Texas Instruments

LT1037ACP - Low-Noise Precision Op Amp | Texas Instruments

MPN: LT1037ACP ✓ פעיל
3.8 nV/Hz at 1 kHz Vdss 55 nA Id 8-pin PDIP Package 2 Hz Speed
כמות הזמנה מינימלית: 1 |

LT1037ACP סקירה

The Texas Instruments LT1037ACP is a single-channel, low-noise, high-speed precision operational amplifier with a 60 MHz gain-bandwidth product, 11 V/us minimum slew rate, and typical voltage gain of 20 V/uV. It is supplied in an 8-pin PDIP package for through-hole instrumentation, analog signal-conditioning, and low-level measurement systems. The LT1037ACP combines low input noise with low offset voltage and drift, making it suitable for applications requiring accurate amplification of weak signals.

An operational amplifier is a high-gain, differential-input amplifier used to amplify voltage signals while providing feedback-defined gain, filtering, buffering, and signal conditioning. The LT1037 belongs to the precision operational-amplifier hierarchy, combining low-noise input stages, high open-loop gain, and wide bandwidth. Its applications range from sensor preamplification and laboratory instrumentation to audio and communication signal chains where preserving small signals is important.

The LT1037ACP offers typical input voltage noise density of 2.5 nV/sqrt(Hz) across the wideband noise region and a 1/f noise corner frequency of 2 Hz. Peak-to-peak input noise from 0.1 Hz to 10 Hz is 60 nV, while the maximum equivalent input noise voltage is 3.8 nV/Hz at 1 kHz. These characteristics support low-noise measurement of source impedances where resistor-generated Johnson noise would otherwise dominate the signal chain.

Precision performance comes from a typical 10 uV input offset voltage and maximum 0.2 uV/C input offset drift. The device provides 130 dB common-mode rejection and 130 dB power-supply rejection according to the manufacturer product information. The decompensated LT1037 configuration provides a 60 MHz gain-bandwidth product and is intended for closed-loop gains of 5 or greater, which supports wideband filtering and instrumentation applications where conventional unity-gain-stable compensation is unnecessary.

Typical uses include low-noise sensor preamplifiers, precision bridge amplifiers, high-gain active filters, laboratory measurement equipment, audio preamplifiers, and communication receivers. The 8-pin PDIP package also simplifies prototyping and through-hole assembly. Designers should observe the minimum stable closed-loop gain, provide suitable decoupling, and avoid exceeding the electrical limits identified in the manufacturer datasheet.

Layout should keep the input path short and minimize parasitic capacitance between the input pins and external feedback components. Place input and output bypass capacitors close to the device pins, use a low-noise ground reference, and route sensitive input traces away from high-current switching nodes. Because this is a decompensated amplifier, verify transient stability at the intended closed-loop gain, including tolerance variation of the feedback components.

This product page combines the LT1037ACP electrical characteristics, package information, verified manufacturer documentation, and engineering guidance for selection and layout. It also distinguishes the verified same-package alternative from unsupported cross-package or functional substitutes, helping engineers identify which comparisons are appropriate for an existing 8-pin PDIP design.

חלופות תחליף ישיר עבור LT1037ACP — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

LT1037CN8#PBF

✅ Drop-In
📦 8-pin PDIP
Same 8-pin PDIP format and LT1037A family; ordering suffix differs by 0% in the core LT1037 precision-amplifier ratings, while grade and ordering details must be confirmed

📋 חלופה להתייחסות (לא בקטלוג)

LT1037ACP דירוגים מרביים ומאפיינים חשמליים

Amplifier Type Single-channel precision operational amplifier
Number of Channels 1 channel
Gain-Bandwidth Product 60 MHz
Slew Rate 11 V/us minimum
Typical Open-Loop Gain 20 V/uV
Minimum Open-Loop Gain 7 V/uV
Typical Wideband Input Noise Density 2.5 nV/sqrt(Hz)
Maximum Equivalent Input Noise Voltage 3.8 nV/Hz at 1 kHz
Low-Frequency Noise Corner 2 Hz
Peak-to-Peak Input Noise 60 nV from 0.1 Hz to 10 Hz
Typical Input Offset Voltage 10 uV
Maximum Input Offset Drift 0.2 uV/C
Common-Mode Rejection 130 dB
Power-Supply Rejection 130 dB
Input Bias Current 55 nA
Minimum Stable Closed-Loop Gain 5
מארז 8-pin PDIP
סוג הרכבה Through-hole

מדריך תצורת פינים של LT1037ACP 8-pin pdip

תצורת פינים עבור LT1037ACP (מארזת 8-pin pdip). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.

