MC33901SEF - Single High-Speed CAN Transceiver | NXP
部品番号: MC33901SEF ✓ 生産中MC33901SEF 概要
A CAN transceiver is the physical-layer interface between a digital controller and a differential CAN network. It converts controller-side logic signals into the dominant and recessive levels used on the bus, while converting received bus states into logic signals for the controller. Within the hierarchy of electronic components, the MC33901SEF is a bus interface IC, a CAN physical-layer transceiver, a communication interface device, and ultimately a semiconductor.
The MC33901SEF is identified as a 1/1 transceiver, meaning that it provides one CAN channel rather than the two or four channels found in some multi-channel transceivers. Its 8-SOIC package supports compact surface-mount layouts in automotive and industrial control equipment. The automotive temperature-grade marking identifies it for vehicle communication applications where environmental robustness and long service life are important design considerations.
The part's principal engineering benefit is straightforward CAN physical connectivity without wakeup or timeout circuitry. This simplifies system partitioning when the host CAN controller already manages low-power behavior, bus monitoring, and diagnostics. Its single-channel architecture also reduces board area and component count compared with a multi-channel transceiver when only one CAN network is required. Designers should verify signaling, supply, protection, and timing requirements against the manufacturer datasheet for the exact operating environment.
Typical uses include vehicle body controllers, engine and transmission electronics, industrial automation equipment, sensor gateways, and embedded control modules. A CAN network is especially useful where multiple nodes need robust, deterministic communication over a multi-conductor differential bus. The MC33901SEF can sit between a microcontroller or dedicated CAN controller and the physical CANH and CANL conductors, with the bus network providing the shared communication medium.
For layout, place the transceiver close to the CAN connector or bus-header pins and keep the CANH and CANL routing short, symmetric, and continuous over a common ground reference. Follow the manufacturer's recommended input and output capacitor placement, provide the specified supply bypass capacitance, and keep switching or high-current return paths away from the bus traces. The 8-SOIC footprint also makes thermal performance dependent on copper area and the surrounding board construction.
This page combines the NXP product identity with practical CAN interface guidance, package details, verified sourcing links, and a conservative review of replacement options. It emphasizes confirmed 8-SOIC compatibility rather than treating every functionally similar CAN receiver as a true drop-in replacement.
ドロップイン代替品: MC33901SEF — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
MC33901SED
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MCP2562FD-E/SN
✅ ドロップイン価格はお問い合わせください
データシートを見る →MC33901SEF 仕様
| Device Type | Single CAN high-speed physical-layer transceiver |
| CAN Channel Count | 1 channel |
| Transmit/Receive Configuration | 1/1 transceiver |
| CAN Network Type | High-speed CAN |
| Wakeup Function | Not included |
| Timeout Function | Not included |
| Package Type | 8-pin SOIC |
| Terminal Count | 8 terminals |
| Package Shape | Rectangular |
| Terminal Form | Gull wing |
| Temperature Grade | Automotive |
| 実装タイプ | Surface mount |
MC33901SEF rectangular ピン配置ガイド
MC33901SEF (rectangular パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: MC33901SEF.
詳細は データシート をご参照ください。
主な用途
MC33901SEF の用途: 6 件s: Automotive Body Control Module, Industrial Automation Controller, Engine and Transmission Electronics, Sensor Network Gateway, Embedded Equipment Communication, Diagnostic and Test System.
Automotive Body Control Module
The MC33901SEF fits an automotive body-control module that connects a microcontroller or CAN controller to a high-speed CAN network. Its confirmed 1/1 transceiver configuration supplies one CAN physical channel, while the 8-pin SOIC package minimizes board space compared with many discrete bus-interface implementations. The automotive temperature-grade identification supports use in vehicle electronics, but the exact ordering code must satisfy the module's environmental requirements. Since wakeup and timeout are absent, low-power and bus-monitoring behavior should be implemented by the host controller or another suitable subsystem.
おすすめ
Industrial Automation Controller
The MC33901SEF can serve as the physical interface between an industrial controller and a high-speed CAN fieldbus. Its single 1/1 CAN channel is appropriate for machines or sensor nodes requiring one network segment, and the 8-pin SOIC package supports conventional surface-mount assembly. The absence of wakeup and timeout functions keeps the physical-layer role focused on communication. Engineers should use the manufacturer layout guidance for bus routing, termination, supply bypassing, and protection because those implementation details determine EMC and fault-tolerance performance more than the package count alone.
