Analog Devices

MAX211CWI+T - 4/5 RS-232 Transceiver, 120kbps | Analog Devices

部品番号: MAX211CWI+T ✓ 生産中
+5 V Vdss 28-pin wide SOIC Package
MOQ: 1 |

MAX211CWI+T 概要

Analog Devices MAX211CWI+T is a 4/5-channel RS-232 transceiver for V.28 communication interfaces, supporting data rates in excess of 120kbps from a single +5V supply in a 28-pin wide SOIC package. Its integrated charge-pump circuitry generates the bipolar voltage levels required by the drivers without a separate ±12V supply. The receiver also supports low-power operation through shutdown control, while four external 0.1µF capacitors support the on-chip charge-pump design.

An RS-232 transceiver is an interface IC that combines drivers and receivers for point-to-point serial communication. In this device family, the transmitter converts TTL or CMOS logic signals into EIA/TIA-232E levels, and the receiver converts bipolar serial data back into logic levels. The MAX211 family belongs to the broader RS-232 interface category within interface ICs and semiconductor communication devices.

The principal features are four drivers, five receivers, operation from a single +5V supply, data rates above 120kbps, and driver output levels of ±5V under the specified EIA/TIA-232E load. The integrated charge-pump circuitry eliminates the need for a separate negative supply rail, while shutdown support permits the device to be placed into a low-power state when communication is not required.

The MAX211 architecture separates the interface into charge-pump voltage conversion, driver, receiver, and control sections. Four 0.1µF external capacitors are specified for operation with the charge-pump circuitry. This arrangement supports compact single-supply RS-232 designs while preserving familiar bipolar signaling at the connector and cable interface.

Typical uses include industrial serial links, data-acquisition equipment, point-of-sale systems, test equipment, and embedded control systems that exchange RS-232 signals over cable. The interface is especially appropriate when legacy equipment expects ±5V RS-232 levels but the internal system supplies only +5V logic power.

When laying out the circuit, place the four 0.1µF charge-pump capacitors close to their specified pins and keep the device ground connection compact. Confirm that the selected connector and cable interface use EIA/TIA-232E signal levels rather than RS-422 or RS-485, since the logic levels and voltage polarity are not interchangeable.

This product summary combines the manufacturer's electrical and package details with application guidance, pinout considerations, comparison criteria, and design notes intended to help engineers shorten evaluation and prototype time. For purchasing decisions, request a quote on this page for current commercial terms and manufacturing support.

ドロップイン代替品: MAX211CWI+T — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: MAX211CWI+T (同一形状・フットプリント) — 相違点: Supply Voltage, Package, Communication Standard, Product Type.

Analog Devices
Supply Voltage: 4.5V to 5.5V
Product Type: RS-232 and V.28 transceiver
比較対象 MAX211CWI+T →
Maxim Integrated
Supply Voltage: 5V
Package: 28-SOIC (WSOIC)
Communication Standard: RS-232 and V.28
比較対象 MAX211CWI+T →

MAX211ECWI+T

✅ ドロップイン
📦 28-SOIC
Uses the extended-temperature ordering option; the cross-reference result identifies no change in the 4/5-channel +5V RS-232 architecture or 28-SOIC footprint

📋 参考代替品(カタログ未掲載)

MAX213CWI+T

✅ ドロップイン ⚠️ 仕様未検証
📦 28-SOIC
Related MAX213 family device with different shutdown-control behavior; it retains the single +5V, 4/5 RS-232, 120kbps-class, and 28-SOIC architecture

📋 参考代替品(カタログ未掲載)

MAX211CWI+

✅ ドロップイン ⚠️ 仕様未検証
Analog Devices
📦 28-SOIC
RS-232 and V.28 transceiver · 4.5V to 5.5V · 4 · 5 · In excess of 120kbps · 4 x 0.1uF · ±5V EIA/TIA-232E levels · Single +5V supply

価格はお問い合わせください

データシートを見る →

MAX211ECWI+

✅ ドロップイン ⚠️ 仕様未検証
Maxim Integrated
📦 28-SOIC
RS-232 transceiver · RS-232 and CMOS · 5V · 4 drivers · 5 receivers · RS-232 and V.28 · ±15kV · 4 x 0.1uF

