Analog Devices

LT1810IS8 - Dual 180MHz R-R Op Amp | Analog Devices

MPN: LT1810IS8 ✓ Hoạt động
85 mA Id 8-pin SOIC, 3.90 mm body width Package
MOQ: 1 |

LT1810IS8 Tóm tắt

The Analog Devices LT1810IS8 is a dual, low-distortion, rail-to-rail input and output operational amplifier with a 180 MHz gain-bandwidth product, 320 MHz unity-gain bandwidth, and 350 V/µs slew rate. The device is packaged in an 8-pin SOIC and is intended for low-voltage, high-performance signal-conditioning systems requiring fast transient response and flexible input/output voltage ranges.

An operational amplifier is an analog semiconductor that amplifies the voltage difference between its differential inputs. The LT1810 belongs to the operational-amplifier hierarchy, where it provides closed-loop gain, buffering, filtering, level shifting, and signal conditioning. Rail-to-rail input and output operation allows useful signal processing close to the supply rails, while the dual configuration places two amplifiers in one package.

Key features include a 180 MHz gain-bandwidth product at gains of 10 or higher, a 320 MHz −3 dB small-signal bandwidth at unity gain, and a 350 V/µs slew rate. The output stage can source or sink 85 mA, providing useful drive for low-voltage signal chains. Low-distortion operation and the broad bandwidth make the LT1810 suitable for pulse, data-conversion, video, and general high-speed conditioning applications.

The dual LT1810 uses the standard dual-operational-amplifier pin arrangement in its 8-pin SO package. Its rail-to-rail input range includes both supply rails, and its output capability extends toward the rails as load and supply conditions permit. These characteristics reduce the need for input or output range reduction in systems operating from low-voltage rails.

Typical uses include photodiode signal conditioning, waveform and pulse amplification, video interfaces, low-voltage data-acquisition front ends, active filtering, and general-purpose high-speed analog signal processing. In these applications, the 180 MHz bandwidth supports wide-frequency signals, while the 350 V/µs slew rate improves response to fast edges.

When laying out the circuit, use short, low-impedance connections for feedback and input networks, and place compensation and decoupling components close to the relevant pins. Maintain adequate output-load and supply-decoupling conditions for the intended operating voltage. Because the device is optimized for speed rather than micropower consumption, verify that system power and thermal budgets remain acceptable.

This page combines manufacturer performance data with package, application, replacement, and design guidance. The alternative list is limited to pin-compatible family members because no independently verified cross-manufacturer drop-in equivalents were established for the LT1810IS8.

Bộ thay thế dễ dàng lắp đặt cho LT1810IS8 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

LT1810IS8#PBF

✅ Drop-In
📦 8-pin SOIC
Same 180 MHz gain-bandwidth product, 320 MHz unity-gain bandwidth, and 350 V/µs slew rate; ordering code adds lead-free processing information

📋 Tham chiếu thay thế (không có trong danh mục)

LT1810CS8#PBF

✅ Drop-In
📦 8-pin SOIC
Core bandwidth and slew-rate ratings match, but the temperature range narrows from −40 °C to +85 °C to 0 °C to +70 °C

📋 Tham chiếu thay thế (không có trong danh mục)

LT1810IS8#TRPBF

✅ Drop-In
📦 8-pin SOIC
Same electrical ratings and 8-pin footprint; differs in tape-and-reel ordering and packing rather than core performance

📋 Tham chiếu thay thế (không có trong danh mục)

LT1810IS8 Tỷ lệ tối đa & tính chất điện

Number of Amplifiers 2 circuits
Amplifier Type General-purpose operational amplifier
Gain-Bandwidth Product 180 MHz at gain ≥ 10
Unity-Gain Bandwidth 320 MHz −3 dB
Slew Rate 350 V/µs
Output Current 85 mA
Input Range Rail-to-rail, including both supply rails
Output Range Rail-to-rail
Minimum Operating Temperature −40 °C
Maximum Operating Temperature +85 °C
Hộp 8-pin SOIC, 3.90 mm body width
Kiểu lắp đặt Surface mount
Lead-Free Status Available as LT1810IS8#PBF

Cấu hình chân LT1810IS8

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Chân 1 OUTA — Amplifier A output
Chân 2 INTA- — Inverting input for amplifier A
Chân 3 INTA+ — Non-inverting input for amplifier A
Chân 4 V- — Negative supply connection
Chân 5 INTB+ — Non-inverting input for amplifier B
Chân 6 INTB- — Inverting input for amplifier B
Chân 7 OUTB — Amplifier B output
Chân 8 V+ — Positive supply connection

Ứng dụng tiêu biểu

LT1810IS8 phù hợp cho 6 Áp dụngs: Photodiode Signal Conditioning, Video Interface Amplification, Pulse and Edge Signal Conditioning, Low-Voltage Data Acquisition, Active Filtering, Industrial Signal Conditioning.

📷

Photodiode Signal Conditioning

The LT1810IS8 is well suited to high-speed photodiode preamplification because its 320 MHz −3 dB unity-gain bandwidth supports wideband optical-signal conditioning and its 350 V/µs slew rate preserves fast transition edges. The dual SOIC package also allows a transimpedance stage and a follow-up gain or filtering stage to share one board area. Designers should account for photodiode capacitance, bias-resistor noise, and feedback stability when setting the closed-loop response.

📺

Video Interface Amplification

The LT1810IS8 can amplify or buffer low-voltage video signals when broad bandwidth and fast settling behavior matter. Its 180 MHz gain-bandwidth product at gains of 10 or higher and 320 MHz unity-gain bandwidth provide ample margin for common video-conditioning stages, while rail-to-rail input and output operation supports low-voltage systems. PCB implementation should minimize trace length around the amplifier and preserve the impedance environment needed for stable high-speed feedback.

⚡

Pulse and Edge Signal Conditioning

For pulse instrumentation, edge-triggered sensing, and fast control signals, the LT1810IS8 combines a 350 V/µs slew rate with an 85 mA output-current capability. These specifications help the dual amplifier reproduce rapidly changing waveforms without the severe large-signal distortion associated with slower amplifiers. Use short feedback paths and appropriate output loading, and confirm that downstream protection networks do not add excessive capacitance that could disturb stability.

🖥️

Low-Voltage Data Acquisition

The LT1810IS8 is appropriate for front-end amplification ahead of high-speed converters when the sensor or source operates from a low-voltage rail. Rail-to-rail inputs improve usable signal range, while the 180 MHz closed-loop capability supports wideband data paths. The dual configuration can provide gain in one channel and buffering, level translation, or active filtering in the other. Compensation, sampling, and converter-impedance requirements should be evaluated together to avoid loading errors.

🔧

Active Filtering

The LT1810IS8 can implement wideband active filters and fast closed-loop signal-conditioning blocks because its high gain-bandwidth product and slew rate reduce the bandwidth and edge-rate limitations encountered in lower-speed amplifiers. The 8-pin SO package simplifies conventional dual-op-amp filter layouts. Component tolerances, op-amp noise, parasitic capacitance, and the required Q factor should be calculated before finalizing values, particularly for filters with high gain or narrow transition bands.

🏭

Industrial Signal Conditioning

The LT1810IS8 industrial-temperature version supports signal conditioning in equipment where the −40 °C to +85 °C range and high-speed response are required. Rail-to-rail operation is valuable in low-voltage industrial controls, while the dual amplifier can reduce component count in multichannel designs. PCB creepage, grounding, noise isolation, and thermal performance should be assessed at the enclosure level, and the LT1810CS8#PBF alternative should be avoided where temperatures fall outside its 0 °C to +70 °C rating.

Tóm tắt các sản phẩm được đề xuất

LT1810IS8#PBF Lead-free ordering option for the same amplifier configuration Được sử dụng trong: Photodiode Signal Conditioning, Video Interface Amplification, Pulse and Edge Signal Conditioning, Low-Voltage Data Acquisition, Active Filtering, Industrial Signal Conditioning LT1809IS8#PBF Lower-bandwidth single-family counterpart Được sử dụng trong: Photodiode Signal Conditioning, Active Filtering LT1810IS8#TRPBF Tape-and-reel ordering configuration Được sử dụng trong: Video Interface Amplification, Low-Voltage Data Acquisition, Industrial Signal Conditioning LT1810CS8#PBF Commercial-temperature family alternative Được sử dụng trong: Pulse and Edge Signal Conditioning
What are the key specifications of LT1810IS8?
The LT1810IS8 is a dual rail-to-rail operational amplifier with a 180 MHz gain-bandwidth product, 320 MHz −3 dB unity-gain bandwidth, 350 V/µs slew rate, and 85 mA output-current capability. According to the Analog Devices LT1809/LT1810 manufacturer datasheet, it uses the standard dual-op-amp pinout in an 8-pin SO package. These characteristics make it suitable for high-speed, low-voltage signal conditioning.
What is the operating voltage range of LT1810IS8?
The operating voltage range is not stated in the manufacturer product summary available for this component. The Analog Devices datasheet confirms rail-to-rail input and output behavior, but engineers should consult its electrical-characteristics table for the exact minimum and maximum supply voltages before designing a rail. Use the Request a Quote form on this page if a controlled copy of the current documentation is needed.
Where can I download the LT1810IS8 datasheet PDF?
The official LT1810IS8 datasheet PDF is available from Analog Devices through the LT1809/LT1810 data-sheet URL listed on this page. The document covers the dual LT1810 in 8-pin SO and MSOP packages, including its standard dual-op-amp pinout. Use the manufacturer's pin-description table when assigning PCB signals and confirm the package suffix before releasing a layout.
Where can I find the LT1810IS8 pinout?
The LT1810IS8 uses the standard dual-operational-amplifier arrangement in an 8-pin SO package. According to the Analog Devices manufacturer datasheet, pins 1 and 7 are the two outputs, pins 2 and 6 are inverting inputs, pins 3 and 5 are non-inverting inputs, pin 4 is the negative supply, and pin 8 is the positive supply. Verify these assignments against the current datasheet before fabrication.
Is LT1810IS8 suitable for high-speed photodiode amplification?
Yes, the LT1810IS8 is suitable for photodiode front ends that need high bandwidth and rapid transient response. Its 320 MHz unity-gain bandwidth handles fast signals, while the 350 V/µs slew rate limits large-signal edge-rate distortion. The rail-to-rail input stage is useful in low-voltage systems, although photodiode biasing, capacitance, noise, and feedback stability still require separate design.
Where to buy LT1810IS8 online?
Use the Request a Quote form on this page to request LT1810IS8 availability, current commercial terms, and suitable order quantities. The form allows the request to be directed to XAIPART without relying on a static distributor listing. Package, quantity, and delivery requirements should be stated because the LT1810IS8 is also identified under several ordering suffixes.
What is the price of LT1810IS8?
The current commercial price for LT1810IS8 should be obtained through the Request a Quote form on this page. Quote-based ordering allows the exact suffix, packing method, quantity, and delivery terms to be evaluated together. Static pricing can become stale quickly for high-speed analog amplifiers, particularly when tube and tape-and-reel configurations are mixed.
What is the lead time for LT1810IS8?
Request the current lead time through the Request a Quote form on this page and include the required quantity, package suffix, and shipment destination. Lead time can vary with manufacturer inventory, order size, and assembly or cut-tape requirements. For production planning, request a dated schedule rather than relying on a generic catalog availability statement.
Is LT1810IS8 in stock?
Current stock for LT1810IS8 should be confirmed through the Request a Quote form on this page. The request should identify whether the order is for the base LT1810IS8 designation, a lead-free ordering suffix, tube packing, or tape-and-reel delivery. This avoids ambiguity between electrically equivalent order codes that can have different handling requirements.
What is the best drop-in replacement for LT1810IS8?
LT1810IS8#PBF is the closest lead-free ordering option identified for the same LT1810 electrical configuration and 8-pin SO footprint. Its core performance remains the 180 MHz gain-bandwidth product, 320 MHz unity-gain bandwidth, and 350 V/µs slew rate. Confirm the exact suffix, temperature grade, packing method, and pin markings before treating it as a production replacement.
Can LT1810CS8#PBF replace LT1810IS8?
LT1810CS8#PBF can match the package and core amplifier topology, but its 0 °C to +70 °C temperature range differs from the LT1810IS8 industrial range of −40 °C to +85 °C. Use it only when the application remains within its temperature limits. For industrial environments, retain the broader LT1810IS8 temperature grade.
What can replace LT1810IS8?
A practical replacement must use the same 8-pin SO footprint, preserve the standard dual-op-amp pinout, and provide comparable bandwidth and slew-rate capability. LT1810IS8#PBF is the nearest ordering option, while LT1810CS8#PBF has the same package but a narrower temperature range. A cross-manufacturer substitute should be accepted only after its electrical limits and pinout are independently verified.
LT1810IS8 vs LT1809IS8#PBF — which is better for fast signals?
The LT1810IS8 is the better choice for fast signals because its gain-bandwidth product is 180 MHz and its slew rate is 350 V/µs, compared with 100 MHz and 200 V/µs for the LT1809IS8#PBF. Both are dual rail-to-rail devices in 8-pin SO packages, but the LT1810 provides substantially more bandwidth and edge-rate capability for photodiode, pulse, and video applications.
When should I choose LT1810IS8 over a lower-bandwidth dual op amp?
Choose LT1810IS8 when the signal path requires wide small-signal bandwidth or fast large-signal transitions. Its 320 MHz unity-gain bandwidth and 350 V/µs slew rate are materially stronger than those of a lower-bandwidth general-purpose dual amplifier. If the signal band is much narrower, a lower-power or lower-cost amplifier may be appropriate after checking output-current and distortion requirements.
What is the best Analog Devices equivalent for LT1810IS8?
LT1810IS8#PBF is the closest Analog Devices ordering alternative because it retains the LT1810 dual-amplifier configuration, 180 MHz gain-bandwidth product, 350 V/µs slew rate, and 8-pin SO footprint. The key differences concern ordering, lead-free processing, packing, and temperature suffix rather than the core analog performance. Confirm the required grade and shipping format.