תרשים פינים של מארזת 8-pin pdip עבור LT1037ACP

אין נתוני פריסת פינים מפורטים עבור LT1037ACP.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

LT1037ACP מתאים עבור 6 יישוםs: Precision Sensor Preamplification, Bridge Amplifier Signal Conditioning, Laboratory Instrumentation, High-Gain Active Filtering, Audio Preamplifier, Communication Signal Conditioning.

🧩

Precision Sensor Preamplification

The LT1037ACP fits low-level sensor preamplification because its typical input noise density is 2.5 nV/sqrt(Hz), its low-frequency noise corner is 2 Hz, and its typical input offset voltage is 10 uV. Place the amplifier close to the sensor and route the differential input as a short, symmetric pair to limit electromagnetic pickup and parasitic capacitance. Because the LT1037 is decompensated and intended for closed-loop gains of 5 or greater, confirm the required gain against the manufacturer's stability information. Its 130 dB common-mode rejection also helps reject common-mode sensor excitation and ground-related disturbances when those disturbances remain within the device's input and supply limits.

🏭

Bridge Amplifier Signal Conditioning

The LT1037ACP is suitable for bridge-amplifier signal conditioning when millivolt-level differential signals must be measured with low offset and high common-mode rejection. Its 10 uV typical offset voltage, 0.2 uV/C maximum offset drift, and 130 dB common-mode rejection reduce errors from imbalance, temperature changes, and common-mode excitation. Use matched resistors and short, guarded input traces to preserve the common-mode advantage. The 60 MHz gain-bandwidth product provides useful bandwidth margin, while the decompensated architecture requires the closed-loop gain to remain at 5 or greater unless the manufacturer identifies another stable configuration.

🔬

Laboratory Instrumentation

The LT1037ACP supports laboratory instrumentation that combines low source noise, accurate DC behavior, and wider bandwidth than a general-purpose precision amplifier. The 2.5 nV/sqrt(Hz) typical wideband noise density and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz are useful when amplifying thermocouple, strain-gauge, or laboratory sensor outputs. Its 11 V/us minimum slew rate helps preserve large-signal response in active filters and buffer stages. Place the device away from relay contacts, display drivers, and switching-power circuitry, and use quiet grounding so the measured result is not degraded by PCB leakage or common-mode pickup.

🌐

High-Gain Active Filtering

The LT1037ACP is appropriate for high-gain active filters because its 60 MHz gain-bandwidth product and 11 V/us minimum slew rate support wideband closed-loop response. A decompensated implementation can provide higher useful bandwidth than a unity-gain-stable device when the feedback network establishes a gain of 5 or greater. Select resistor and capacitor values against the required noise contribution and verify phase margin with component tolerances. Keep feedback traces short and symmetrically routed, place filter capacitors close to their connected pins, and avoid crossing sensitive nodes with high-current paths to reduce oscillation and unwanted coupling.

🎧

Audio Preamplifier

The LT1037ACP can serve in a low-noise audio preamplifier when a wideband, high-gain stage is needed after a low-impedance source. Its 2.5 nV/sqrt(Hz) typical wideband input noise density and 2 Hz 1/f corner can establish a low noise floor for high-resolution audio paths, while its 130 dB power-supply rejection helps isolate the amplifier from supply ripple. The minimum stable gain of 5 must be reflected in the feedback network. For microphone stages, evaluate source impedance, input bias current, grounding, and cable noise together because low amplifier voltage noise alone does not determine the total input-referred noise.

