LT1495HS8 - 1.5µA Dual Precision Rail-to-Rail Op Amp | ADI
部品番号: LT1495HS8 ✓ 生産中LT1495HS8 概要
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LT1495 belongs to the precision op-amp category, the broader linear-amplifier hierarchy, and ultimately the amplifier IC and analog semiconductor product families. Its rail-to-rail input and output characteristics allow useful signal operation near the supply rails, while its very low supply current supports battery-powered instrumentation and low-power measurement systems.
The principal features of the LT1495HS8 include its dual-channel configuration, maximum supply current of 1.5µA, 375µV maximum input offset voltage, 100pA maximum input offset current, and 100V/mV minimum open-loop gain. The 2.7kHz gain-bandwidth product makes the device suitable for slow precision-control and signal-conditioning loops rather than high-speed waveform processing. Its 0.001V/µs slew rate further supports low-frequency, high-resolution measurement circuits.
The LT1495 combines low-power operation with precision-focused DC performance. Offset voltage and offset drift are important when the amplifier follows a sensor output, while low input offset current reduces bias-related errors at high source impedances. The dual configuration allows two precision amplifier channels in one 8-lead SOIC package, reducing board area when compared with two separate single amplifiers. Because the gain-bandwidth product is limited to 2.7kHz, feedback-network selection should favor stable gains and avoid high closed-loop bandwidth requirements.
Typical applications include low-power sensor conditioning, precision current measurement, battery-operated instrumentation, low-frequency active filters, and slow closed-loop control. In these systems, the LT1495 can amplify small sensor or error-amplifier signals while consuming no more than the family-level 1.5µA maximum supply current. Designers should also consider whether the 2.7kHz bandwidth is sufficient for the required settling time and signal bandwidth.
A key design consideration is to verify the common-mode and output-voltage limits against the intended supply voltage and signal range. Feedback-component values should also be selected to support stable operation at the target closed-loop gain. If a design requires substantially faster settling, higher slew rate, or lower offset than this device provides, an alternative amplifier family may be more appropriate.
This product record combines the manufacturer’s family specifications with package, application, pinout, and drop-in-replacement guidance. It also identifies where procurement, technical comparison, and circuit-implementation decisions require additional engineering review.
ドロップイン代替品: LT1495HS8 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストLT1495HS8 最大定格&電気的特性
| Number of Amplifiers | 2 circuits |
| Amplifier Type | General-purpose precision operational amplifier |
| Maximum Supply Current | 1.5µA per amplifier |
| Input Offset Voltage | 375µV maximum |
| Input Offset Voltage Drift | 0.4µV/°C typical |
| Input Offset Current | 100pA maximum |
| Minimum Open-Loop Gain | 100V/mV |
| Gain-Bandwidth Product | 2.7kHz |
| Slew Rate | 0.001V/µs |
| Input Common-Mode Range | Rail-to-rail input |
| Output Range | Rail-to-rail output |
| パッケージ | 8-SOIC, 0.154 inch / 3.90mm width |
| 実装タイプ | Surface mount |
| Product Page Packaging Option | Tube |
| Lead Finish | Matte tin (Sn) |
| RoHS ステータス | ROHS3Compliant |
LT1495HS8 ピン構成
| ピン 1 | OUT A — Output of amplifier A |
| ピン 2 | −IN A — Inverting input of amplifier A |
| ピン 3 | +IN A — Non-inverting input of amplifier A |
| ピン 4 | V− — Negative supply connection |
| ピン 5 | +IN B — Non-inverting input of amplifier B |
| ピン 6 | −IN B — Inverting input of amplifier B |
| ピン 7 | OUT B — Output of amplifier B |
| ピン 8 | V+ — Positive supply connection |
主な用途
LT1495HS8 の用途: 6 件s: Battery-Powered Sensor Signal Conditioning, Precision Current Measurement, Precision Data-Acquisition Front End, Low-Power Active Filtering, Battery-Operated Instrumentation, Precision Reference Buffering.
Battery-Powered Sensor Signal Conditioning
The LT1495HS8 fits low-energy sensor front ends because the LT1495 family operates with no more than 1.5µA supply current per amplifier while providing rail-to-rail input and output operation. Both channels can condition a differential sensor output and buffer a reference or auxiliary signal. The 375µV maximum input offset voltage and 100pA maximum input offset current help control DC error, although the 2.7kHz gain-bandwidth product limits the design to signals whose bandwidth and settling requirements remain compatible with that value.
おすすめ
Precision Current Measurement
The LT1495HS8 can amplify the small voltage generated by a current shunt or current-sense transducer in a precision measurement system. Its input offset current is specified at no more than 100pA, helping limit bias error at high source impedance, while the minimum open-loop gain of 100V/mV supports accurate closed-loop operation. The dual package can provide one sensing amplifier and one reference or output buffer. With a 2.7kHz gain-bandwidth product and 0.001V/µs slew rate, the circuit is best suited to relatively slow measurements rather than high-frequency transients.
