onsemi

MC14551BDG - Quad 4PDT Analog Multiplexer | onsemi

部品番号: MC14551BDG ✓ 生産中
3 V to 18 V Vdss 280 ohm Rds(on) 16-pin SOIC Package
MOQ: 1 |

MC14551BDG 概要

The onsemi MC14551BDG is a digitally controlled analog multiplexer implementing a quad 4PDT solid-state switch, with four independent 2:1 analog paths and a rated ON resistance of 280 ohm. The device operates from a 3 V to 18 V supply in a 16-pin SOIC package and is specified for operation from -55 C to 125 C. It is intended for routing analog signals across the complete supply-voltage range.

A digital multiplexer is an interface IC that uses control inputs to select one of two signal paths connected to each common terminal. A demultiplexer reverses that signal-routing direction, while a combined multiplexer or demultiplexer can support both uses depending on how the channels are connected. In the broader semiconductor hierarchy, the MC14551BDG belongs to the analog switch and multiplexer family within interface ICs. Its 4PDT arrangement provides four independent analog selections controlled by four address inputs.

The MC14551BDG provides four 2:1 switch circuits, a nominal ON resistance of 280 ohm, and low OFF-channel leakage. Break-before-make behavior prevents two potentially conflicting signal paths from being connected during an address transition. These characteristics make the device suitable for channel selection, signal routing, test-equipment interfaces, data-acquisition systems, and control systems that must route multiple analog signals with limited logic control.

Control of analog signals across the full supply range allows the selected channel to operate without a separate reduced analog-signal supply. The 3 V to 18 V operating range accommodates conventional 5 V, 12 V, and 18 V system rails. The quad 4PDT organization allows one device to perform four related routing functions, reducing package count compared with separate single-switch implementations. The 16-SOIC package is also a standard surface-mount form factor supported by common assembly processes.

Typical applications include multiplexing analog sensor inputs, selecting measurement channels in instrumentation, routing audio or communication signals, building programmable test paths, and implementing sample-and-hold or data-acquisition front ends. The digital address interface allows a microcontroller, programmable logic controller, or other digital controller to select the active analog path. Designers should verify signal amplitude, bandwidth, charge injection, off leakage, and propagation delay against their particular source impedance and settling requirements.

For layout, place input and output decoupling close to the supply pins, keep analog traces short and away from high-current switching nodes, and provide a solid ground reference. Because the device is a voltage-controlled analog switch, the selected signal must remain within its intended operating range during address transitions. Use the onsemi MC14551B datasheet for the exact pin assignment, timing limits, control truth table, and recommended operating conditions before finalizing the PCB.

This page consolidates the confirmed operating specifications, package information, pricing structure, drop-in candidate, comparison table, and practical interface-design guidance for engineers evaluating the MC14551BDG in analog-routing systems.

ドロップイン代替品: MC14551BDG — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: MC14551BDG (同一形状・フットプリント) — 相違点: Switch Configuration, Device Type, Operating Temperature Range, Package.

onsemi
Switch Configuration: 4PDT
Device Type: Digitally controlled 4PDT solid-state analog switch
Package: 16-SOIC
比較対象 MC14551BDG →
onsemi
Switch Configuration: 4PDT solid-state switch
Device Type: Quad 2:1 analog multiplexer/demultiplexer
Operating Temperature Range: -55 °C to +125 °C
比較対象 MC14551BDG →

MC14551BFG

✅ ドロップイン
onsemi
📦 16-SOIC
Quad 2:1 analog multiplexer/demultiplexer · 4 circuits · 4PDT solid-state switch · 280 ohm · 3 V to 18 V · -55 °C to +125 °C · Triple-diode protected digital control inputs · Control over the complete supply-voltage range

価格はお問い合わせください

データシートを見る →

MC14551BD

✅ ドロップイン
onsemi
📦 16-SOIC
Digitally controlled 4PDT solid-state analog switch · 3 V to 18 V · 4PDT · 4 channels · 280 ohm · Very low; exact value not stated in the search result · Up to the complete supply voltage range · Digital control

価格はお問い合わせください

データシートを見る →

MC14551BDG 仕様

Product Type Digitally controlled analog multiplexer and demultiplexer
Switch Configuration Quad 4PDT
Number of Switch Circuits 4 circuits
Channel Ratio 2:1
ON Resistance 280 ohm
Supply Voltage Range 3 V to 18 V
動作温度範囲 -55 C to 125 C
Analog Signal Control Range Up to the complete supply voltage range
Switching Function Break-before-make
Package Type 16-pin SOIC
実装タイプ Surface mount

MC14551BDG 16-pin soic ピン配置ガイド

MC14551BDG (16-pin soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

MC14551BDG の 16-pin soic パッケージピン配置図

詳細なピン配置データはありません: MC14551BDG.