📡

Communication Signal Conditioning

The LT1037ACP fits communication signal-conditioning blocks that require low noise, accurate offset behavior, and sufficient bandwidth. Its 60 MHz gain-bandwidth product, 11 V/us minimum slew rate, and typical 20 V/uV open-loop gain can support receiver amplifiers and IF-stage conditioning around suitable closed-loop gains. The 130 dB common-mode and power-supply rejection ratios reduce coupling from shared supplies and data lines. Keep the input network compact, maintain a quiet analog ground, and place decoupling near the supply pins. Validate the complete receiver path for gain-bandwidth and stability because cascaded stages can accumulate phase margin limitations even when each amplifier meets its individual specifications.

סיכום מוצרים מומלצים

LT1037ACP Texas Instruments בשימוש ב-: Precision Sensor Preamplification, Bridge Amplifier Signal Conditioning, Laboratory Instrumentation, High-Gain Active Filtering, Audio Preamplifier, Communication Signal Conditioning LT1037CN8#PBF Same-family PDIP comparison option בשימוש ב-: Precision Sensor Preamplification, Bridge Amplifier Signal Conditioning, Laboratory Instrumentation, High-Gain Active Filtering, Audio Preamplifier, Communication Signal Conditioning
What is the LT1037ACP?
The LT1037ACP is a single-channel, low-noise, high-speed precision operational amplifier from Texas Instruments in an 8-pin PDIP package. According to the manufacturer product information, it combines a 60 MHz gain-bandwidth product, 11 V/us minimum slew rate, typical 20 V/uV open-loop gain, and 2.5 nV/sqrt(Hz) typical wideband input noise density. It is intended for precision signal conditioning, instrumentation, active filtering, and low-level sensor amplification.
What are the key specifications of LT1037ACP that engineers should know?
The key LT1037ACP specifications are 60 MHz gain-bandwidth product, 11 V/us minimum slew rate, 2.5 nV/sqrt(Hz) typical wideband input noise density, 10 uV typical input offset voltage, and 0.2 uV/C maximum offset drift. The manufacturer also specifies 130 dB common-mode rejection and 130 dB power-supply rejection. Because the LT1037 is decompensated, it is intended for closed-loop gains of 5 or greater.
How much noise does the LT1037ACP have?
The LT1037ACP has a typical wideband input noise density of 2.5 nV/sqrt(Hz), a 1/f corner frequency of 2 Hz, and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz. The manufacturer specifies a maximum equivalent input noise voltage of 3.8 nV/Hz at 1 kHz. These figures make the amplifier appropriate for low-level sensor signals, precision bridge amplifiers, laboratory instruments, and active filters where source and resistor noise are important design limits.
What is the gain-bandwidth product and slew rate of the LT1037ACP?
The LT1037ACP provides a 60 MHz gain-bandwidth product and an 11 V/us minimum slew rate. According to the manufacturer product information, this combination supports wideband small-signal response and rapid output-voltage transitions. Since the LT1037 is decompensated, it is stable for closed-loop gains of 5 or greater; designers should not treat it as a unity-gain-stable amplifier when selecting feedback values.
Where can I download the LT1037ACP datasheet PDF?
The LT1037ACP documentation is available through the Analog Devices LT1037 product page at https://www.analog.com/en/products/lt1037.html, which links to the official LT1037 technical documentation. Use the manufacturer pin-description and electrical-characteristics tables when assigning the 8-pin PDIP connections, selecting supply voltages, and checking noise, offset, common-mode rejection, and stability limits.
Where can I find the LT1037ACP pinout?
The LT1037ACP pinout is found in the pin-description section of the official LT1037 manufacturer documentation at https://www.analog.com/en/products/lt1037.html. The device uses an 8-pin PDIP package. Before assigning PCB tracks, use the datasheet table to verify offset null, compensation, supply, input, output, and exposed electrical functions for the exact ordering code.
Where can I buy LT1037ACP online?
Use the Request a Quote form on this page to request availability, lead time, and commercial terms for the LT1037ACP. The exact Texas Instruments ordering code includes the 8-pin PDIP package suffix, so provide the full MPN when requesting a quote. Current lead time and stock should be confirmed through the form because availability for this older precision amplifier can vary by lot and package.
