not stated in the manufacturer product information or product listings used for this entry.