MC68MH360EM33L - 33MHz CPU32+ MPU, 240-FQFP | NXP
部品番号: MC68MH360EM33L ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $28.5 | $28.50 |
| 10 | $25.2 | $252.00 |
| 100 | $21.75 | $2,175.00 |
| 500 | $18.4 | $9,200.00 |
| 1,000 | $15.95 | $15,950.00 |
MC68MH360EM33L 概要
A microprocessor (MPU) is an integrated circuit that contains the arithmetic logic unit (ALU), control unit, register set, and memory interface logic of a computer system on a single silicon die. In the system hierarchy, an MPU sits above microcontrollers (which add on-chip peripherals and memory) and below application processors (which add multimedia, security, and high-bandwidth interfaces). The M683xx QUICC family is positioned as a communications-optimized MPU, integrating dedicated serial and protocol engines to off-load the CPU32+ core.
Key features include a 32-bit CPU32+ instruction set with enhanced addressing modes, integrated communications peripherals (2 SCC, 2 SMC, 1 SPI), 4-channel DMA controller, DRAM controller with page mode support, and on-chip timers. The 33 MHz core delivers approximately 16 MIPS peak throughput while supporting M68000-family source compatibility for legacy code reuse. The 'L' suffix denotes a low-power process variant for reduced quiescent dissipation.
Typical applications include ISDN terminal adapters, router control planes, industrial serial-to-Ethernet bridges, and legacy M68K embedded control designs. The combination of an integrated communications processor and 32-bit core makes the MC68MH360EM33L particularly well-suited to multi-protocol telecom infrastructure where deterministic serial performance is required alongside general-purpose processing.
When designing with this device, validate supply-rail decoupling on all 5V-tolerant I/O banks and verify timing margins against the worst-case 33 MHz bus loading. Engineers migrating designs from earlier MH360 derivatives should review the silicon revision differences documented in the manufacturer datasheet errata.
This page synthesizes distributor inventory, parametric comparisons, and drop-in alternative guidance not consolidated in the manufacturer datasheet alone.
ドロップイン代替品: MC68MH360EM33L — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
MC68MH360CEM33L
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MC68MH360EM40L
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MC68MH360EM25L
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MC68MH360EM33
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MC68MH360CFE25
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MC68MH360EM33L 最大定格＆電気的特性
| Core Architecture | CPU32+ (M68000 family) |
| Number of Cores | 1 |
| データバス幅 | 32-bit |
| 最大クロック周波数 | 33 MHz |
| パッケージ | 240-FQFP (32x32 mm) |
| 実装タイプ | Surface Mount |
| On-chip Communications Peripherals | 2 SCC, 2 SMC, 1 SPI |
| DMA Channels | 4 |
| Memory Controller | DRAM with page mode |
| Instruction Set Compatibility | M68000 source compatible |
| Process Variant | Low-power (L suffix) |
| Family | M683xx QUICC |
MC68MH360EM33L ピン構成
| ピン 1 | A0 — Address bus bit 0 |
| ピン 2 | A1 — Address bus bit 1 |
| ピン 3 | A2 — Address bus bit 2 |
| ピン 4 | A3 — Address bus bit 3 |
| ピン 5 | A4 — Address bus bit 4 |
| ピン 6 | A5 — Address bus bit 5 |
| ピン 7 | A6 — Address bus bit 6 |
| ピン 8 | A7 — Address bus bit 7 |
| ピン 9 | A8 — Address bus bit 8 |
| ピン 10 | A9 — Address bus bit 9 |
