LT1810IS8 - Dual 180MHz R-R Op Amp | Analog Devices
部品番号: LT1810IS8 ✓ 生産中LT1810IS8 概要
An operational amplifier is an analog semiconductor that amplifies the voltage difference between its differential inputs. The LT1810 belongs to the operational-amplifier hierarchy, where it provides closed-loop gain, buffering, filtering, level shifting, and signal conditioning. Rail-to-rail input and output operation allows useful signal processing close to the supply rails, while the dual configuration places two amplifiers in one package.
Key features include a 180 MHz gain-bandwidth product at gains of 10 or higher, a 320 MHz −3 dB small-signal bandwidth at unity gain, and a 350 V/µs slew rate. The output stage can source or sink 85 mA, providing useful drive for low-voltage signal chains. Low-distortion operation and the broad bandwidth make the LT1810 suitable for pulse, data-conversion, video, and general high-speed conditioning applications.
The dual LT1810 uses the standard dual-operational-amplifier pin arrangement in its 8-pin SO package. Its rail-to-rail input range includes both supply rails, and its output capability extends toward the rails as load and supply conditions permit. These characteristics reduce the need for input or output range reduction in systems operating from low-voltage rails.
Typical uses include photodiode signal conditioning, waveform and pulse amplification, video interfaces, low-voltage data-acquisition front ends, active filtering, and general-purpose high-speed analog signal processing. In these applications, the 180 MHz bandwidth supports wide-frequency signals, while the 350 V/µs slew rate improves response to fast edges.
When laying out the circuit, use short, low-impedance connections for feedback and input networks, and place compensation and decoupling components close to the relevant pins. Maintain adequate output-load and supply-decoupling conditions for the intended operating voltage. Because the device is optimized for speed rather than micropower consumption, verify that system power and thermal budgets remain acceptable.
This page combines manufacturer performance data with package, application, replacement, and design guidance. The alternative list is limited to pin-compatible family members because no independently verified cross-manufacturer drop-in equivalents were established for the LT1810IS8.
ドロップイン代替品: LT1810IS8 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
LT1810IS8#PBF
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LT1810CS8#PBF
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LT1810IS8#TRPBF
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LT1810IS8 最大定格&電気的特性
| Number of Amplifiers | 2 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Gain-Bandwidth Product | 180 MHz at gain ≥ 10 |
| Unity-Gain Bandwidth | 320 MHz −3 dB |
| Slew Rate | 350 V/µs |
| Output Current | 85 mA |
| Input Range | Rail-to-rail, including both supply rails |
| Output Range | Rail-to-rail |
| Minimum Operating Temperature | −40 °C |
| Maximum Operating Temperature | +85 °C |
| パッケージ | 8-pin SOIC, 3.90 mm body width |
| 実装タイプ | Surface mount |
| Lead-Free Status | Available as LT1810IS8#PBF |
LT1810IS8 ピン構成
| ピン 1 | OUTA — Amplifier A output |
| ピン 2 | INTA- — Inverting input for amplifier A |
| ピン 3 | INTA+ — Non-inverting input for amplifier A |
| ピン 4 | V- — Negative supply connection |
| ピン 5 | INTB+ — Non-inverting input for amplifier B |
| ピン 6 | INTB- — Inverting input for amplifier B |
| ピン 7 | OUTB — Amplifier B output |
| ピン 8 | V+ — Positive supply connection |
主な用途
LT1810IS8 の用途: 6 件s: Photodiode Signal Conditioning, Video Interface Amplification, Pulse and Edge Signal Conditioning, Low-Voltage Data Acquisition, Active Filtering, Industrial Signal Conditioning.
Photodiode Signal Conditioning
The LT1810IS8 is well suited to high-speed photodiode preamplification because its 320 MHz −3 dB unity-gain bandwidth supports wideband optical-signal conditioning and its 350 V/µs slew rate preserves fast transition edges. The dual SOIC package also allows a transimpedance stage and a follow-up gain or filtering stage to share one board area. Designers should account for photodiode capacitance, bias-resistor noise, and feedback stability when setting the closed-loop response.
おすすめ
Video Interface Amplification
The LT1810IS8 can amplify or buffer low-voltage video signals when broad bandwidth and fast settling behavior matter. Its 180 MHz gain-bandwidth product at gains of 10 or higher and 320 MHz unity-gain bandwidth provide ample margin for common video-conditioning stages, while rail-to-rail input and output operation supports low-voltage systems. PCB implementation should minimize trace length around the amplifier and preserve the impedance environment needed for stable high-speed feedback.