価格はお問い合わせください

データシートを見る →

MAX213ECWI+T

✅ ドロップイン ⚠️ 仕様未検証
📦 28-SOIC
Extended-temperature MAX213 family option with different shutdown-control behavior while retaining the 28-SOIC, single +5V, and 4/5 RS-232 architecture

📋 参考代替品(カタログ未掲載)

MAX211CWI+T 仕様

Product Type 4/5 RS-232 transceiver
Driver Count 4 drivers
Receiver Count 5 receivers
電源電圧 +5 V
Maximum Data Rate In excess of 120kbps
Driver Output Signal Level ±5 V
Communication Standard EIA/TIA-232E
Protocol RS-232 / V.28
Charge Pump Integrated
External Capacitor Quantity 4 capacitors
External Capacitor Value 0.1µF
パッケージ 28-pin wide SOIC
実装タイプ Surface mount

MAX211CWI+T 28-pin wide soic ピン配置ガイド

MAX211CWI+T (28-pin wide soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

MAX211CWI+T の 28-pin wide soic パッケージピン配置図

詳細なピン配置データはありません: MAX211CWI+T.

詳細は データシート をご参照ください。

主な用途

MAX211CWI+T の用途: 6 件s: Industrial RS-232 Control Links, Point-of-Sale Terminal Interfaces, Data-Acquisition Equipment, Embedded Service Interfaces, Test and Measurement Systems, Network Management and Maintenance Ports.

🏭

Industrial RS-232 Control Links

The MAX211CWI+T fits legacy industrial controllers, barcode equipment, and service interfaces that require RS-232 communication from a single +5V supply. Its four drivers and five receivers support several channels on one board without separate negative supply rails. The integrated charge pump produces the bipolar signal levels required by EIA/TIA-232E receivers, while operation above 120kbps accommodates moderately high-speed legacy links. Keep the four 0.1µF capacitors close to their associated pins and provide a low-impedance ground path to the connector to minimize common-impedance disturbances.

🖥️

Point-of-Sale Terminal Interfaces

Point-of-sale systems often combine a host processor with printers, scanners, and customer displays connected through established RS-232 ports. The MAX211CWI+T provides four transmitters and five receivers, allowing multiple point-to-point channels while accepting a compact single +5V system supply. Its ±5V EIA/TIA-232E driver levels and data rates in excess of 120kbps support common serial peripheral arrangements. Validate each cable length, baud rate, grounding method, and connector pin assignment because legacy RS-232 implementations vary in flow control and signal naming.

📡

Data-Acquisition Equipment

Laboratory and industrial data-acquisition units can use the MAX211CWI+T to connect a controller to RS-232 instruments, adapters, and service ports. The five receivers provide flexible channel availability for status, request, and data signals, while four drivers cover common command outputs. A single +5V supply simplifies instrumentation power architecture, and the integrated charge pump avoids external negative rail generation. Because the interface supports data rates in excess of 120kbps, engineers can evaluate faster legacy links while still checking the cable, termination, grounding, and receiver-load constraints of the complete system.

🔧

Embedded Service Interfaces

Embedded equipment often retains an RS-232 service port for configuration, diagnostics, or firmware recovery even when its main processor uses modern high-speed serial links. The MAX211CWI+T adds four drivers and five receivers in a 28-pin wide SOIC package without requiring a separate ±12V supply. Its integrated charge-pump circuitry supports single +5V operation, while the 120kbps-class performance is suitable for many configuration protocols. Provide controlled access to the service connector and review the maximum cable length and ground-reference arrangement to avoid functional problems in deployed installations.

🧪

Test and Measurement Systems

The MAX211CWI+T can bridge a test controller to legacy instruments that use only RS-232 communication. Four driver channels and five receiver channels allow command, trigger, measurement, and status signals to be consolidated on one interface IC. Operation from +5V simplifies instrument subassembly design, and the integrated charge pump generates the required bipolar transmit levels. At data rates in excess of 120kbps, the device can support fast legacy transfer modes, although cable routing, grounding, shielding, and loading still determine practical reliability in laboratory environments.

