onsemi

MC3303DR2 - Quad 3-36V Low-Noise Op Amp | onsemi

部品番号: MC3303DR2 ✓ 生産中
3 V to 36 V Vdss 14-pin SOIC Package
MOQ: 1 |

MC3303DR2 概要

onsemi MC3303DR2 is a single-supply, general-purpose quad operational amplifier with four amplifier circuits in a 14-pin SOIC package. Its 3 V to 36 V operating supply range and 8 mV differential input offset voltage make it suitable for industrial instrumentation, low-level signal conditioning, sensor interfaces, and general analog control systems. The device is designed as a low-noise alternative for applications requiring four amplifiers in one package.

An operational amplifier is an active analog component that compares two input voltages and amplifies their difference. A quad operational amplifier combines four amplifiers in one integrated circuit, reducing component count and simplifying PCB layout compared with four separate single amplifiers. This MC3303 device belongs to the operational-amplifier hierarchy: quad op amp, instrumentation amplifier stage, analog signal-conditioning IC, and semiconductor.

The MC3303DR2 provides four independent general-purpose amplifier channels, a 3 V to 36 V single-supply operating range, and an 8 mV differential input offset voltage rating. Its low-noise characterization makes it relevant to sensor signals, current-loop interfaces, transducer conditioning, and low-level control paths where the signal must be amplified without adding excessive circuit noise.

Operation from a single supply simplifies power-system design because the amplifier can operate with a positive supply and ground reference without requiring a symmetrical positive and negative rail. Designers must still observe the common-mode input range and output swing limitations of each amplifier channel. Decoupling close to the supply pins helps control supply ripple, while resistor selection and input-bias-current compensation determine practical DC offset behavior.

Typical applications include industrial sensor conditioning, four-channel process monitoring, general-purpose buffer stages, transimpedance front ends, active filtering, audio and communication interfaces, and control-loop amplifiers. Using four channels in one package can also reduce board area, although each channel still requires its own feedback network and output-load assessment.

The principal design consideration is ensuring that signal amplitudes remain within the amplifier's input common-mode range and output voltage swing across the complete 3 V to 36 V supply range. Check the manufacturer datasheet for the exact common-mode range, output-swing limits, input-bias current, slew rate, and stability requirements before finalizing high-gain or capacitive-load layouts.

This product page combines the exact MC3303DR2 identification, package information, electrical characteristics, drop-in alternatives, application guidance, and design checks needed for engineering evaluation. It also distinguishes verified drop-in candidates from options that require a separate pinout, electrical, and qualification review before use in a production design.

ドロップイン代替品: MC3303DR2 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: MC3303DR2 (同一形状・フットプリント) — 相違点: Architecture, Input Type, Package, Product Type.

Texas Instruments
Architecture: Voltage-feedback
Package: 14-pin SOIC-14
比較対象 MC3303DR2 →
Texas Instruments
Input Type: True differential inputs
Product Type: Quad operational amplifier
比較対象 MC3303DR2 →

MC3302DR2G

✅ ドロップイン
📦 SOIC-14
Same-family 14-pin SOIC candidate; key electrical ratings may differ by up to 20%, so offset, bandwidth, slew rate, and common-mode limits require confirmation.

📋 参考代替品(カタログ未掲載)

MC3403DR

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 SOIC-14
Quad operational amplifier · 4 circuits · ±2.5 V to ±15 V · 30 V · 1 MHz · 0.6 V/µs · −25 °C to 85 °C · True differential inputs

✓ 在庫あり

$0.4102 / 個

データシートを見る →

MC3303D

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 SOIC-14
Standard general-purpose operational amplifier · 4 channels · 4 circuit single-ended · Voltage-feedback · 30 V · 14 V · 1 MHz · 0.6 V/µs

価格はお問い合わせください

データシートを見る →

MC3301DR2G

✅ ドロップイン ⚠️ 仕様未検証
📦 SOIC-14
Same-brand 14-pin SOIC family candidate; key electrical characteristics may differ by up to 30%, making application-level verification essential.

📋 参考代替品(カタログ未掲載)

MC3402D

✅ ドロップイン ⚠️ 仕様未検証
📦 SOIC-14
Same-brand quad SOIC-14 family candidate; key ratings may differ by up to 30%, including offset, noise, bandwidth, and output-swing behavior.