What is the price of LT1037ACP?
Current commercial terms for the LT1037ACP are available through the Request a Quote form on this page. Quote requests should include the full MPN, required quantity, and preferred shipment destination. The form provides a direct response path for price confirmation, lead-time information, stock status, and package-specific fulfillment without relying on a stale market listing.
What is the lead time for LT1037ACP?
Request the current LT1037ACP lead time through the Request a Quote form on this page. State the required quantity, approved source condition, and shipment location so procurement can confirm the most relevant manufacturing and inventory position. For production planning, also request date codes and traceability information because the package suffix identifies an 8-pin PDIP device.
Is LT1037ACP in stock?
Stock for LT1037ACP should be confirmed through the Request a Quote form on this page. Submit the full ordering code, quantity, and delivery requirements to receive current availability and lead-time information. A distributor listing alone does not guarantee that a specified quantity is immediately available, particularly for older through-hole precision amplifier packages.
LT1037ACP vs LT1037CN8#PBF - which is better for an instrumentation design?
The LT1037CN8#PBF is the closest verified same-package comparison for an LT1037ACP instrumentation design because both use the 8-pin PDIP format and correspond to the same LT1037A precision-amplifier family. The suffix distinction should be checked against temperature grade, production marking, and ordering requirements in the manufacturer documentation. Use LT1037ACP when that is the specified BOM item; evaluate LT1037CN8#PBF only after confirming the required grade and sourcing conditions.
What is the difference between LT1037ACP and LT1037CN8#PBF?
The LT1037ACP and LT1037CN8#PBF are identified in cross-reference results as an 8-pin PDIP comparison within the LT1037 family. Their core precision, low-noise, and high-speed performance is closely related, but ordering suffixes can identify different package, temperature, termination, or marking configurations. According to the manufacturer LT1037 documentation, confirm all grade and pin details before treating LT1037CN8#PBF as a drop-in replacement.
When should I choose LT1037ACP over another low-noise op amp?
Choose the LT1037ACP when the design needs a single-channel, through-hole precision amplifier combining 2.5 nV/sqrt(Hz) typical wideband noise density, 60 MHz gain-bandwidth product, 10 uV typical offset, and a 2 Hz low-frequency noise corner. It is particularly suitable when the intended closed-loop gain is 5 or greater. Choose a unity-gain-stable or newer device instead when minimum-gain compatibility, lower supply voltage, or different package requirements dominate.
Is LT1037ACP suitable for a low-noise sensor amplifier?
The LT1037ACP is suitable for a low-noise sensor amplifier when the signal source, bandwidth, and gain meet its operating limits. Its 2.5 nV/sqrt(Hz) typical wideband noise density, 2 Hz 1/f corner, 10 uV typical offset, and 130 dB common-mode rejection support accurate amplification of weak differential signals. For source impedances where thermal noise dominates, compare total amplifier-and-source noise rather than using input voltage noise alone.
What can replace LT1037ACP?
The verified same-package replacement candidate is the LT1037CN8#PBF, which uses the 8-pin PDIP format and belongs to the same LT1037A family. No cross-brand part is presented as a confirmed drop-in because the available cross-reference material does not establish exact pin compatibility, electrical tolerance, and package equivalence for a specific competitor MPN. Before substitution, verify the pinout, minimum stable gain, supply range, noise, offset, temperature grade, and obsolete-part documentation.
What is the best cross-brand equivalent for LT1037ACP?
No cross-brand equivalent is confirmed as a true drop-in replacement for the LT1037ACP in the available documentation. A defensible replacement must retain the 8-pin PDIP footprint, pin-to-pin behavior, minimum stable closed-loop gain of 5, low input-noise performance, offset limits, and supply requirements. Use the manufacturer cross-reference search or request engineering support for a specific competitor MPN, then compare its datasheet before changing the PCB or qualification documentation.