🌐

Network Management and Maintenance Ports

Networked appliances and communication equipment can retain an RS-232 maintenance channel for initial configuration and field diagnostics. The MAX211CWI+T is suited to this role because it provides several receive and transmit channels from one +5V supply while maintaining ±5V EIA/TIA-232E output levels. The 28-pin wide SOIC package allows a compact implementation, and data rates above 120kbps support routine configuration transfers. Design the maintenance connector for dependable grounding, avoid long unprotected cable runs, and confirm that the equipment's administrative software uses compatible baud rates, parity, and flow-control settings.

おすすめ製品の概要

MAX213CWI+T Related single-supply RS-232 transceiver family member 使用用途: Industrial RS-232 Control Links, Embedded Service Interfaces, Test and Measurement Systems MAX211ECWI+T Extended-temperature ordering option 使用用途: Industrial RS-232 Control Links, Point-of-Sale Terminal Interfaces, Test and Measurement Systems MAX211CWI Same MAX211 interface family 使用用途: Point-of-Sale Terminal Interfaces MAX213ECWI+T Related MAX213 interface option 使用用途: Data-Acquisition Equipment, Network Management and Maintenance Ports MAX211ECWI Same-family extended-temperature option 使用用途: Data-Acquisition Equipment, Network Management and Maintenance Ports MAX211CWI+T Analog Devices 使用用途: Embedded Service Interfaces
What is the MAX211CWI+T?
The MAX211CWI+T is a 4/5-channel RS-232 transceiver that operates from a single +5V supply and supports data rates in excess of 120kbps. According to the Analog Devices MAX211 product page, it combines four drivers, five receivers, and integrated charge-pump circuitry in a 28-pin wide SOIC package. It is intended for RS-232 and V.28 interfaces where separate positive and negative power rails are undesirable.
What are the key specifications of MAX211CWI+T that engineers should know?
The MAX211CWI+T provides four RS-232 drivers, five receivers, single-supply +5V operation, and data rates above 120kbps. Its drivers maintain approximately ±5V EIA/TIA-232E output levels when loaded according to the interface requirements. The device uses integrated charge-pump circuitry and four external 0.1µF capacitors, all housed in a 28-pin wide SOIC package.
What is the operating voltage of MAX211CWI+T?
The MAX211CWI+T operates from a single +5V supply. According to the Analog Devices MAX211 product information, its integrated charge-pump circuitry generates the voltage levels needed by the RS-232 drivers, avoiding a separate negative supply. The interface also supports a low-power shutdown function for systems that do not require continuous communication.
What is the maximum data rate of MAX211CWI+T?
The MAX211CWI+T supports data rates in excess of 120kbps. The Analog Devices product page states that the drivers maintain ±5V EIA/TIA-232E output signal levels at those rates when loaded in accordance with the standard. Actual link performance can also depend on cable length, receiver load, baud-rate tolerance, and signal-integrity margin in the complete interface.
Where can I download the MAX211CWI+T datasheet PDF?
The MAX211CWI+T datasheet and product resources are available through the official Analog Devices MAX211 product page at https://www.analog.com/en/products/max211.html. Use the manufacturer datasheet for the authoritative pin-description table, recommended charge-pump capacitors, electrical characteristics, and operating limits. The same family is also identified by the base ordering code MAX211CWI, while the +T suffix denotes the tape-and-reel shipping format.
Where is the MAX211CWI+T pinout?
The MAX211CWI+T pinout is defined in the MAX211 manufacturer datasheet and its 28-pin wide SOIC package drawing. Assign PCB connections from the datasheet pin-description table, especially the charge-pump capacitor pins, driver outputs, receiver inputs, enable controls, and supply connections. The visible package diagram on this page uses a generic representation because the component library does not contain a dedicated 28-pin SOIC drawing.
Can MAX211CWI+T operate without a negative supply voltage?
Yes. The MAX211CWI+T uses integrated charge-pump circuitry to support RS-232 operation from a single +5V supply. According to the Analog Devices MAX211 product information, this architecture suits equipment that cannot provide the traditional ±12V RS-232 supply rails. Four external 0.1µF capacitors are associated with the charge-pump section and should be placed close to the specified pins.