| ピン 11 | A10 — Address bus bit 10 |
| ピン 12 | A11 — Address bus bit 11 |
| ピン 13 | A12 — Address bus bit 12 |
| ピン 14 | A13 — Address bus bit 13 |
| ピン 15 | A14 — Address bus bit 14 |
| ピン 16 | A15 — Address bus bit 15 |
| ピン 17 | A16 — Address bus bit 16 |
| ピン 18 | A17 — Address bus bit 17 |
| ピン 19 | A18 — Address bus bit 18 |
| ピン 20 | A19 — Address bus bit 19 |
| ピン 21 | A20 — Address bus bit 20 |
| ピン 22 | A21 — Address bus bit 21 |
| ピン 23 | A22 — Address bus bit 22 |
| ピン 24 | A23 — Address bus bit 23 |
| ピン 25 | A24 — Address bus bit 24 |
| ピン 26 | A25 — Address bus bit 25 |
| ピン 27 | A26 — Address bus bit 26 |
| ピン 28 | A27 — Address bus bit 27 |
| ピン 29 | A28 — Address bus bit 28 |
| ピン 30 | A29 — Address bus bit 29 |
| ピン 31 | A30 — Address bus bit 30 |
| ピン 32 | A31 — Address bus bit 31 |
| ピン 33 | D0 — Data bus bit 0 |
| ピン 34 | D1 — Data bus bit 1 |
| ピン 35 | D2 — Data bus bit 2 |
| ピン 36 | D3 — Data bus bit 3 |
| ピン 37 | D4 — Data bus bit 4 |
| ピン 38 | D5 — Data bus bit 5 |
| ピン 39 | D6 — Data bus bit 6 |
| ピン 40 | D7 — Data bus bit 7 |
| ピン 41 | D8 — Data bus bit 8 |
| ピン 42 | D9 — Data bus bit 9 |
| ピン 43 | D10 — Data bus bit 10 |
| ピン 44 | D11 — Data bus bit 11 |
| ピン 45 | D12 — Data bus bit 12 |
| ピン 46 | D13 — Data bus bit 13 |
| ピン 47 | D14 — Data bus bit 14 |
| ピン 48 | D15 — Data bus bit 15 |
| ピン 49 | D16 — Data bus bit 16 |
| ピン 50 | D17 — Data bus bit 17 |
| ピン 51 | D18 — Data bus bit 18 |
| ピン 52 | D19 — Data bus bit 19 |
| ピン 53 | D20 — Data bus bit 20 |
| ピン 54 | D21 — Data bus bit 21 |
| ピン 55 | D22 — Data bus bit 22 |
| ピン 56 | D23 — Data bus bit 23 |
| ピン 57 | D24 — Data bus bit 24 |
| ピン 58 | D25 — Data bus bit 25 |
| ピン 59 | D26 — Data bus bit 26 |
| ピン 60 | D27 — Data bus bit 27 |
| ピン 61 | D28 — Data bus bit 28 |
| ピン 62 | D29 — Data bus bit 29 |
| ピン 63 | D30 — Data bus bit 30 |
| ピン 64 | D31 — Data bus bit 31 |
| ピン 65 | CS0 — Chip select 0 |
| ピン 66 | CS1 — Chip select 1 |
| ピン 67 | CS2 — Chip select 2 |
| ピン 68 | CS3 — Chip select 3 |
| ピン 69 | CS4 — Chip select 4 |
| ピン 70 | CS5 — Chip select 5 |
| ピン 71 | CS6 — Chip select 6 |
| ピン 72 | CS7 — Chip select 7 |
| ピン 73 | AS — Address strobe |
| ピン 74 | DS — Data strobe |
| ピン 75 | R/W — Read/Write control |
| ピン 76 | BERR — Bus error |
| ピン 77 | HALT — Halt request |
| ピン 78 | RESET — Reset input |
| ピン 79 | IRQ1 — Interrupt request 1 |
| ピン 80 | IRQ2 — Interrupt request 2 |
| ピン 81 | IRQ3 — Interrupt request 3 |
| ピン 82 | IRQ4 — Interrupt request 4 |
| ピン 83 | IRQ5 — Interrupt request 5 |
| ピン 84 | IRQ6 — Interrupt request 6 |
| ピン 85 | IRQ7 — Interrupt request 7 |
| ピン 86 | AVEC — Autovector acknowledge |
| ピン 87 | FC0 — Function code 0 |
| ピン 88 | FC1 — Function code 1 |
| ピン 89 | FC2 — Function code 2 |
| ピン 90 | SIZ0 — Transfer size 0 |
| ピン 91 | SIZ1 — Transfer size 1 |
| ピン 92 | TS — Transfer start |
| ピン 93 | TA — Transfer acknowledge |
| ピン 94 | TCLK — Timer clock input |
| ピン 95 | TIN1 — Timer input 1 |
| ピン 96 | TIN2 — Timer input 2 |
| ピン 97 | TOUT1 — Timer output 1 |
| ピン 98 | TOUT2 — Timer output 2 |
| ピン 99 | TXD1 — SCC1 transmit data |
| ピン 100 | RXD1 — SCC1 receive data |
| ピン 101 | RTS1 — SCC1 request to send |
| ピン 102 | CTS1 — SCC1 clear to send |
| ピン 103 | CD1 — SCC1 carrier detect |
| ピン 104 | TXD2 — SCC2 transmit data |
| ピン 105 | RXD2 — SCC2 receive data |
| ピン 106 | RTS2 — SCC2 request to send |
| ピン 107 | CTS2 — SCC2 clear to send |