おすすめ
Precision Data-Acquisition Front End
The LT1495HS8 is useful as a low-power differential input stage ahead of a high-resolution converter in a portable data-acquisition system. Rail-to-rail input operation permits operation near the available supply range, and the 375µV maximum offset voltage helps preserve the integrity of small sensor-derived signals. Two channels can condition differential inputs or buffer a common reference. Because bandwidth is limited to 2.7kHz, the application should avoid demanding rapid settling or wide-bandwidth noise performance beyond the amplifier’s operating range.
おすすめ
Low-Power Active Filtering
The LT1495HS8 can implement first-order or modest-bandwidth active filters in low-frequency measurement systems. Its maximum supply current of 1.5µA per amplifier reduces the contribution of the active stage to total system power, while the 2.7kHz gain-bandwidth product gives designers a concrete upper reference for usable closed-loop bandwidth. The rail-to-rail output characteristic can improve dynamic range in low-voltage systems. Filter Q and frequency should be selected conservatively so that phase margin and settling behavior remain acceptable at the highest intended operating frequency.
おすすめ
Battery-Operated Instrumentation
The LT1495HS8 supports portable instrumentation that must balance measurement accuracy against energy use. A 1.5µA maximum supply current per amplifier is central to this fit, while 375µV maximum input offset voltage, 0.4µV/°C typical drift, and 100pA maximum input offset current support precision DC measurements. The dual 8-SOIC configuration integrates two channels without requiring two separate packages. Engineers should verify supply range and common-mode limits in the final circuit and avoid applications requiring bandwidth beyond the 2.7kHz gain-bandwidth product.
おすすめ
Precision Reference Buffering
The LT1495HS8 can buffer a low-current reference or provide gain in a precision reference-control loop where the ultra-low 1.5µA supply-current limit is valuable. The minimum open-loop gain of 100V/mV helps reduce closed-loop gain error, and rail-to-rail output operation supports wider usable output range in low-voltage systems. One channel may buffer the reference while the other provides error amplification or an output stage. Care is required because the 2.7kHz bandwidth and 0.001V/µs slew rate limit transient response and reference settling speed.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LT1495HS8 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Package | 8-SOIC, 0.154 inch / 3.90mm width |
| Brand | Analog Devices |
| Number of Amplifiers | 2 circuits |
| Amplifier Type | General-purpose precision operational amplifier |
| Maximum Supply Current | 1.5µA per amplifier |
| Input Offset Voltage | 375µV maximum |
| Input Offset Voltage Drift | 0.4µV/°C typical |
| Input Offset Current | 100pA maximum |
| Minimum Open-Loop Gain | 100V/mV |
| Gain-Bandwidth Product | 2.7kHz |
| Slew Rate | 0.001V/µs |
| Input and Output Range | Rail-to-rail input and output |
主な差別化要因
- Ultra-low supply current with dual precision channels (vs General-purpose dual rail-to-rail op amps)
- Input offset voltage suitable for precision DC conditioning (vs Higher-bandwidth general-purpose dual op amps)
- Very low input bias current (vs CMOS input dual amplifier families with higher bias-current floors)
設計ノート
Do not treat the 1.5µA family specification as sufficient to guarantee usable signal bandwidth. The 2.7kHz gain-bandwidth product and 0.001V/µs slew rate make the LT1495HS8 appropriate for slow precision loops, not wide-band signal chains. Check the required settling interval, closed-loop gain, output amplitude, and load before committing to the amplifier. A request for higher speed should trigger selection of a faster amplifier family rather than compensation or oversizing of the LT1495 circuit.
Use the official 8-SOIC pin drawing and preserve the package pin-1 orientation when laying out the PCB. Place each amplifier’s input-network connections close to pins 2, 3, 5, and 6, keep output routing away from sensitive input traces, and connect the supply pins to short, low-impedance paths. Although the circuit consumes little power, long supply traces and poor grounding can degrade measured accuracy by adding series resistance and coupling external noise into the high-impedance signal path.
Calculate bias-current error from the specified 100pA maximum input offset current and the effective source impedance at each input. This is especially important for high-impedance sensors because even a small current can create a meaningful error voltage. Resistor values in the feedback network should remain high enough to preserve low input bias current benefits while remaining low enough to avoid excessive thermal noise and leakage susceptibility. Keep the two amplifier channels physically separated from switching nodes and noisy digital return paths.
コンプライアンス情報
The LT1495HS8#PBF ordering form is identified as ROHS3Compliant and uses a matte-tin lead finish. REACH, halogen-free, and conflict-minerals status are not stated.