📋 参考代替品(カタログ未掲載)

MC3303DR2 最大定格&電気的特性

Number of Amplifier Circuits 4 circuits
動作電源電圧 3 V to 36 V
Differential Input Offset Voltage 8 mV
Product Type General-purpose operational amplifier
Architecture Quad operational amplifier
Supply Type Single supply
パッケージ 14-pin SOIC
実装タイプ Surface mount
Noise Characteristics Low noise
Input Type Differential input
ピン数 14 pins

MC3303DR2 ピン構成

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
ピン 1 OUT A — Amplifier A output
ピン 2 IN A- — Amplifier A inverting input
ピン 3 IN A+ — Amplifier A non-inverting input
ピン 4 V- — Negative supply connection
ピン 5 IN B+ — Amplifier B non-inverting input
ピン 6 IN B- — Amplifier B inverting input
ピン 7 OUT B — Amplifier B output
ピン 8 OUT C — Amplifier C output
ピン 9 IN C- — Amplifier C inverting input
ピン 10 IN C+ — Amplifier C non-inverting input
ピン 11 V+ — Positive supply connection
ピン 12 IN D+ — Amplifier D non-inverting input
ピン 13 IN D- — Amplifier D inverting input
ピン 14 OUT D — Amplifier D output

主な用途

MC3303DR2 の用途: 6 件s: Industrial Sensor Signal Conditioning, Low-Level Instrumentation Amplification, Process Control and Monitoring, Active Filtering and Signal Conditioning, Audio and Communication Interfaces, Transducer and Current-Loop Interfaces.

🏭

Industrial Sensor Signal Conditioning

The MC3303DR2 fits four-channel industrial sensor conditioning because it combines four general-purpose amplifiers, 3 V to 36 V single-supply operation, low-noise behavior, and an 8 mV differential input offset specification. Each channel can buffer or amplify a transducer output before conversion by an ADC. The wide supply range supports systems operating from compact 3.3 V rails through higher industrial bus-derived supplies. Verify that sensor outputs remain inside the input common-mode range and that the selected gain keeps the amplifier output within its voltage swing. Use short input paths, local supply bypassing, and separate feedback networks for each channel to minimize offset, noise pickup, and channel-to-channel coupling.

🔧

Low-Level Instrumentation Amplification

The MC3303DR2 is suitable for instrumentation paths where small differential signals must be conditioned before measurement. Its four amplifier channels can implement input buffers, differential stages, active filters, and gain stages while the 8 mV differential input offset specification provides a defined basis for error analysis. The low-noise characterization is valuable when operating near the lower end of the signal range. For precision designs, calculate the offset contribution relative to the smallest expected signal and assess input-bias-current error. Keep input leads short, provide stable reference or feedback resistors, and confirm the complete common-mode and output-swing envelope from the manufacturer datasheet before selecting the operating gain.

🏭

Process Control and Monitoring

The four integrated amplifiers in the MC3303DR2 can support process-control and monitoring functions such as conditioning several sensor outputs, generating control references, buffering actuator inputs, and amplifying status signals. Single-supply operation from 3 V to 36 V allows the device to share power with both low-voltage sensors and higher-voltage industrial control circuitry when its operating limits are respected. Using four channels in one 14-pin SOIC reduces package count compared with four separate amplifiers. Designers should partition noisy actuator paths from precision measurement channels, establish a low-impedance reference point, and check that each amplifier has adequate output-current capability. Thermal review should account for total supply dissipation across all four active channels at the highest expected ambient temperature.

📡

Active Filtering and Signal Conditioning

The MC3303DR2 can implement active filters and general-purpose signal-conditioning networks because it provides four amplifiers in one package. A designer can build precision gain stages, anti-alias filters, smoothing networks, and channel-matching circuits without using four separate ICs. The 3 V to 36 V supply range provides flexibility for mixed-voltage systems, while single-supply operation simplifies common grounding. However, active-filter performance depends on resistor tolerance, amplifier open-loop response, noise, and the exact operating gain. Use matched resistor networks where channel consistency matters, avoid placing high-gain feedback routes beside input traces, and confirm the datasheet bandwidth, slew-rate, and output-capacitance limits before selecting component values.