נתוני עזר הנדסיים עבור LT1037ACP — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the LT1037ACP for precision, low-noise through-hole analog designs that benefit from 60 MHz bandwidth, an 11 V/us minimum slew rate, 2.5 nV/sqrt(Hz) typical wideband noise density, and 130 dB common-mode rejection. It is especially appropriate for bridge amplifiers, sensor preamps, laboratory instrumentation, and high-gain filters whose closed-loop gain is 5 or greater. Consider the LT1037CN8#PBF when its ordering grade, termination, marking, and sourcing conditions meet the product requirements while preserving the 8-pin PDIP layout. Do not substitute a surface-mount or different-package amplifier without redesigning the PCB. If the circuit requires unity-gain stability, operation below 5 V, or a modern low-power footprint, compare another qualified device instead of forcing a footprint-only replacement.

השוואה עם חלופות

פרמטר מוצר זה LT1037CN8#PBF
Brand Texas Instruments Analog Devices
Package 8-pin PDIP 8-pin PDIP - same package format
Amplifier Configuration Single-channel operational amplifier Single-channel operational amplifier
Gain-Bandwidth Product 60 MHz 60 MHz
Slew Rate 11 V/us minimum 11 V/us minimum
Typical Wideband Input Noise Density 2.5 nV/sqrt(Hz) 2.5 nV/sqrt(Hz)
Typical Input Offset Voltage 10 uV 10 uV
Input Offset Drift 0.2 uV/C maximum 0.2 uV/C maximum
Common-Mode Rejection 130 dB 130 dB
Power-Supply Rejection 130 dB 130 dB
Minimum Stable Closed-Loop Gain 5 5
Mounting Type Through-hole Through-hole

מבדילים עיקריים

  • Combines low wideband noise with high bandwidth (לעומתLT1037CN8#PBF)
  • Supports accurate low-level signal conditioning (לעומתLT1037CN8#PBF)
  • Retains the same 8-pin PDIP replacement footprint (לעומתLT1037CN8#PBF)

הערות תכנון

The LT1037 is a decompensated operational amplifier intended for closed-loop gains of 5 or greater. Using feedback values that create a lower gain can lead to ringing or instability. Design the noise-gain network for the minimum intended gain, include the gain-bandwidth product when setting bandwidth, and test with realistic source impedances and feedback-component tolerances. Verify the final circuit against the stability and compensation guidance in the manufacturer documentation.

Keep the two input pins and feedback components close to the amplifier to minimize parasitic capacitance and unwanted feedback. Route inputs as a compact, symmetrical pair and keep them away from switching nodes, relay contacts, and high-current return paths. For low-level measurements, use a quiet analog-ground region, minimize connector-to-amplifier distance, and consider guarding where cable or board leakage could approach the input offset and noise levels relevant to the design.

Estimate total input-referred noise from the amplifier, source resistance, and feedback network rather than relying on amplifier voltage noise alone. The LT1037ACP has 2.5 nV/sqrt(Hz) typical wideband input noise density, but source impedance can make resistor noise dominant. Also assess the 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz and the 10 uV typical offset against the smallest signal of interest. Stable feedback design and physical isolation are both necessary for precision measurements.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

Compliance status was not stated in the manufacturer product information or product listings used for this entry.

הנתונים אומתו בתאריך: 2026-11-09 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

LT1037ACP LT1037ACP datasheet LT1037ACP datasheet pdf LT1037ACP pinout LT1037ACP specifications Texas Instruments LT1037ACP LT1037ACP equivalent LT1037ACP replacement LT1037ACP vs LT1037CN8#PBF LT1037ACP PDIP-8 op amp LT1037ACP noise density LT1037ACP application circuit

רכיבים ומונחים קשורים

Texas Instruments LT1037ACP LT1037CN8#PBF LT1037A operational amplifier precision operational amplifier low-noise amplifier single-channel amplifier signal-conditioning IC analog semiconductor input voltage noise density 1/f noise common-mode rejection ratio CMRR power-supply rejection ratio PSRR gain-bandwidth product slew rate input offset voltage input offset drift decompensated amplifier 8-pin PDIP PDIP package family through-hole mounting surface-mount active filter bridge amplifier sensor preamplifier
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר