MAX1165ACUI+ - 16-Bit 165ksps SAR ADC, Parallel | Maxim
部品番号: MAX1165ACUI+ ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $9.85 | $9.85 |
| 10 | $8.95 | $89.50 |
| 100 | $7.65 | $765.00 |
| 500 | $6.8 | $3,400.00 |
| 1,000 | $6.1 | $6,100.00 |
MAX1165ACUI+ 概要
An ADC (Analog-to-Digital Converter) is a mixed-signal data converter that transforms a continuous analog voltage into a discrete digital code, enabling microcontrollers, FPGAs, and DSPs to process real-world sensor and instrumentation signals. Successive-approximation ADCs use an internal binary-search algorithm combined with an internal DAC to resolve the input one bit per clock cycle, balancing speed, resolution, and power consumption. The MAX1165 family sits in the precision mid-speed converter segment of the data-converter hierarchy: ADC -> SAR ADC -> precision data converter -> mixed-signal IC -> semiconductor.
Key specifications include 16-bit resolution with no missing codes, ±1 LSB INL (typical), ±0.5 LSB DNL (typical), and an aperture bandwidth compatible with 165 ksps throughput. The parallel interface (8+8 byte-mode or 16-bit word-mode) provides glitch-free readback without the timing overhead of a serial ADC, and the part offers software-configurable input ranges via the input scaling network. The TSSOP-28 footprint gives a compact 0.65 mm pitch, surface-mount solution suitable for high-density data-acquisition boards.
Typical applications include industrial process-control loops, portable instrumentation and data loggers, battery-powered medical monitors, and multi-channel data-acquisition front ends using an external MUX. The wide input range and integrated reference simplify board-level design, while parallel output enables direct connection to a microcontroller external memory bus for high-throughput captures.
When designing with this device, ensure the analog input is bandwidth-limited (RC filter, typically 1 kΩ/1 nF) to avoid aliasing, and add 0.1 µF decoupling close to AVDD and DVDD. The PD pin can be tied to a microcontroller GPIO for power management in portable designs. Compute scheme, supplier scheme, and pin-compatible Scheme B variants are summarized in the comparison table below.
ドロップイン代替品: MAX1165ACUI+ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MAX1165ACUI+ （同一形状・フットプリント） — 相違点: Package, Analog Supply Voltage, Digital Supply Voltage, Operating Temperature, Input Type.
クイック比較ツール — 並列比較する代替部品を選択:
MAX1166ACUI+
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MAX1165BCUI+
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MAX1165AEUI+
✅ ドロップイン✓ 在庫あり
$7.95 / 個
データシートを見る →MAX1166BEUI+
✅ ドロップイン📋 参考代替品（カタログ未掲載）
AD7606BSTZ
✅ ドロップイン✓ 在庫あり
$16.9 / 個
データシートを見る →MAX1165ACUI+ 最大定格＆電気的特性
| Number of Bits | 16 |
| サンプリングレート | 165 ksps |
| Number of Input Channels | 1 (Single-Ended) |
| Input Type | Single-Ended, configurable scaling |
| Architecture | SAR (Successive Approximation) |
| Data Interface | Parallel, 8+8 byte mode / 16-bit word mode |
| Track-and-Hold Ratio (S/H:ADC) | 1:1 (integrated) |
| Number of A/D Converters | 1 |
| Reference Type | Internal 4.096 V (external option) |
| Configuration | S/H-ADC |
| Supply Voltage (Analog) | 4.75 V to 5.25 V |
| Supply Voltage (Digital) | 4.75 V to 5.25 V |
| 動作温度 | 0 C to +70 C (Commercial) |
| パッケージ | TSSOP-28 |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant (Pb-free suffix '+') |
| Lead-Free | Yes (suffix '+') |
MAX1165ACUI+ ピン構成
| ピン 1 | AIN — Analog Input |
| ピン 2 | AVDD — Analog +5 V Supply |
| ピン 3 | AGND — Analog Ground |
| ピン 4 | REF — Reference (Internal 4.096 V / External) |
| ピン 5 | REFGND — Reference Ground |
| ピン 6 | PD — Power-Down Input (active high) |
| ピン 7 | CS — Chip Select (active low) |
| ピン 8 | RD — Read Strobe (active low) |
| ピン 9 | HBEN — High-Byte Enable (selects 8/16-bit mode) |
| ピン 10 | D0 — Data Bit 0 (LSB) |
| ピン 11 | D1 — Data Bit 1 |
| ピン 12 | D2 — Data Bit 2 |
| ピン 13 | D3 — Data Bit 3 |
| ピン 14 | D4 — Data Bit 4 |
| ピン 15 | D5 — Data Bit 5 |
| ピン 16 | D6 — Data Bit 6 |
| ピン 17 | D7 — Data Bit 7 |
| ピン 18 | DVDD — Digital +5 V Supply |
| ピン 19 | DGND — Digital Ground |
| ピン 20 | D8 — Data Bit 8 |
| ピン 21 | D9 — Data Bit 9 |
| ピン 22 | D10 — Data Bit 10 |
| ピン 23 | D11 — Data Bit 11 |
| ピン 24 | D12 — Data Bit 12 |
| ピン 25 | D13 — Data Bit 13 |
| ピン 26 | D14 — Data Bit 14 |
| ピン 27 | D15 — Data Bit 15 (MSB) |
| ピン 28 | CLK — External Conversion Clock |
主な用途
MAX1165ACUI+ の用途: 6 件s: Industrial Process-Control Data Acquisition, Portable Battery-Powered Instrumentation, Medical Patient Monitoring Equipment, Multi-Channel Data Acquisition Front End, Weigh Scale and Strain-Gauge Front End, Audio and Acoustic Measurement Systems.
Industrial Process-Control Data Acquisition
The MAX1165ACUI+'s 16-bit resolution and 165 ksps sampling rate suit industrial process-control loops where a microcontroller reads analog signals from 4-20 mA transmitters, RTDs, or strain-gauge bridges. Its 5 V analog supply matches industrial +5 V sensor rails; the parallel interface avoids serial-clock overhead, allowing deterministic burst captures for PID loops. The integrated 4.096 V reference scales a 0-4.096 V input to a full 16-bit code (244 µV/LSB), and the track-and-hold front end settles within 200 ns. Compared to a serial ADC, the parallel interface removes SPI bit-banging from the controller firmware, simplifying real-time control code while still drawing under 10 mA total supply current during continuous conversion.
おすすめ
Portable Battery-Powered Instrumentation
The MAX1165ACUI+'s automatic power-down reduces supply current to microampere levels between samples - critical for battery-powered handheld instruments such as digital multimeters, portable scales, and field medical monitors. A microcontroller can take single conversions on demand, then power down the ADC between readings, extending battery life by 10-100x compared to a continuously-sampling ADC. The 5 V supply is compatible with four-cell NiMH packs (4.8 V nominal) or single-cell Li-ion with a boost converter. The TSSOP-28 package keeps the board footprint small (9.7 x 6.4 mm), and the parallel interface lets a low-cost 8051 or PIC microcontroller read conversion results without an SPI peripheral - valuable for cost-sensitive portable designs.
おすすめ
Medical Patient Monitoring Equipment
Medical patient-monitoring equipment (ECG, SpO2, blood-pressure modules) requires 16-bit resolution to capture small biopotential signals while rejecting quantization noise in the diagnostic bandwidth. The MAX1165ACUI+ samples ECG front-end outputs at up to 165 ksps, providing >80 kHz Nyquist bandwidth - more than sufficient for 500 Hz ECG plus respiration channels. Its single-ended input simplifies front-end design versus differential ADCs, and the integrated 4.096 V reference removes the need for an external precision reference, reducing BOM count for cost-sensitive medical devices. The 16-bit no-missing-codes performance ensures clean baseline traces for diagnostic algorithms, and the TSSOP-28 package supports the compact form factor of modern wearable medical devices.
おすすめ
Multi-Channel Data Acquisition Front End
Multi-channel data-acquisition boards (used in test & measurement, vibration analysis, and industrial data loggers) typically combine an external analog MUX (such as a MAX1156 or MAX306) with a fast SAR ADC. The MAX1165ACUI+ serves as the converter downstream of the MUX, with its 5 µs conversion time allowing each channel to be sequentially acquired at high effective throughput (10+ ksps per channel). The parallel output bus allows an FPGA or DSP to ingest conversion data directly without serial overhead, supporting deterministic sampling for vibration and modal-analysis applications. The 16-bit no-missing-codes performance captures dynamic range typical of strain-gauge and load-cell inputs, and the 5 V supply rails are easy to derive from common +5 V and +12 V analog board rails.
おすすめ
Weigh Scale and Strain-Gauge Front End
Weigh scales and force-measurement instruments rely on 16+ bit ADC resolution to resolve small load-induced bridge voltages. The MAX1165ACUI+ digitizes the differential bridge output (after an external instrumentation amplifier such as the MAX1162 or AD8421) with 16-bit resolution, giving 244 µV LSB at 4.096 V full-scale - sufficient for 0.01% resolution in 4-digit industrial scales. The internal reference provides a stable excitation-derived full-scale calibration point, simplifying firmware calibration. The automatic power-down feature extends battery operation for handheld scales; the TSSOP-28 footprint suits compact scale-controller boards where board area is at a premium.
おすすめ
Audio and Acoustic Measurement Systems
Audio-bandwidth measurement systems (sound-level meters, acoustic analyzers, ultrasonic flaw detectors) require 16-bit resolution and sampling rates of at least 44.1 ksps. The MAX1165ACUI+'s 165 ksps throughput provides 3x oversampling at CD-quality audio rates, reducing analog anti-aliasing filter complexity. The integrated track-and-hold and 16-bit no-missing-codes performance capture acoustic transients with high dynamic range, and the parallel interface allows a DSP to ingest conversion data at full bus bandwidth. The 5 V analog supply rails align with op-amp audio signal chains (MAX4475, OPA1612, AOP621) without requiring level shifting, and the TSSOP-28 package suits handheld acoustic-analyzer enclosures.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MAX1165ACUI+ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX1166ACUI+ | MAX1165BCUI+ | MAX1165AEUI+ | MAX1166BEUI+ | AD7606BSTZ |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Analog Devices |
| Package | TSSOP-28 | TSSOP-28 - same | TSSOP-28 - same | TSSOP-28 - same | TSSOP-28 - same | TSSOP-28 - same footprint (verify pinout) |
| Resolution | 16-bit | 16-bit | 16-bit | 16-bit | 16-bit | 16-bit |
| Sampling Rate | 165 ksps | 165 ksps | 165 ksps | 165 ksps | 165 ksps | 200 ksps (+21%) |
| Input Channels | 1 single-ended | 1 single-ended | 1 single-ended | 1 single-ended | 1 single-ended | 8 single-ended/bipolar (+700%) |
| Operating Temperature | 0 to +70 C (Commercial) | -40 to +125 C (Industrial/Automotive) | 0 to +70 C (Commercial) | -40 to +85 C (Extended) | -40 to +125 C (Industrial/Automotive) | -40 to +85 C (Industrial) |
| Supply Voltage | +5 V single supply | +5 V single supply | +5 V single supply | +5 V single supply | +5 V single supply | +5 V analog / +3.3 V or +5 V digital |
| Reference | Internal 4.096 V | Internal 4.096 V | Internal 4.096 V | Internal 4.096 V | Internal 4.096 V | External 2.5 V reference required |
| Interface | Parallel (8/16-bit) | Parallel (8/16-bit) | Parallel (8/16-bit) | Parallel (8/16-bit) | Parallel (8/16-bit) | Parallel + Serial (SPI) |
| Lifecycle | Obsolete | Active (last-time-buy post-2026) | Obsolete | Obsolete | Active | Active |
主な差別化要因
- Parallel interface with 16-bit single-cycle readback （vs MAX1162ACUB+T)
- Integrated 4.096 V precision reference （vs MAX1156AEUP+T)
- Industrial/automotive upgrade path available (MAX1166) （vs AD7606BSTZ)
設計ノート
The MAX1605ACUI+ (sic: MAX1165ACUI+) draws approximately 8 mA from AVDD and 1 mA from DVDD during continuous 165 ksps conversion. Decoupling: place a 10 µF tantalum plus 0.1 µF ceramic on AVDD, and a 1 µF ceramic plus 0.1 µF ceramic on DVDD, both within 5 mm of the supply pins. Estimated supply current at 1 ksps with PD active between conversions drops to ~50 µA average - useful for battery-powered portable designs.
Separate analog and digital ground planes joined only at the AGND/DGND pins. Route the analog input AIN on the analog side of the board, away from the parallel data bus (D0-D15) and the CLK trace - parallel data edges are a known coupling source into the analog input. Estimated: an ungrounded guard trace around AIN reduces digital-coupling noise by ~6 dB in a typical TSSOP-28 layout.
Add a 1 kΩ resistor and 1 nF capacitor anti-aliasing RC filter at the AIN pin; the -3 dB cutoff at 160 kHz is well above the 165 ksps Nyquist bandwidth (82.5 kHz). For clean switching effects, keep the analog input bandwidth well below Nyquist to avoid aliased spurs. The internal track-and-hold settles within 200 ns; allow at least 250 ns acquisition time before initiating conversion for full 16-bit accuracy.
Three common pitfalls to watch for. (1) Don't omit HBEN tie-up/down - leaving HBEN floating causes intermittent 8/16-bit bus mode errors. (2) Don't drive CS and RD simultaneously without checking the read-cycle timing - the datasheet t_CSS / t_RS parameters are 10 ns minimum. (3) Don't apply analog inputs before AVDD ramps or latch-up can occur - the analog input ESD structure rating is 1000 V HBM, so avoid unpowered transient overvoltage events.
コンプライアンス情報
Pb-free suffix '+' confirms RoHS compliance. Reach compliant per manufacturer declaration. Commercial temperature grade only; choose MAX1166 for AEC-Q100 grade.
