MC14551BDG - Quad 4PDT Analog Multiplexer | onsemi
MPN: MC14551BDG ✓ 啟用中MC14551BDG 概覽
A digital multiplexer is an interface IC that uses control inputs to select one of two signal paths connected to each common terminal. A demultiplexer reverses that signal-routing direction, while a combined multiplexer or demultiplexer can support both uses depending on how the channels are connected. In the broader semiconductor hierarchy, the MC14551BDG belongs to the analog switch and multiplexer family within interface ICs. Its 4PDT arrangement provides four independent analog selections controlled by four address inputs.
The MC14551BDG provides four 2:1 switch circuits, a nominal ON resistance of 280 ohm, and low OFF-channel leakage. Break-before-make behavior prevents two potentially conflicting signal paths from being connected during an address transition. These characteristics make the device suitable for channel selection, signal routing, test-equipment interfaces, data-acquisition systems, and control systems that must route multiple analog signals with limited logic control.
Control of analog signals across the full supply range allows the selected channel to operate without a separate reduced analog-signal supply. The 3 V to 18 V operating range accommodates conventional 5 V, 12 V, and 18 V system rails. The quad 4PDT organization allows one device to perform four related routing functions, reducing package count compared with separate single-switch implementations. The 16-SOIC package is also a standard surface-mount form factor supported by common assembly processes.
Typical applications include multiplexing analog sensor inputs, selecting measurement channels in instrumentation, routing audio or communication signals, building programmable test paths, and implementing sample-and-hold or data-acquisition front ends. The digital address interface allows a microcontroller, programmable logic controller, or other digital controller to select the active analog path. Designers should verify signal amplitude, bandwidth, charge injection, off leakage, and propagation delay against their particular source impedance and settling requirements.
For layout, place input and output decoupling close to the supply pins, keep analog traces short and away from high-current switching nodes, and provide a solid ground reference. Because the device is a voltage-controlled analog switch, the selected signal must remain within its intended operating range during address transitions. Use the onsemi MC14551B datasheet for the exact pin assignment, timing limits, control truth table, and recommended operating conditions before finalizing the PCB.
This page consolidates the confirmed operating specifications, package information, pricing structure, drop-in candidate, comparison table, and practical interface-design guidance for engineers evaluating the MC14551BDG in analog-routing systems.
直接替換替代品,適用於 MC14551BDG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MC14551BDG (相同外形與佔位) — 差異在於 Switch Configuration, Device Type, Operating Temperature Range, Package.
MC14551BFG
✅ 直接替換聯絡詢價
查看資料表 →MC14551BDG 規格
| Product Type | Digitally controlled analog multiplexer and demultiplexer |
| Switch Configuration | Quad 4PDT |
| Number of Switch Circuits | 4 circuits |
| Channel Ratio | 2:1 |
| ON Resistance | 280 ohm |
| Supply Voltage Range | 3 V to 18 V |
| 工作溫度範圍 | -55 C to 125 C |
| Analog Signal Control Range | Up to the complete supply voltage range |
| Switching Function | Break-before-make |
| Package Type | 16-pin SOIC |
| 安裝類型 | Surface mount |
MC14551BDG 16-pin soic 腳位配置指南
MC14551BDG(16-pin soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MC14551BDG.
請參閱 資料表 以查看完整腳位配置。
典型應用
MC14551BDG 適用於 6 應用s: Multichannel Sensor Acquisition, Programmable Test and Measurement, Industrial Control Signal Routing, Audio Signal Channel Selection, Data Acquisition Front End, Communication Line Multiplexing.
Multichannel Sensor Acquisition
The MC14551BDG fits multichannel sensor acquisition because its four independent 2:1 paths can select among paired sensor inputs without using four separate analog switches. The 280 ohm ON resistance adds a defined series impedance that should be included in the source-loading and signal-accuracy analysis. The onsemi MC14551B datasheet identifies 3 V to 18 V operation and analog signal control over the complete supply range, supporting sensor systems operating from low-voltage portable rails through industrial 12 V or 18 V rails. Place the device close to the sensor interface, preserve a low-impedance return path, and verify the selected sensor bandwidth against the switch characteristics.
推薦
Programmable Test and Measurement
The MC14551BDG is suitable for programmable test and measurement systems because four digital-controlled 4PDT paths can route multiple test signals through a compact 16-pin SOIC device. A test controller can select the required channel while the break-before-make characteristic avoids connecting conflicting sources during a transition. Its 280 ohm ON resistance must be included in the complete path-impedance budget when calculating measurement accuracy. The 3 V to 18 V supply range also allows the multiplexer to share common laboratory or industrial control rails. Keep sensitive measurement traces short, use a continuous ground reference, and check timing requirements using the manufacturer electrical-characteristics table.