🎧

Audio and Communication Interfaces

The MC3303DR2 can provide low-level amplification and buffering in audio, communications, and interface circuits where four general-purpose amplifier channels are useful. Its low-noise characterization helps preserve small signals, and the broad 3 V to 36 V supply range allows use in systems operating at different rail levels. The device may be used for microphone preamplifier stages, line-level buffers, gain-control circuits, and interface signal conditioning. Actual audio suitability depends on the complete frequency response, noise-density curve, slew rate, and output-drive requirements at the operating gain. Use a clean analog ground and ground reference, decouple the supply locally, and verify maximum output swing before driving downstream circuitry. Higher-bandwidth or rail-to-rail applications may require a different amplifier family.

📊

Transducer and Current-Loop Interfaces

The MC3303DR2 is appropriate for transducer and current-loop interfaces that require multiple low-level amplifier functions in a compact circuit. The four channels can buffer sensor outputs, amplify small voltage differences, drive an analog-to-digital converter input, and support auxiliary monitoring functions. Single-supply operation simplifies grounding in industrial systems, while the 3 V to 36 V range provides broad input-rail flexibility. The designer must verify that the common-mode voltage of the selected 4-20 mA interface remains within the amplifier's permitted input range and that the output does not exceed the downstream converter's input limits. Feedback-resistor accuracy directly affects transimpedance gain, so use suitable resistor tolerance and keep input-node capacitance low to preserve bandwidth and stability.

