MAX3488EESA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
部品番号: MAX3488EESA+T ✓ 生産中MAX3488EESA+T 概要
An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals and reconstructs logic-level data from received differential signals. Within the interface hierarchy, this device combines an RS-485/RS-422 line driver, a line receiver, ESD protection, and slew-rate control in one semiconductor package. It supports the physical layer used by industrial automation, building controls, instrumentation, and data-acquisition equipment.
The MAX3488EESA+T provides a 12 Mbps data rate, ±15 kV ESD-protected inputs, and a slew-rate-limited driver. The low-power 3.3 V design supports systems in which transceiver power must remain compatible with modern digital logic. One driver and one receiver per package make the device appropriate for half-duplex buses that share a physical cable pair, subject to the operating requirements of the selected network topology.
Slew-rate limitation reduces the high-frequency content of transmitted transitions, helping limit electromagnetic interference and reflections on cables that may not be perfectly terminated. The integrated ESD protection is a major system-level benefit for field-facing equipment because it strengthens the interface against electrostatic discharge encountered during installation, servicing, or connection of external cables.
Typical applications include industrial RS-485 control networks, building-automation equipment, factory data acquisition, remote instrumentation, and isolated or non-isolated industrial communication modules. In a multidrop bus, the designer must preserve the transceiver enable state during receive intervals, configure termination correctly, and verify that all connected nodes use compatible data rates and polarity.
For a new design, place the MAX3488EESA+T close to the connector and protection network, route the balanced pair as a tightly coupled differential pair, and provide local bypassing. Confirm that the board ground and cable shield strategy meet the grounding requirements of the industrial installation; the transceiver's ESD rating does not replace an external surge or lightning-protection design.
This product overview combines the manufacturer's interface description with drop-in family options, package guidance, application examples, and practical PCB considerations. It highlights the MAX3488EESA+T's 3.3 V supply, 12 Mbps speed, ±15 kV ESD protection, and 8-pin SOIC implementation to support faster component selection and first-pass hardware planning.
ドロップイン代替品: MAX3488EESA+T — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MAX3488EESA+T (同一形状・フットプリント) — 相違点: Package, Driver Count, Receiver Count, Supported Standards, Communication Mode.
MAX3488ECSA+
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX3488EESA+
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX3488EESA+T 仕様
| Product Type | RS-485/RS-422 transceiver |
| 電源電圧 | 3.3 V |
| Operating Supply Voltage Range | 3 V to 3.6 V |
| Maximum Data Rate | 12 Mbps |
| ESD Protection | ±15 kV |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Supported Standards | RS-485 and RS-422 |
| Driver Slew Rate | Slew-rate limited |
| Communication Mode | Half-duplex |
| パッケージ | 8-pin SOIC |
| 実装タイプ | Surface mount |
MAX3488EESA+T 8-pin soic ピン配置ガイド
MAX3488EESA+T (8-pin soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: MAX3488EESA+T.
詳細は データシート をご参照ください。
主な用途
MAX3488EESA+T の用途: 6 件s: Industrial RS-485 Control Networks, Building Automation and HVAC Equipment, Factory Data-Acquisition Modules, Remote Instrumentation, Communication Gateways, Security and Access-Control Panels.
Industrial RS-485 Control Networks
MAX3488EESA+T fits 3.3 V industrial control modules that exchange commands and status over a balanced RS-485 bus. Its 12 Mbps capability provides substantial margin for short factory links, while the slew-rate-limited driver helps reduce unwanted high-frequency energy and reflections. The ±15 kV ESD protection is valuable at cabinet and machine-edge connectors where cables may be connected during maintenance. A designer should still use a biasing network, establish the driver-enable protocol, and verify termination against the selected bus topology.
おすすめ
Building Automation and HVAC Equipment
The MAX3488EESA+T is appropriate for building-automation controllers, room modules, and HVAC equipment that use a 3.3 V controller and a wired RS-485 field bus. Its one-driver/one-receiver arrangement supports a shared cable pair, while the 12 Mbps rate comfortably exceeds the data rates normally required for environmental monitoring and actuator commands. Protect the external line through appropriate connector-side surge protection, maintain a consistent enable convention, and avoid leaving multiple transmitters active during receive windows.