おすすめ
Engine and Transmission Electronics
The MC33901SEF is suitable for an engine or transmission electronic control unit that exchanges diagnostic and control data over a high-speed CAN network. One dedicated physical-layer channel is sufficient when the ECU has a single CAN network, and the automotive-grade identity aligns with vehicle electronics requirements. The compact 8-pin SOIC package leaves more board area for sensing, computation, and output drivers. Because the device does not provide wakeup or timeout, the ECU must handle sleep transitions and bus inactivity monitoring at the system or controller level.
おすすめ
Sensor Network Gateway
The MC33901SEF can provide the single CAN physical-layer link used by a gateway that aggregates data from remote sensors. The 1/1 architecture is appropriate when one upstream CAN segment connects the gateway to a higher-level controller, while the SOIC-8 footprint supports compact gateway hardware. Bus routing should preserve the characteristic CANH and CANL pair geometry and minimize exposure to unrelated switching currents. For installations requiring automatic low-power wakeup or inactivity timeout, select a transceiver with those functions rather than adding software assumptions that MC33901SEF does not implement.
おすすめ
Embedded Equipment Communication
The MC33901SEF is appropriate for embedded industrial equipment that exposes a high-speed CAN interface to an operator panel, robot controller, or service computer. A single transceiver channel keeps the bus interface economical and compact in an 8-pin SOIC footprint. The controller-side logic interface and physical CANH/CANL functions are isolated from the bus by the transceiver, reducing the need for discrete bus-driver circuitry. Designers should still include the required bus termination, common-mode protection, and supply decoupling according to the manufacturer's application guidance.
おすすめ
Diagnostic and Test System
The MC33901SEF can serve as the CAN interface in a portable diagnostic tool, hardware-in-the-loop tester, or service equipment connected to a high-speed CAN network. Its 1/1 transceiver configuration provides the required physical layer for one CAN segment, and the SOIC-8 package is easy to assemble using standard surface-mount methods. The absence of wakeup and timeout should be considered when designing a tester that must detect an inactive bus. Cable protection, ground continuity, and termination must be handled at the connector and interface-protection circuit.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC33901SEF — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC33901SED | MCP2562FD-E/SN |
|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | NXP Semiconductors | NXP Semiconductors | Microchip Technology |
| Device Type | Single high-speed CAN transceiver | Single high-speed CAN transceiver | CAN FD fault-tolerant high-speed transceiver |
| CAN Channel Count | 1 channel | 1 channel | 1 channel |
| Terminal Count | 8 terminals | 8 terminals | 8 terminals |
主な差別化要因
- Focused single-channel CAN physical interface (vs MCP2562FD-E/SN)
- No wakeup or timeout circuitry in the identified device (vs MC33901SED)
- Automotive-grade identity in a compact 8-pin package (vs MCP2562FD-E/SN)
設計ノート
Route CANH and CANL as a short, symmetric differential pair over a continuous reference plane. Keep the pair away from switching nodes, high-current return paths, crystal-clock circuitry, and unrelated communication buses. Minimize stubs and avoid unnecessary layer changes; when vias are unavoidable, use a matching transition geometry on both conductors. Place the transceiver close to the bus connector or header to reduce the unterminated portion of the network and improve immunity to external electromagnetic interference.
Decouple the transceiver supply with the capacitance and placement specified by the manufacturer, placing the high-frequency bypass component close to the relevant device pins. Keep the supply return path continuous beneath and around the SOIC-8 footprint, and separate noisy converter currents from the CAN transceiver and controller supply paths. Verify that the selected power source, local regulation, and startup sequence meet the device's electrical limits before releasing the system to the bus.
Do not treat the 8-SOIC footprint alone as proof that a different CAN transceiver is interchangeable. Check pin names, supply voltage, controller-side logic levels, dominant-state behavior, bus fault handling, standby or sleep modes, and termination requirements. MCP2562FD-E/SN adds CAN FD and fault-tolerant functionality, while MC33901SEF is identified without wakeup or timeout; those differences can affect firmware and network behavior even when the footprints align.
Termination belongs at the physical ends of the CAN bus, not at every node. Confirm the complete network topology and termination strategy before energizing the bus, and avoid leaving a disconnected transceiver with an incorrectly configured or floating controller interface. For production hardware, include the required common-mode protection, connector grounding, and bus-fault test coverage so that transient energy and ground offsets do not compromise the communication link.
コンプライアンス情報
The device is identified as automotive temperature grade, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements require confirmation from the manufacturer or an authoritative product declaration.