What is the MC3303DR2?
The MC3303DR2 is an onsemi single-supply quad operational amplifier containing four general-purpose amplifier circuits in a 14-pin SOIC package. According to the manufacturer datasheet description, it is intended for instrumentation and general-purpose signal-conditioning applications. Its 3 V to 36 V supply range supports low-voltage and higher-voltage industrial systems, while the four-channel integration can simplify PCB layout and reduce the number of separate amplifier packages.
What are the key specifications of MC3303DR2 that engineers should know?
The MC3303DR2 integrates four general-purpose operational amplifiers into one 14-pin SOIC and operates from a single 3 V to 36 V supply. The listed differential input offset voltage is 8 mV, and the device is characterized as low noise. These ratings make it a practical choice for multi-channel instrumentation and general analog signal conditioning, subject to checking the datasheet limits for common-mode voltage, output swing, bandwidth, slew rate, and supply current.
Where can I download the MC3303DR2 datasheet PDF?
The MC3303DR2 datasheet is available through the onsemi datasheet link hosted by AllDataSheet at the datasheet URL listed on this page. The manufacturer document describes the device as a single-supply quad operational amplifier. Use the manufacturer's pin-description table and electrical-characteristics tables during design review, and confirm that any downloaded copy carries the correct MC3303 ordering information and current revision before releasing it into a controlled design package.
Where can I find the MC3303DR2 pinout?
The MC3303DR2 pinout is defined by its 14-pin SOIC package and the manufacturer datasheet. The device uses four conventional dual-input operational-amplifier channels with power-supply pins, allowing multiple channels to share the same package. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks because the exposed package form does not change the 14 electrical pin positions.
Is MC3303DR2 suitable for single-supply instrumentation?
Yes, the MC3303DR2 is specifically identified as a single-supply quad operational amplifier with a 3 V to 36 V operating range. That capability is useful for sensor interfaces and industrial signal-conditioning boards that cannot provide a negative rail. The selected input and output voltages must remain inside the amplifier's common-mode and output-swing limits across the complete operating range, including during startup and maximum load.
What is the input offset voltage of MC3303DR2?
The listed differential input offset voltage for the MC3303DR2 is 8 mV. Offset voltage represents the differential input needed to bring an amplifier's output into its intended operating region. For low-level sensor measurements, engineers should compare this value against the signal amplitude, allowable measurement error, and calibration strategy. The manufacturer datasheet should also be checked for test conditions, including supply voltage and common-mode configuration, because offset specifications depend on operating conditions.
What can replace the MC3303DR2?
The closest same-family candidates are the onsemi MC3302DR2G, MC3303D, MC3403DR, MC3301DR2G, and MC3402D when their individual pinouts and electrical limits match the target design. A replacement should be called a true drop-in only after confirming the 14-pin SOIC pin assignment, supply range, common-mode range, output swing, offset voltage, bandwidth, slew rate, and noise specifications. The manufacturer cross-reference tool should be used for final approval.
Is the MC3303DR2 the same as an MC3403DR?
The MC3303DR2 and MC3403DR are related onsemi quad operational-amplifier families in 14-pin SOIC packages, but they are not automatically electrically identical. The MC3403 family may provide different input or output characteristics, so substitution requires checking offset voltage, common-mode range, slew rate, gain-bandwidth product, supply current, output swing, and stability requirements. Confirm the exact pin mapping before treating the MC3403DR as a drop-in replacement.
MC3303DR2 vs MC3302DR2G - which is better for instrumentation?
Choose the MC3303DR2 when its 8 mV differential input offset rating, low-noise characterization, 3 V to 36 V supply range, and four-channel 14-SOIC implementation satisfy the instrumentation design. Consider the MC3302DR2G only after verifying that its offset, bandwidth, slew rate, common-mode range, and output characteristics meet the signal path. The cross-reference listing identifies these as comparable parts, but final selection still requires a complete electrical comparison against the manufacturer datasheets.
When should I choose MC3303DR2 over another quad op amp?
Choose the MC3303DR2 when you need four general-purpose amplifiers, single-supply operation from 3 V to 36 V, low-noise behavior, and an 8 mV differential input offset specification in a 14-pin SOIC. Select another family member when a specific offset, common-mode, bandwidth, slew-rate, noise, rail-to-rail, or output-swing characteristic is required. Consolidation into one quad package can reduce board area, but it does not remove the need to verify each channel's operating limits.
What is the best onsemi equivalent for MC3303DR2?
The MC3403DR is a practical onsemi-family candidate to evaluate because it is also a 14-pin SOIC quad operational amplifier, while the MC3302DR2G is another same-family option identified in a direct comparison listing. Neither should be installed without confirming pin compatibility and the complete AC and DC specifications. For an exact functional drop-in decision, compare both parts against the MC3303DR2 datasheet and validate the operating points used by the target circuit.
How much thermal dissipation should I allow for MC3303DR2?
Thermal dissipation depends on the actual supply voltage, output swing, load current, ambient temperature, and SOIC thermal resistance, so a fixed dissipation value cannot be assigned without operating data. Use the manufacturer supply-current and electrical-characteristics tables, calculate the power in each amplifier and supply path, and apply the package thermal model with the actual PCB copper area. A copper pour and thermal vias can improve heat spreading compared with a small isolated land pattern.
How should I decouple and lay out an MC3303DR2 circuit?
Place the supply bypass capacitor as close as practical to the device's positive-supply and ground pins, and connect each amplifier channel's feedback components close to their corresponding pins. Route sensitive input and feedback traces away from noisy power paths and keep ground returns short. The manufacturer datasheet should be consulted for recommended bypassing and layout because stability and noise performance can be affected by parasitic capacitance, long feedback loops, and incorrect grounding.
Where to buy MC3303DR2 online?
Use the Request a Quote form on this page to request MC3303DR2 availability, current commercial terms, and suitable packaging options. The request should identify the onsemi part number MC3303DR2 and the required quantity. This page does not publish a static commercial quote because prices and inventory change; a current quotation is required for production planning and procurement decisions.
What is the price of MC3303DR2?
The current MC3303DR2 commercial price should be requested through the Request a Quote form on this page. No static unit price is published because distributor prices, quantity breaks, currency, and inventory can change after verification. Include the required order quantity and shipment destination in the request so the returned quotation reflects the appropriate production quantity rather than a generic single-unit indication.
What is the lead time and stock status for MC3303DR2?
MC3303DR2 stock and lead time should be confirmed through the Request a Quote form on this page. Current listings indicate that the part is commercially offered, but listing presence alone does not establish the quantity immediately available for a specific shipment. State the required quantity, date code preference, and acceptable packaging in the request, and confirm the resulting delivery schedule before committing the component to a production schedule.
Is MC3303DR2 in stock?
MC3303DR2 is commercially listed by multiple authorized product channels, but live stock must be confirmed for the requested quantity through the Request a Quote form on this page. A distributor listing does not guarantee that every package quantity is immediately on hand. The quotation response should confirm available quantity, expected lead time, and whether additional units must be sourced to satisfy the complete order.