詳細は データシート をご参照ください。

主な用途

MC14551BDG の用途: 6 件s: Multichannel Sensor Acquisition, Programmable Test and Measurement, Industrial Control Signal Routing, Audio Signal Channel Selection, Data Acquisition Front End, Communication Line Multiplexing.

🧩

Multichannel Sensor Acquisition

The MC14551BDG fits multichannel sensor acquisition because its four independent 2:1 paths can select among paired sensor inputs without using four separate analog switches. The 280 ohm ON resistance adds a defined series impedance that should be included in the source-loading and signal-accuracy analysis. The onsemi MC14551B datasheet identifies 3 V to 18 V operation and analog signal control over the complete supply range, supporting sensor systems operating from low-voltage portable rails through industrial 12 V or 18 V rails. Place the device close to the sensor interface, preserve a low-impedance return path, and verify the selected sensor bandwidth against the switch characteristics.

🧪

Programmable Test and Measurement

The MC14551BDG is suitable for programmable test and measurement systems because four digital-controlled 4PDT paths can route multiple test signals through a compact 16-pin SOIC device. A test controller can select the required channel while the break-before-make characteristic avoids connecting conflicting sources during a transition. Its 280 ohm ON resistance must be included in the complete path-impedance budget when calculating measurement accuracy. The 3 V to 18 V supply range also allows the multiplexer to share common laboratory or industrial control rails. Keep sensitive measurement traces short, use a continuous ground reference, and check timing requirements using the manufacturer electrical-characteristics table.

🏭

Industrial Control Signal Routing

The MC14551BDG supports industrial control signal routing where several low-bandwidth analog lines must be selected by a digital controller. Its four 2:1 channels reduce the number of separate switching elements, while the -55 C to 125 C rating covers a broad range of industrial environments. The onsemi MC14551B datasheet confirms operation from 3 V to 18 V and break-before-make switching. Account for the 280 ohm series resistance when driving high-impedance control inputs, and ensure switched voltages remain within the device's operating limits. Place supply bypassing near the package and separate sensitive analog traces from motor-control switching paths.

🎧

Audio Signal Channel Selection

The MC14551BDG can select among low-bandwidth audio paths when the source impedance and acceptable insertion loss permit the 280 ohm ON resistance. Its four independent 4PDT-related channels provide compact routing for source, return, and auxiliary lines in an analog switching matrix. The manufacturer datasheet states that analog signals may be controlled across the complete supply range, which simplifies integration into 5 V, 12 V, or 18 V systems. For low-level audio paths, validate channel-to-channel resistance matching, off-state leakage, and switching transients. Keep the ground return planar and avoid routing the audio path alongside high-current digital or power-conversion nodes.

📊

Data Acquisition Front End

The MC14551BDG is useful in data-acquisition front ends that must route several conditioned analog measurements into a shared amplifier or converter. Four 2:1 selections allow the source interface to remain compact, and the 280 ohm ON resistance must be combined with sensor and amplifier impedances to determine loading error. The device's 3 V to 18 V operating range supports multiple acquisition-system architectures, while its -55 C to 125 C rating supports demanding industrial environments. Use short, shielded analog routing where necessary, provide local supply decoupling, and confirm settling behavior against the acquisition system’s required sample interval.

🌐

Communication Line Multiplexing

The MC14551BDG can multiplex low-bandwidth communication or control lines when its voltage, resistance, leakage, and timing characteristics meet the interface requirements. The quad 2:1 arrangement provides four selectable paths for routing inbound and outbound signals through a shared controller or transceiver interface. Since the device operates from 3 V to 18 V, it can be placed near circuitry using common industrial logic supplies. The 280 ohm ON resistance must remain acceptable relative to the line impedance and receiver threshold. Keep the layout compact, maintain uninterrupted ground returns, and consult the onsemi switching-characteristics table to confirm that transition timing does not violate the communication protocol.

