MAX364ESE+ - 85Ω Quad SPST Analog Switch | Analog Devices
部品番号: MAX364ESE+ ✓ 生産中MAX364ESE+ 概要
An analog switch is an electronic routing component that connects or disconnects analog signals under digital control. A SPST switch provides one conducting path, while the MAX364's normally closed configuration connects each signal path when its control input is inactive. Within the broader semiconductor hierarchy, this device is an analog switch, then a switch IC and interface IC. It is intended to bridge low-frequency or precision analog signals without using a mechanical relay.
The MAX364 provides four independent normally closed channels, low on-resistance below 85Ω, on-resistance matching within 2Ω between channels, and on-resistance variation of no more than 9Ω across the analog signal range. These characteristics help limit insertion-error differences between channels. The equalized resistance also supports reproducible measurements when several switched nodes participate in the same precision measurement path.
Each MAX364/MAX365 family member uses the same precision switch architecture, but the MAX364 has four normally closed switches while the MAX365 has four normally open switches. The MAX364ESE+ suffix identifies the narrow 16-SOIC configuration. Its four control inputs allow independent routing of four analog nodes, making it practical for scanning, signal isolation, sample-and-hold interfaces, and programmable test systems.
Typical applications include precision multimeter input switching, automated test equipment, data-acquisition systems, instrumentation signal routing, and analog measurement front ends. In each case, the normally closed state can preserve signal continuity during reset or control-signal absence. The matched low on-resistance also reduces channel-dependent errors when the same source drives different measurement paths.
For layout, route high-impedance signals directly to the switch pins and keep the analog traces short and away from fast digital or switching nodes. Check the control-logic levels and supply conditions in the manufacturer datasheet before designing the driver. Treat the 85Ω on-resistance as part of the complete source impedance rather than as an isolated component value, because series source resistance and switch resistance combine to determine signal attenuation.
ドロップイン代替品: MAX364ESE+ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
MAX364CSE+
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MAX364ESE+ 最大定格&電気的特性
| Number of Switches | 4 circuits |
| Switch Configuration | 1:1 |
| Switch Type | Quad SPST |
| Default State | Normally closed (NC) |
| Maximum On-Resistance | 85 ohm |
| On-Resistance Matching Between Channels | Within 2 ohm |
| Maximum On-Resistance Variation | 9 ohm over the analog signal range |
| パッケージ | 16-pin narrow SOIC |
| 実装タイプ | Surface mount |
| ピン数 | 16 pins |
| Control Inputs | 4 control inputs |
MAX364ESE+ 16-pin narrow soic ピン配置ガイド
MAX364ESE+ (16-pin narrow soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: MAX364ESE+.
詳細は データシート をご参照ください。
主な用途
MAX364ESE+ の用途: 6 件s: Precision Multimeter Input Switching, Automated Test Equipment Signal Routing, Data Acquisition Channel Isolation, Instrument Signal Routing, Programmable Sensor Interface, Analog Loopback and Diagnostic Circuits.
Precision Multimeter Input Switching
The MAX364ESE+ fits precision multimeter input routing because its four normally closed channels provide less than 85Ω on-resistance, matching within 2Ω between channels, and no more than 9Ω variation across the analog signal range. Each channel can connect a measurement source to the meter input, while the NC state preserves continuity when the control signal is inactive. Keeping channel resistance differences small helps reduce measurement gain error. The complete error budget should also include switch leakage, source impedance, ADC or meter input impedance, and settling time.
おすすめ
Automated Test Equipment Signal Routing
The MAX364ESE+ is suitable for automated test equipment that routes several low-frequency or precision analog nodes through a compact, controlled interface. Four independent SPST paths reduce the number of separate relay or switch assemblies, while matching within 2Ω helps maintain similar signal attenuation across test channels. The 85Ω maximum must be included in the impedance budget for high-impedance sources. Place the device close to the tester interface and use short analog routing to minimize additional parasitic capacitance.
おすすめ
Data Acquisition Channel Isolation
The MAX364ESE+ can isolate four channels in a data-acquisition front end while maintaining normally closed signal paths. Its specified channel matching within 2Ω and resistance variation of no more than 9Ω reduce channel-dependent errors when the same source is sampled through different routes. The 85Ω on-resistance contributes to source impedance and may interact with the acquisition converter's acquisition time. Verify settling requirements, input leakage, and the complete signal range against the manufacturer datasheet before selecting capacitor and sampling parameters.
おすすめ
Instrument Signal Routing
The MAX364ESE+ provides a compact way to route four precision analog signals within laboratory and industrial instrumentation. The normally closed configuration allows a selected path to remain connected until the corresponding control input overrides it. Consistent on-resistance below 85Ω helps maintain predictable attenuation, while the 2Ω channel matching supports repeatable comparisons between measurement paths. High-impedance nodes should be routed with short traces, guarded where appropriate, and kept away from switching or digital timing signals.
おすすめ
Programmable Sensor Interface
The MAX364ESE+ can connect or disconnect sensor lines in a programmable analog interface when low-frequency operation and a 16-pin surface-mount footprint are suitable. Its normally closed paths provide continuity during reset, while four control inputs allow individual sensor channels to be selected. The switch's maximum 85Ω on-resistance must be checked against sensor loading, transducer impedance, and downstream amplifier biasing. For source impedances much greater than 85Ω, the switch may contribute little error; for lower-impedance nodes, its resistance should be included directly.
おすすめ
Analog Loopback and Diagnostic Circuits
The MAX364ESE+ is useful in analog loopback and diagnostic circuitry because four independent channels can form or interrupt test paths under digital control. Matched on-resistance within 2Ω helps compare channel paths, and the flatness limit of 9Ω reduces resistance-driven variation over the specified analog signal range. The normally closed topology can support fail-safe continuity paths when the controller is inactive. Confirm control polarity, inactive-state voltage, and maximum switch voltage using the MAX364 manufacturer datasheet before implementing diagnostic loops.
おすすめ
エンジニアリング参考データ: MAX364ESE+ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX364CSE+ |
|---|---|---|
| Package | 16-pin narrow SOIC | 16-pin narrow SOIC |
| Brand | Analog Devices | Analog Devices |
| Number of Switches | 4 circuits | 4 circuits |
| Switch Type | Quad SPST | Quad SPST |
| Default State | Normally closed | Normally closed |
| Maximum On-Resistance | 85 ohm | 85 ohm |
| On-Resistance Matching | Within 2 ohm | Within 2 ohm |
| On-Resistance Variation | 9 ohm maximum | 9 ohm maximum |
主な差別化要因
- Four matched normally closed channels (vs MAX364CSE+)
- Defined precision resistance characteristics (vs MAX365ESE+)
- Compact four-channel integration (vs Mechanical relay alternatives)
設計ノート
Include the maximum 85Ω on-resistance in the complete source-impedance calculation. For a voltage divider formed by the source impedance and the receiving input, use the actual switch resistance rather than assuming an ideal connection. This is especially important when the receiving circuit has high input impedance, because leakage and parasitic capacitance can then dominate errors that are not visible from resistance matching alone.
Route each analog path directly to its MAX364ESE+ pin and avoid sharing narrow segments between channels that need independent measurements. Keep the 16-pin SOIC away from clock, pulse, and high-current switching traces. For high-impedance nodes, use guarded spacing where practical and minimize exposed PCB area; otherwise leakage and surface contamination can exceed the useful precision of the matched on-resistance characteristic.
Do not treat MAX365ESE+ as a direct substitute because it uses normally open switches rather than the MAX364ESE+'s normally closed paths. Also verify the control polarity, inactive control-state voltage, and absolute maximum analog voltage before connecting external circuitry. A valid drop-in replacement must preserve the 16-pin SOIC footprint, four-channel NC behavior, and the relevant electrical limits.
コンプライアンス情報
The '+' ordering suffix commonly denotes a lead-free finish, but the exact RoHS, REACH, halogen-free, and conflict-minerals status was not established from the listed technical sources.