推薦
Industrial Control Signal Routing
The MC14551BDG supports industrial control signal routing where several low-bandwidth analog lines must be selected by a digital controller. Its four 2:1 channels reduce the number of separate switching elements, while the -55 C to 125 C rating covers a broad range of industrial environments. The onsemi MC14551B datasheet confirms operation from 3 V to 18 V and break-before-make switching. Account for the 280 ohm series resistance when driving high-impedance control inputs, and ensure switched voltages remain within the device's operating limits. Place supply bypassing near the package and separate sensitive analog traces from motor-control switching paths.
推薦
Audio Signal Channel Selection
The MC14551BDG can select among low-bandwidth audio paths when the source impedance and acceptable insertion loss permit the 280 ohm ON resistance. Its four independent 4PDT-related channels provide compact routing for source, return, and auxiliary lines in an analog switching matrix. The manufacturer datasheet states that analog signals may be controlled across the complete supply range, which simplifies integration into 5 V, 12 V, or 18 V systems. For low-level audio paths, validate channel-to-channel resistance matching, off-state leakage, and switching transients. Keep the ground return planar and avoid routing the audio path alongside high-current digital or power-conversion nodes.
推薦
Data Acquisition Front End
The MC14551BDG is useful in data-acquisition front ends that must route several conditioned analog measurements into a shared amplifier or converter. Four 2:1 selections allow the source interface to remain compact, and the 280 ohm ON resistance must be combined with sensor and amplifier impedances to determine loading error. The device's 3 V to 18 V operating range supports multiple acquisition-system architectures, while its -55 C to 125 C rating supports demanding industrial environments. Use short, shielded analog routing where necessary, provide local supply decoupling, and confirm settling behavior against the acquisition system’s required sample interval.
推薦
Communication Line Multiplexing
The MC14551BDG can multiplex low-bandwidth communication or control lines when its voltage, resistance, leakage, and timing characteristics meet the interface requirements. The quad 2:1 arrangement provides four selectable paths for routing inbound and outbound signals through a shared controller or transceiver interface. Since the device operates from 3 V to 18 V, it can be placed near circuitry using common industrial logic supplies. The 280 ohm ON resistance must remain acceptable relative to the line impedance and receiver threshold. Keep the layout compact, maintain uninterrupted ground returns, and consult the onsemi switching-characteristics table to confirm that transition timing does not violate the communication protocol.
推薦
推薦產品摘要
工程參考資料,適用於 MC14551BDG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MC14551BFG | MC14551BD |
|---|---|---|---|
| Brand | onsemi | onsemi | onsemi |
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same |
| Product Function | Digitally controlled analog multiplexer and demultiplexer | Digitally controlled analog multiplexer and demultiplexer | MC14551B 4PDT analog multiplexer |
| Switch Configuration | Quad 4PDT | Quad 4PDT | Quad 4PDT |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits |
| Channel Ratio | 2:1 | 2:1 | 2:1 |
| ON Resistance | 280 ohm | 280 ohm | 280 ohm |
| Supply Voltage Range | 3 V to 18 V | 3 V to 18 V | 3 V to 18 V |
| Operating Temperature Range | -55 C to 125 C | -55 C to 125 C | -55 C to 125 C |
| Switching Function | Break-before-make | Break-before-make | Break-before-make |
主要差異化特點
- Four routing functions in one analog multiplexer (對比MC14551BFG)
- Broad operating-temperature capability (對比MC14551BD)
- Wide single-supply operating range (對比MC14551BFG)
設計說明
Route each analog signal directly to its assigned multiplexer pin and keep the common and switched terminals away from unrelated digital switching nodes. Place the device close to the source circuitry so that the 280 ohm ON resistance is not compounded by additional trace impedance. Maintain a continuous ground plane beneath and around the SOIC, and avoid splitting the return path between switched channels.
Include the 280 ohm ON resistance, source impedance, load impedance, and off-state leakage in the signal-integrity analysis. The resulting path resistance can create attenuation and noise gain with a finite amplifier input, especially when the source impedance is high. Verify the selected channel against the required bandwidth and settling time using the MC14551B electrical characteristics, particularly for low-frequency precision measurements.
Do not switch analog signals outside the device's supply-voltage operating range or assume that all channels have identical behavior without checking the electrical characteristics. Use the address truth table to control the intended paths and preserve break-before-make operation when two sources must never be connected together. Confirm the exact ordering-suffix requirements before substituting another MC14551B code.
合規資訊
The onsemi availability page refers to lead-free terminology, but no explicit compliance declaration for this exact ordering code is present. The device is an interface IC and is not presented as an AEC-Q100-qualified automotive part.