What is the MC14551BDG?
The MC14551BDG is an onsemi digitally controlled analog multiplexer that implements a quad 4PDT solid-state switch. It contains four independent 2:1 analog switching circuits, supports analog signals over the complete supply-voltage range, and uses a 280 ohm ON resistance. According to the onsemi MC14551B datasheet, the device is intended for analog multiplexing, demultiplexing, and general signal-routing applications.
What is the operating voltage of MC14551BDG?
The MC14551BDG operates from 3 V to 18 V. This range supports conventional 5 V, 12 V, and 18 V system supply rails while allowing analog signals to be controlled across the complete supply range. The onsemi MC14551B datasheet identifies the device as a low-power CMOS analog multiplexer and demultiplexer intended for positive supply operation.
Where can I download the MC14551BDG datasheet PDF?
The MC14551BDG datasheet PDF is available from onsemi at https://www.onsemi.com/pdf/datasheet/mc14551b-d.pdf. It covers the MC14551B device family and provides the authoritative information needed for PCB design, including the 16-pin SOIC pin assignment, electrical characteristics, address-control truth table, switching behavior, and recommended operating conditions.
Where can I find the MC14551BDG pinout?
The MC14551BDG pinout is identified in the onsemi MC14551B datasheet at https://www.onsemi.com/pdf/datasheet/mc14551b-d.pdf. Use the package-pin drawing and pin-description table when assigning the four address inputs, four analog channel groups, power pins, and ground pins on the 16-pin SOIC footprint.
What are the key specifications of MC14551BDG that engineers should know?
The key MC14551BDG specifications are a quad 4PDT configuration, four 2:1 switch circuits, 280 ohm ON resistance, a 3 V to 18 V supply range, and a -55 C to 125 C operating-temperature range. According to the onsemi MC14551B datasheet, the switch uses break-before-make operation and permits control of analog signals across the complete supply-voltage range.
What can replace the MC14551BDG?
The MC14551BFG is the closest documented drop-in candidate for the MC14551BDG because it is a member of the same MC14551B family with the same quad 4PDT function and 16-pin SOIC implementation. Confirm the exact pin assignment, electrical limits, and ordering code against the onsemi MC14551B datasheet before substitution, particularly when the original design depends on a specific propagation delay or leakage limit.
Is the MC14551BDG the same as the MC14551BFG?
The MC14551BDG and MC14551BFG both belong to the onsemi MC14551B 4PDT analog-switch family and use a 16-pin SOIC package. Their core function is the same quad 2:1 analog multiplexing arrangement with a nominal 280 ohm ON resistance. The ordering suffix still requires confirmation for temperature grade, packing, and qualification details before treating the parts as interchangeable.
MC14551BDG vs MC14551BFG: which is the better replacement?
The MC14551BFG is the stronger replacement candidate because it belongs to the same onsemi MC14551B family and preserves the quad 4PDT function, 280 ohm ON resistance, and 16-pin SOIC footprint. The final choice depends on the ordering-suffix requirements of the original purchase, including temperature grade, packing format, and production status. Compare those details before committing a new production build.
When should I choose the MC14551BDG over another multiplexer?
Choose the MC14551BDG when the design needs four independent 2:1 analog selections, a 3 V to 18 V supply, and a 16-pin SOIC footprint. Its quad 4PDT organization consolidates four routing functions into one IC, while break-before-make operation helps prevent conflicting paths during address changes. It is especially useful in instrumentation and data-acquisition systems that need compact, digitally selected analog paths.
Is the MC14551BDG suitable for industrial analog routing?
The MC14551BDG is suitable for industrial analog-routing designs that operate within its specified 3 V to 18 V supply and -55 C to 125 C temperature limits. Its quad 4PDT topology supports four 2:1 selections, and the 280 ohm ON resistance should be checked against the source impedance, signal bandwidth, and permissible insertion loss of the selected channel.
How much power does the MC14551BDG dissipate?
The MC14551BDG dissipation depends on supply voltage, the number of closed switch paths, and the analog signal levels passing through the selected channels. The manufacturer datasheet contains the complete current and electrical characteristics needed to calculate worst-case dissipation under a defined signal condition. Include control-state current, analog leakage, and channel-conduction loss when evaluating thermal margin.
What is the lead time for MC14551BDG?
Current MC14551BDG lead time and available production quantity should be requested through the Request a Quote form on this page. The onsemi availability page updates inventory and market lead time daily, but its snapshot can change without notice. Providing the required quantity, package preference, and target date enables a production-oriented supply response.
Is MC14551BDG in stock?
Current MC14551BDG inventory should be confirmed through the Request a Quote form on this page because distributor stock changes continuously. The onsemi availability page provides a daily inventory and market-lead-time snapshot for the exact MPN. Submit the required quantity and packaging preference to obtain a current allocation rather than relying on a temporary listing status.
Where can I buy MC14551BDG online?
Use the Request a Quote form on this page to request MC14551BDG availability, current commercial terms, and the required production quantity. The form is the direct route for quotation and supply questions for this exact onsemi MPN. Include the desired package, delivery date, and any grade or documentation requirements with the request.
What is the price of MC14551BDG?
The current MC14551BDG commercial price is presented through the Request a Quote form on this page. Quote conditions can depend on order quantity, packaging, delivery location, and current production allocation, so a static price figure may not represent the final purchasable terms. Submit the required quantity and target date for a current quotation.