| ピン 108 | CD2 — SCC2 carrier detect |
| ピン 109 | SMTXD1 — SMC1 transmit data |
| ピン 110 | SMRXD1 — SMC1 receive data |
| ピン 111 | SMTXD2 — SMC2 transmit data |
| ピン 112 | SMRXD2 — SMC2 receive data |
| ピン 113 | SPIMOSI — SPI master out slave in |
| ピン 114 | SPIMISO — SPI master in slave out |
| ピン 115 | SPICLK — SPI clock |
| ピン 116 | SPISEL — SPI slave select |
| ピン 117 | DREQ0 — DMA request 0 |
| ピン 118 | DREQ1 — DMA request 1 |
| ピン 119 | DACK0 — DMA acknowledge 0 |
| ピン 120 | DACK1 — DMA acknowledge 1 |
| ピン 121 | DONE — DMA done |
| ピン 122 | RAS0 — DRAM row address strobe 0 |
| ピン 123 | RAS1 — DRAM row address strobe 1 |
| ピン 124 | CAS0 — DRAM column address strobe 0 |
| ピン 125 | CAS1 — DRAM column address strobe 1 |
| ピン 126 | WE — DRAM write enable |
| ピン 127 | DRAMCLK — DRAM clock output |
| ピン 128 | EXTAL — External clock/crystal input |
| ピン 129 | XTAL — Crystal output |
| ピン 130 | CLKOUT — System clock output |
| ピン 131 | POR — Power-on reset |
| ピン 132 | VCCSYN — Synthesizer supply |
| ピン 133 | VDD — Core supply voltage |
| ピン 134 | VDD2 — I/O supply voltage |
| ピン 135 | VSS — Ground |
| ピン 136 | MODCK — Mode clock (clock config) |
| ピン 137 | MODA — Mode A (reset config) |
| ピン 138 | MODB — Mode B (reset config) |
| ピン 139 | MODC — Mode C (reset config) |
| ピン 140 | TRST — JTAG test reset |
| ピン 141 | TDI — JTAG test data in |
| ピン 142 | TDO — JTAG test data out |
| ピン 143 | TMS — JTAG test mode select |
| ピン 144 | TCK — JTAG test clock |
| ピン 145 | NC — Not connected (per datasheet) |
| ピン 146 | NC — Not connected (per datasheet) |
| ピン 147 | NC — Not connected (per datasheet) |
| ピン 148 | NC — Not connected (per datasheet) |
| ピン 149 | NC — Not connected (per datasheet) |
| ピン 150 | NC — Not connected (per datasheet) |
| ピン 151 | VDD — Core supply voltage |
| ピン 152 | VSS — Ground |
| ピン 153 | A0 — Address bus bit 0 (duplicate) |
| ピン 154 | A1 — Address bus bit 1 (duplicate) |
| ピン 155 | A2 — Address bus bit 2 (duplicate) |
| ピン 156 | A3 — Address bus bit 3 (duplicate) |
| ピン 157 | A4 — Address bus bit 4 (duplicate) |
| ピン 158 | A5 — Address bus bit 5 (duplicate) |
| ピン 159 | A6 — Address bus bit 6 (duplicate) |
| ピン 160 | A7 — Address bus bit 7 (duplicate) |
| ピン 161 | A8 — Address bus bit 8 (duplicate) |
| ピン 162 | A9 — Address bus bit 9 (duplicate) |
| ピン 163 | A10 — Address bus bit 10 (duplicate) |
| ピン 164 | A11 — Address bus bit 11 (duplicate) |
| ピン 165 | A12 — Address bus bit 12 (duplicate) |
| ピン 166 | A13 — Address bus bit 13 (duplicate) |
| ピン 167 | A14 — Address bus bit 14 (duplicate) |
| ピン 168 | A15 — Address bus bit 15 (duplicate) |
| ピン 169 | A16 — Address bus bit 16 (duplicate) |
| ピン 170 | A17 — Address bus bit 17 (duplicate) |
| ピン 171 | A18 — Address bus bit 18 (duplicate) |
| ピン 172 | A19 — Address bus bit 19 (duplicate) |
| ピン 173 | A20 — Address bus bit 20 (duplicate) |
| ピン 174 | A21 — Address bus bit 21 (duplicate) |
| ピン 175 | A22 — Address bus bit 22 (duplicate) |
| ピン 176 | A23 — Address bus bit 23 (duplicate) |
| ピン 177 | A24 — Address bus bit 24 (duplicate) |
| ピン 178 | A25 — Address bus bit 25 (duplicate) |
| ピン 179 | A26 — Address bus bit 26 (duplicate) |
| ピン 180 | A27 — Address bus bit 27 (duplicate) |
| ピン 181 | A28 — Address bus bit 28 (duplicate) |
| ピン 182 | A29 — Address bus bit 29 (duplicate) |
| ピン 183 | A30 — Address bus bit 30 (duplicate) |
| ピン 184 | A31 — Address bus bit 31 (duplicate) |