エンジニアリング参考データ: MC3303DR2 — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the MC3303DR2 when the design needs four general-purpose amplifier channels in a 14-pin SOIC, single-supply operation, low-noise behavior, and an identified 8 mV differential input offset rating. Its 3 V to 36 V supply range is useful for industrial systems that must accommodate multiple rail levels. Evaluate MC3302DR2G when its exact electrical characteristics offer a better match for offset, bandwidth, or slew rate in the target circuit. Consider MC3403DR when its family characteristics better satisfy common-mode, output-swing, noise, or input-stage requirements, while confirming the SOIC-14 pin assignment. MC3301DR2G and MC3402D are same-brand family candidates but require stricter electrical review because their operating ranges and precision specifications differ. For every proposed substitution, compare operating voltage, input common-mode range, output swing, offset, bandwidth, slew rate, noise, stability, and thermal conditions before updating the schematic and BOM.

代替品との比較

パラメータ この製品 MC3302DR2G MC3403DR MC3303D MC3301DR2G MC3402D
Brand onsemi onsemi onsemi onsemi onsemi onsemi
Package SOIC-14 SOIC-14 - same SOIC-14 - same SOIC-14 - same SOIC-14 - same SOIC-14 - same
Amplifier Circuits 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits
General-Purpose Classification General-purpose amplifier General-purpose family General-purpose family General-purpose family General-purpose family General-purpose family

主な差別化要因

  • Four general-purpose amplifiers in one package (vs MC3403DR)
  • Wide single-supply operating range (vs MC3302DR2G)
  • Consolidation for multi-channel analog designs (vs MC3301DR2G)

設計ノート

Confirm the actual supply voltage and signal levels before assigning the amplifier inputs and outputs. The MC3303DR2 is specified for 3 V to 36 V operation, but the permitted input common-mode range and output swing are narrower than the full supply range. Place the supply bypass capacitor close to the positive-supply and ground pins, keep the high-frequency return path short, and check the total dissipation of all four channels at the maximum expected load and ambient temperature.

Route each amplifier's inverting input, non-inverting input, and feedback components close to the corresponding IC pins. Avoid routing sensitive inputs beside supply traces, relay contacts, or switching-node conductors. High-gain stages require especially short feedback paths because parasitic capacitance inside the feedback loop can affect stability. Use a continuous ground plane where practical, provide a low-impedance return for bypass capacitors, and separate precision channels from high-current output circuitry.

Do not treat the 8 mV offset rating as a complete precision specification and do not assume that every 3-36 V circuit operation keeps the signal inside the usable input range. Check offset test conditions, input-bias current, common-mode limits, output swing, gain-bandwidth product, slew rate, and stability against the actual circuit. For low-level measurements, calculate the offset error as a percentage of the smallest input and include resistor tolerance and output-loading effects.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

A cross-reference comparison listing references RoHS and REACH fields, but the exact MC3303DR2 compliance values were not stated clearly enough to classify them. No AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was confirmed.

関連検索

MC3303DR2 datasheet MC3303DR2 pinout MC3303DR2 datasheet pdf MC3303DR2 specifications MC3303DR2 equivalent MC3303DR2 replacement MC3303DR2 cross reference MC3303DR2 SOIC-14 pinout MC3303DR2 vs MC3403DR MC3303DR2 op amp application circuit onsemi MC3303DR2 MC3303DR2 price MC3303DR2 stock

関連部品&用語

onsemi MC3303DR2 MC3302DR2G MC3403DR MC3303D MC3301DR2G MC3402D quad operational amplifier operational amplifier instrumentation amplifier general-purpose amplifier analog signal-conditioning IC single-supply amplifier semiconductor SOIC-14 surface-mount package differential input input offset voltage input common-mode range output voltage swing gain-bandwidth product slew rate low-noise amplification industrial instrumentation
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示