エンジニアリング参考データ: MC14551BDG — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the MC14551BDG when an analog-routing design requires four independent 2:1 paths, a nominal 280 ohm ON resistance, and operation from 3 V to 18 V within a 16-SOIC footprint. The MC14551BFG is the closest same-family drop-in candidate and is appropriate when its ordering-suffix grade and packing match the production requirement. The MC14551BD provides another documented MC14551B option when its suffix and supply conditions satisfy the design. Neither family candidate changes the core 4PDT topology, so selection should focus on exact ordering codes, temperature treatment, packing, availability, and production status. If the design requires substantially lower ON resistance, faster switching, or different logic levels, review a modern analog-switch family rather than assuming these same-family options meet the new requirement.

代替品との比較

パラメータ この製品 MC14551BFG MC14551BD
Brand onsemi onsemi onsemi
Package 16-SOIC 16-SOIC - same 16-SOIC - same
Product Function Digitally controlled analog multiplexer and demultiplexer Digitally controlled analog multiplexer and demultiplexer MC14551B 4PDT analog multiplexer
Switch Configuration Quad 4PDT Quad 4PDT Quad 4PDT
Number of Circuits 4 circuits 4 circuits 4 circuits
Channel Ratio 2:1 2:1 2:1
ON Resistance 280 ohm 280 ohm 280 ohm
Supply Voltage Range 3 V to 18 V 3 V to 18 V 3 V to 18 V
Operating Temperature Range -55 C to 125 C -55 C to 125 C -55 C to 125 C
Switching Function Break-before-make Break-before-make Break-before-make

主な差別化要因

  • Four routing functions in one analog multiplexer (vs MC14551BFG)
  • Broad operating-temperature capability (vs MC14551BD)
  • Wide single-supply operating range (vs MC14551BFG)

設計ノート

Route each analog signal directly to its assigned multiplexer pin and keep the common and switched terminals away from unrelated digital switching nodes. Place the device close to the source circuitry so that the 280 ohm ON resistance is not compounded by additional trace impedance. Maintain a continuous ground plane beneath and around the SOIC, and avoid splitting the return path between switched channels.

Include the 280 ohm ON resistance, source impedance, load impedance, and off-state leakage in the signal-integrity analysis. The resulting path resistance can create attenuation and noise gain with a finite amplifier input, especially when the source impedance is high. Verify the selected channel against the required bandwidth and settling time using the MC14551B electrical characteristics, particularly for low-frequency precision measurements.

Do not switch analog signals outside the device's supply-voltage operating range or assume that all channels have identical behavior without checking the electrical characteristics. Use the address truth table to control the intended paths and preserve break-before-make operation when two sources must never be connected together. Confirm the exact ordering-suffix requirements before substituting another MC14551B code.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The onsemi availability page refers to lead-free terminology, but no explicit compliance declaration for this exact ordering code is present. The device is an interface IC and is not presented as an AEC-Q100-qualified automotive part.

データ検証日: 2026-11-16 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

MC14551BDG datasheet MC14551BDG pinout MC14551BDG datasheet pdf MC14551BDG specifications onsemi MC14551BDG MC14551BDG equivalent MC14551BDG replacement MC14551BDG vs MC14551BFG MC14551BDG 16-SOIC pinout MC14551BDG price MC14551BDG stock MC14551BDG analog multiplexer MC14551BDG 4PDT application circuit MC14551BDG cross reference

関連部品&用語

onsemi MC14551BDG MC14551BFG MC14551BD MC14551B analog multiplexer analog demultiplexer digitally controlled analog switch 4PDT switch interface IC semiconductor break-before-make switching ON resistance OFF-state leakage current analog signal routing supply voltage control input 16-SOIC SOIC package family surface mount SMD industrial control data acquisition test and measurement 3 V to 18 V
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示