おすすめ
Pulse and Edge Signal Conditioning
For pulse instrumentation, edge-triggered sensing, and fast control signals, the LT1810IS8 combines a 350 V/µs slew rate with an 85 mA output-current capability. These specifications help the dual amplifier reproduce rapidly changing waveforms without the severe large-signal distortion associated with slower amplifiers. Use short feedback paths and appropriate output loading, and confirm that downstream protection networks do not add excessive capacitance that could disturb stability.
おすすめ
Low-Voltage Data Acquisition
The LT1810IS8 is appropriate for front-end amplification ahead of high-speed converters when the sensor or source operates from a low-voltage rail. Rail-to-rail inputs improve usable signal range, while the 180 MHz closed-loop capability supports wideband data paths. The dual configuration can provide gain in one channel and buffering, level translation, or active filtering in the other. Compensation, sampling, and converter-impedance requirements should be evaluated together to avoid loading errors.
おすすめ
Active Filtering
The LT1810IS8 can implement wideband active filters and fast closed-loop signal-conditioning blocks because its high gain-bandwidth product and slew rate reduce the bandwidth and edge-rate limitations encountered in lower-speed amplifiers. The 8-pin SO package simplifies conventional dual-op-amp filter layouts. Component tolerances, op-amp noise, parasitic capacitance, and the required Q factor should be calculated before finalizing values, particularly for filters with high gain or narrow transition bands.
おすすめ
Industrial Signal Conditioning
The LT1810IS8 industrial-temperature version supports signal conditioning in equipment where the −40 °C to +85 °C range and high-speed response are required. Rail-to-rail operation is valuable in low-voltage industrial controls, while the dual amplifier can reduce component count in multichannel designs. PCB creepage, grounding, noise isolation, and thermal performance should be assessed at the enclosure level, and the LT1810CS8#PBF alternative should be avoided where temperatures fall outside its 0 °C to +70 °C rating.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LT1810IS8 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LT1810IS8#PBF | LT1810CS8#PBF | LT1810IS8#TRPBF |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Number of Amplifiers | 2 | 2 | 2 | 2 |
| Gain-Bandwidth Product | 180 MHz at gain ≥ 10 | 180 MHz at gain ≥ 10 | 180 MHz at gain ≥ 10 | 180 MHz at gain ≥ 10 |
| Unity-Gain Bandwidth | 320 MHz −3 dB | 320 MHz −3 dB | 320 MHz −3 dB | 320 MHz −3 dB |
| Slew Rate | 350 V/µs | 350 V/µs | 350 V/µs | 350 V/µs |
| Output Current | 85 mA | 85 mA | 85 mA | 85 mA |
| Operating Temperature | −40 °C to +85 °C | −40 °C to +85 °C | 0 °C to +70 °C | −40 °C to +85 °C |
| Lead-Free Ordering | Base IS8 designation | #PBF lead-free designation | #PBF lead-free designation | #TRPBF tape-and-reel designation |
主な差別化要因
- Higher speed than the closely related LT1809 (vs LT1809IS8#PBF)
- Broader temperature coverage than the commercial-grade suffix (vs LT1810CS8#PBF)
- Matching core performance with a lead-free ordering designation (vs LT1810IS8#PBF)
設計ノート
Place input, feedback, and compensation components directly beside their associated LT1810IS8 pins. High-speed feedback loops can pick up parasitic inductance and capacitance when connections are long, so use short traces, a continuous ground reference, and minimal loop area. Place supply-decoupling capacitance at the device rather than at the output of a remote regulator or cable.
Treat every LT1810IS8 output as a high-speed node. Avoid long unterminated PCB traces, provide a low-impedance return path, and match controlled-impedance interconnects when driving cables or downstream devices. The 350 V/µs slew rate can expose edge-rate problems that are invisible at low test frequencies, so evaluate the complete source-to-load path rather than only the amplifier in isolation.
Do not substitute the LT1809 family into a design that depends on LT1810 speed: its 100 MHz gain-bandwidth product and 200 V/µs slew rate are lower. Likewise, LT1810CS8#PBF is restricted to 0 °C through +70 °C. Confirm package suffix, temperature grade, pinout, and feedback compensation together; matching only the eight-pin outline does not establish drop-in suitability.
コンプライアンス情報
The LT1810IS8#PBF ordering designation identifies a lead-free option. No explicit RoHS, REACH, halogen-free, conflict-minerals, or automotive-qualification statement was established.