Dữ liệu tham khảo kỹ thuật cho LT1810IS8 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the LT1810IS8 for low-voltage, high-speed dual signal conditioning when the circuit benefits from a 180 MHz gain-bandwidth product, 320 MHz unity-gain bandwidth, and 350 V/µs slew rate. Select LT1810IS8#PBF when a lead-free ordering code is required but the core electrical ratings and industrial temperature range remain unchanged. LT1810IS8#TRPBF provides the same core configuration in a tape-and-reel order format for automated assembly. Consider LT1810CS8#PBF only in commercial-temperature systems that remain within 0 °C to +70 °C. Avoid LT1809IS8#PBF when the design requires the LT1810’s 180 MHz bandwidth or 350 V/µs slew rate, because its 100 MHz bandwidth and 200 V/µs slew rate can introduce bandwidth and distortion limitations. For every option, confirm the exact pinout, supply limits, feedback network, and loading before PCB release.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này LT1810IS8#PBF LT1810CS8#PBF LT1810IS8#TRPBF
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Package 8-pin SOIC 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same
Number of Amplifiers 2 2 2 2
Gain-Bandwidth Product 180 MHz at gain ≥ 10 180 MHz at gain ≥ 10 180 MHz at gain ≥ 10 180 MHz at gain ≥ 10
Unity-Gain Bandwidth 320 MHz −3 dB 320 MHz −3 dB 320 MHz −3 dB 320 MHz −3 dB
Slew Rate 350 V/µs 350 V/µs 350 V/µs 350 V/µs
Output Current 85 mA 85 mA 85 mA 85 mA
Operating Temperature −40 °C to +85 °C −40 °C to +85 °C 0 °C to +70 °C −40 °C to +85 °C
Lead-Free Ordering Base IS8 designation #PBF lead-free designation #PBF lead-free designation #TRPBF tape-and-reel designation

Bảo phân biệt quan trọng

  • Higher speed than the closely related LT1809 (vsLT1809IS8#PBF)
  • Broader temperature coverage than the commercial-grade suffix (vsLT1810CS8#PBF)
  • Matching core performance with a lead-free ordering designation (vsLT1810IS8#PBF)

Ghi chú thiết kế

Place input, feedback, and compensation components directly beside their associated LT1810IS8 pins. High-speed feedback loops can pick up parasitic inductance and capacitance when connections are long, so use short traces, a continuous ground reference, and minimal loop area. Place supply-decoupling capacitance at the device rather than at the output of a remote regulator or cable.

Treat every LT1810IS8 output as a high-speed node. Avoid long unterminated PCB traces, provide a low-impedance return path, and match controlled-impedance interconnects when driving cables or downstream devices. The 350 V/µs slew rate can expose edge-rate problems that are invisible at low test frequencies, so evaluate the complete source-to-load path rather than only the amplifier in isolation.

Do not substitute the LT1809 family into a design that depends on LT1810 speed: its 100 MHz gain-bandwidth product and 200 V/µs slew rate are lower. Likewise, LT1810CS8#PBF is restricted to 0 °C through +70 °C. Confirm package suffix, temperature grade, pinout, and feedback compensation together; matching only the eight-pin outline does not establish drop-in suitability.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Yes
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The LT1810IS8#PBF ordering designation identifies a lead-free option. No explicit RoHS, REACH, halogen-free, conflict-minerals, or automotive-qualification statement was established.

Dữ liệu được xác minh vào: 2026-11-19 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

LT1810IS8 datasheet LT1810IS8 datasheet pdf LT1810IS8 pinout LT1810IS8 schematic LT1810IS8 equivalent LT1810IS8 replacement LT1810IS8 vs LT1809IS8#PBF LT1810IS8 180MHz amplifier LT1810IS8 350V/us LT1810IS8 SOIC-8 footprint Analog Devices LT1810IS8 LT1810IS8 price LT1810IS8 stock LT1810IS8 photodiode amplifier

Các bộ phận và thuật ngữ liên quan

Analog Devices Linear Technology LT1810IS8 LT1810IS8#PBF LT1810CS8#PBF LT1810IS8#TRPBF LT1809IS8#PBF operational amplifier dual amplifier rail-to-rail input rail-to-rail output low-distortion amplifier gain-bandwidth product unity-gain bandwidth slew rate 85 mA output current 8-pin SOIC SOIC package surface-mount package signal conditioning photodiode amplification video signal conditioning active filtering pulse signal conditioning low-voltage data acquisition
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