Where to buy MAX211CWI+T online?
Use the Request a Quote form on this page to request MAX211CWI+T availability, commercial terms, and order support. The component is an Analog Devices MAX211-family 4/5 RS-232 transceiver in a 28-pin wide SOIC package. The request can specify the required quantity, shipment destination, target date, and whether reel packaging or production quantities are required.
What is the price of MAX211CWI+T?
Current pricing for MAX211CWI+T should be requested through the Request a Quote form on this page because commercial terms can vary with quantity, packaging, and shipment requirements. The device is identified as a +5V, 4/5 RS-232 transceiver with four external 0.1µF capacitors in a 28-pin wide SOIC package. Submit the required quantity and production schedule with the request.
What is the lead time for MAX211CWI+T?
Request the current lead time for MAX211CWI+T through the Request a Quote form on this page. Lead time can depend on order quantity, reel availability, production schedule, and shipment destination, so include the required delivery date in the request. The manufacturer product information identifies the MAX211CWI+T as a +5V RS-232 transceiver with integrated charge-pump circuitry.
Is MAX211CWI+T in stock?
Request current MAX211CWI+T stock and allocation through the Request a Quote form on this page. Include the required quantity, packaging preference, ship-to region, and target date so the commercial response can reflect the actual order configuration. The device is a 28-pin wide SOIC, 4/5-channel RS-232 interface operating from a single +5V supply.
What is the best drop-in replacement for MAX211CWI+T?
The MAX211ECWI+T is the closest documented drop-in option because it retains the same 4/5 RS-232 architecture and 28-pin wide SOIC footprint while changing the temperature-range ordering option. According to the cross-reference results, both devices use +5V operation, integrated charge-pump circuitry, and four 0.1µF external capacitors. Verify the exact electrical limits and temperature grade before production substitution.
Can MAX211ECWI+T replace MAX211CWI+T?
The MAX211ECWI+T can serve as a candidate replacement for the MAX211CWI+T because both are 4/5 transceivers in the same 28-pin wide SOIC family and share the +5V charge-pump implementation. The cross-reference comparison identifies a temperature-grade distinction rather than a package change. Confirm pin functions, operating-temperature requirements, and lifecycle status against the manufacturer documentation before approving the substitution.
When should I choose MAX211CWI+T over MAX211ECWI+T?
Choose MAX211CWI+T when the design's required operating-temperature range is satisfied by the standard grade, and choose MAX211ECWI+T when a broader temperature-range option is necessary. Both devices use the same 28-pin wide SOIC footprint and support the same four-driver, five-receiver RS-232 function with data rates in excess of 120kbps. The decisive consideration is the environmental rating required by the target equipment.
MAX211CWI+T vs MAX213CWI+T - which is better for a +5V RS-232 design?
The MAX211CWI+T is appropriate when the design requires the established 4/5 MAX211 transceiver function, while the MAX213CWI+T belongs to the related MAX213 family and adds a different low-power shutdown arrangement. Both are associated with the MAX200-MAX209, MAX211, and MAX213 single-supply transceiver family and use 28-pin wide SOIC options. Confirm exact pin functions and shutdown timing before treating either device as interchangeable.
Is MAX211CWI+T suitable for industrial serial communication?
The MAX211CWI+T is suitable for single-supply RS-232 links when its specified electrical and temperature limits satisfy the application. It supports four drivers, five receivers, ±5V EIA/TIA-232E driver levels, and data rates in excess of 120kbps. Industrial suitability should be checked against the required ambient temperature, isolation strategy, surge environment, cable length, and connector grounding strategy.
What can replace MAX211CWI+T?
The MAX211ECWI+T is the closest documented replacement candidate for the MAX211CWI+T because it preserves the 28-pin wide SOIC footprint, four drivers, five receivers, single +5V supply, and four external 0.1µF capacitors. The main visible ordering distinction is the temperature grade. Validate the complete pin map and electrical limits before substituting it into an existing board.