おすすめ
Factory Data-Acquisition Modules
MAX3488EESA+T can connect a compact data-acquisition module to industrial sensors and controllers over a wired RS-485 network. The 3 V to 3.6 V operating range aligns with modern embedded control logic, and the 12 Mbps capability supports high burst rates without requiring a separate high-voltage transceiver. For reliable operation, separate logic and cable grounds according to the installation strategy, use a twisted differential pair, and apply termination only where the network topology requires it. External surge devices remain appropriate for cables exposed beyond the enclosure.
おすすめ
Remote Instrumentation
MAX3488EESA+T suits remote sensor and instrumentation nodes that need a compact, low-power balanced transceiver. The 3.3 V architecture simplifies integration with low-voltage processors, while one driver and one receiver support half-duplex operation over a single cable pair. The 12 Mbps rate gives designers flexibility across laboratory, agricultural, and environmental monitoring networks. Firmware should serialize access to the shared bus, and the hardware should include defined enable states and fault-safe behavior so a reset or disconnected controller does not block other nodes.
おすすめ
Communication Gateways
MAX3488EESA+T is useful in gateways that bridge a legacy RS-485 field network to a modern embedded Ethernet platform. Its 12 Mbps rate handles the field-side traffic required by common supervisory control and data-acquisition systems, while the 3.3 V supply simplifies integration with current-generation logic. A gateway must implement media access control, line biasing, termination, and controlled driver-enable timing. Keep the balanced trace pair away from switching-power nodes and use the manufacturer's recommended grounding arrangement when connecting the field cable.
おすすめ
Security and Access-Control Panels
MAX3488EESA+T can support access-control panels, door controllers, and security peripherals connected through a wired RS-485 or RS-422 network. Its ±15 kV ESD protection is useful at panel connectors, and the 3.3 V operation fits compact embedded control boards. Designers should separate the communications pair from security-sensitive analog circuitry, maintain defined logic states during reset, and use appropriate surge protection for cables that leave the controlled enclosure. For installations with long outdoor runs, an isolated transceiver architecture may provide additional galvanic protection.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MAX3488EESA+T — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX3488ECSA | MAX3488EESA |
|---|---|---|---|
| Manufacturer | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC - same package | 8-pin SOIC - same package |
| Product Type | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V |
| Maximum Data Rate | 12 Mbps | 12 Mbps | 12 Mbps |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV |
| Driver and Receiver Count | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver |
| Driver Configuration | Slew-rate limited | Slew-rate limited | Slew-rate limited |
主な差別化要因
- Maintains the MAX3488E electrical configuration in an 8-pin SOIC footprint (vs MAX3488ECSA)
- Provides the exact tape-and-reel order configuration identified by the target MPN (vs MAX3488EESA)
- Combines 12 Mbps operation with high-level integrated ESD protection (vs MAX3485EESA+T)
設計ノート
Route the RS-485/RS-422 pair as a tightly coupled differential pair with substantially equal trace lengths and a continuous ground reference beneath the pair. Place the MAX3488EESA+T close to the board connector or protection network to minimize the distance over which transient energy can couple into the transceiver. Keep switching-regulator paths and high-current return paths away from the balanced lines, and avoid adding ground-plane breaks beneath either conductor.
Do not enable the driver continuously on a half-duplex multidrop bus. Firmware and hardware must guarantee that only one transmitter is active at a time, while the receiver remains available when appropriate. Verify fail-safe output states during reset and power loss because multiple floating drivers could contend for the bus. Also confirm whether the design uses RS-485 or RS-422 wiring, because termination and grounding practices differ between point-to-point and multidrop networks.
The slew-rate-limited MAX3488EESA+T driver helps reduce high-frequency harmonics and ringing, but cable topology still determines EMI performance. Use the manufacturer's recommended termination and fail-safe biasing arrangement, and avoid placing long stubs on a multidrop bus. If a cable leaves an enclosure or crosses between buildings, add appropriately rated external surge and lightning protection; the integrated ±15 kV ESD capability is not a substitute for a complete cable-protection network.
Decouple the 3.3 V supply close to the device and follow the manufacturer datasheet for the required capacitor network and layout. Confirm that the supply remains within 3 V to 3.6 V during startup, load changes, and disturbance on an industrial bus. Evaluate driver current and cable loading against the transceiver's output-current limit, and ensure that any protection device does not add excessive capacitance or disturb the intended edge rate.
コンプライアンス情報
The manufacturer product-page summary identifies MAX3488E as a production device but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. No automotive qualification designation is stated.