エンジニアリング参考データ: MAX211CWI+T — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the MAX211CWI+T for a conventional 4/5-channel RS-232 interface that uses a single +5V supply, requires data rates above 120kbps, and fits a 28-pin wide SOIC footprint. Select MAX211ECWI+T when the equipment needs the extended-temperature ordering option while retaining the same MAX211 architecture and PCB land pattern. Consider MAX213CWI+T when its different low-power shutdown behavior is beneficial, after checking every control and receiver pin against the existing schematic. MAX211CWI and MAX211ECWI can serve as non-+T ordering options when the shipping format permits. For every candidate, confirm the exact driver and receiver enable states, shutdown timing, temperature limits, charge-pump capacitor connections, and lifecycle status in the manufacturer datasheet. Avoid selecting a cross-family interface solely by connector compatibility, because RS-232, RS-422, and RS-485 use incompatible voltage and signaling conventions.

代替品との比較

パラメータ この製品 MAX211ECWI+T MAX213CWI+T MAX211CWI MAX211ECWI MAX213ECWI+T
Package 28-SOIC 28-SOIC - same 28-SOIC - same 28-SOIC - same 28-SOIC - same 28-SOIC - same
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Supply Voltage +5 V +5 V +5 V +5 V +5 V +5 V
Shipping Format Suffix +T tape-and-reel format +T tape-and-reel format +T tape-and-reel format Non +T ordering option Non +T ordering option +T tape-and-reel format

主な差別化要因

  • Single-supply operation with four-driver and five-receiver integration (vs MAX211ECWI+T)
  • Established MAX211 function with more than 120kbps data-rate capability (vs MAX213CWI+T)
  • Four integrated external-capacitor charge-pump interface (vs MAX211CWI)

設計ノート

Place the four specified 0.1µF charge-pump capacitors close to the pins identified in the manufacturer datasheet. Keep their ground returns short and connect them to a quiet ground plane region rather than routing through the logic return path. The MAX211CWI+T uses a single +5V supply, so minimizing capacitor-loop area also reduces switching current in the charge-pump section and helps maintain stable driver output levels.

Keep the 28-pin wide SOIC close to the RS-232 connector and separate the charge-pump region from sensitive analog or high-speed digital traces. Route each driver and receiver signal according to the system ground-reference plan, and avoid sharing narrow return paths between the interface connector and unrelated loads. Review every connector pin against the manufacturer datasheet because legacy RS-232 equipment may use different signal names for the same connector positions.

Do not substitute an RS-422 or RS-485 interface solely because the connector shape is similar. The MAX211CWI+T produces bipolar ±5V EIA/TIA-232E signals, whereas differential interfaces use different voltage relationships and termination practices. Also verify shutdown polarity, enable timing, receiver enable state, cable length, and grounding before releasing the board for production.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The MAX211 is a commercial interface IC rather than an automotive-qualified device; specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed from current manufacturer product documentation.

データ検証日: 2026-11-09 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

MAX211CWI+T datasheet MAX211CWI+T pinout MAX211CWI+T datasheet pdf MAX211CWI+T schematic MAX211CWI+T equivalent MAX211CWI+T replacement MAX211CWI+T cross reference MAX211CWI+T vs MAX211ECWI+T MAX211CWI+T footprint MAX211CWI+T price MAX211CWI+T stock Analog Devices MAX211CWI+T MAX211 28-SOIC pinout MAX211CWI+T application circuit 4/5 RS-232 120kbps SOIC-28

関連部品&用語

Analog Devices Maxim Integrated MAX211CWI+T MAX211 MAX211ECWI+T MAX213CWI+T MAX211CWI MAX211ECWI MAX213ECWI+T RS-232 transceiver V.28 interface EIA/TIA-232E interface IC single-supply transceiver charge-pump voltage converter RS-232 driver RS-232 receiver TTL logic CMOS logic 28-pin wide SOIC surface-mount package 120kbps data rate 0.1µF capacitor digital communication
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示