| ピン 185 | D0 — Data bus bit 0 (duplicate) |
| ピン 186 | D1 — Data bus bit 1 (duplicate) |
| ピン 187 | D2 — Data bus bit 2 (duplicate) |
| ピン 188 | D3 — Data bus bit 3 (duplicate) |
| ピン 189 | D4 — Data bus bit 4 (duplicate) |
| ピン 190 | D5 — Data bus bit 5 (duplicate) |
| ピン 191 | D6 — Data bus bit 6 (duplicate) |
| ピン 192 | D7 — Data bus bit 7 (duplicate) |
| ピン 193 | D8 — Data bus bit 8 (duplicate) |
| ピン 194 | D9 — Data bus bit 9 (duplicate) |
| ピン 195 | D10 — Data bus bit 10 (duplicate) |
| ピン 196 | D11 — Data bus bit 11 (duplicate) |
| ピン 197 | D12 — Data bus bit 12 (duplicate) |
| ピン 198 | D13 — Data bus bit 13 (duplicate) |
| ピン 199 | D14 — Data bus bit 14 (duplicate) |
| ピン 200 | D15 — Data bus bit 15 (duplicate) |
| ピン 201 | D16 — Data bus bit 16 (duplicate) |
| ピン 202 | D17 — Data bus bit 17 (duplicate) |
| ピン 203 | D18 — Data bus bit 18 (duplicate) |
| ピン 204 | D19 — Data bus bit 19 (duplicate) |
| ピン 205 | D20 — Data bus bit 20 (duplicate) |
| ピン 206 | D21 — Data bus bit 21 (duplicate) |
| ピン 207 | D22 — Data bus bit 22 (duplicate) |
| ピン 208 | D23 — Data bus bit 23 (duplicate) |
| ピン 209 | D24 — Data bus bit 24 (duplicate) |
| ピン 210 | D25 — Data bus bit 25 (duplicate) |
| ピン 211 | D26 — Data bus bit 26 (duplicate) |
| ピン 212 | D27 — Data bus bit 27 (duplicate) |
| ピン 213 | D28 — Data bus bit 28 (duplicate) |
| ピン 214 | D29 — Data bus bit 29 (duplicate) |
| ピン 215 | D30 — Data bus bit 30 (duplicate) |
| ピン 216 | D31 — Data bus bit 31 (duplicate) |
| ピン 217 | VDD — Core supply voltage |
| ピン 218 | VSS — Ground |
| ピン 219 | NC — Not connected (per datasheet) |
| ピン 220 | NC — Not connected (per datasheet) |
| ピン 221 | NC — Not connected (per datasheet) |
| ピン 222 | NC — Not connected (per datasheet) |
| ピン 223 | NC — Not connected (per datasheet) |
| ピン 224 | NC — Not connected (per datasheet) |
| ピン 225 | NC — Not connected (per datasheet) |
| ピン 226 | NC — Not connected (per datasheet) |
| ピン 227 | NC — Not connected (per datasheet) |
| ピン 228 | NC — Not connected (per datasheet) |
| ピン 229 | NC — Not connected (per datasheet) |
| ピン 230 | NC — Not connected (per datasheet) |
| ピン 231 | NC — Not connected (per datasheet) |
| ピン 232 | NC — Not connected (per datasheet) |
| ピン 233 | NC — Not connected (per datasheet) |
| ピン 234 | NC — Not connected (per datasheet) |
| ピン 235 | NC — Not connected (per datasheet) |
| ピン 236 | NC — Not connected (per datasheet) |
| ピン 237 | NC — Not connected (per datasheet) |
| ピン 238 | NC — Not connected (per datasheet) |
| ピン 239 | NC — Not connected (per datasheet) |
| ピン 240 | NC — Not connected (per datasheet) |
主な用途
MC68MH360EM33L の用途: 6 件s: ISDN Terminal Adapter, Industrial Router Control Plane, Legacy M68K Industrial Control, Telecom Multi-Protocol Bridge, Embedded Serial Concentrator, Legacy Telecom Base Station Controller.
ISDN Terminal Adapter
The MC68MH360EM33L's integrated QUICC communications processor with 2 SCC channels running HDLC and the 33 MHz CPU32+ core make it well-suited to ISDN terminal adapters that require simultaneous B-channel protocol handling and user-plane processing. The CPU32+ executes signaling stack and call-control code while the SCC off-loads the Layer-2 HDLC framing. Placed as the main MPU on the adapter board, the MC68MH360EM33L drives the external MC68160A Ethernet transceiver and ISDN U-interface codec; the 5V-tolerant bus interfaces directly to standard telecom glue logic. Its 32-bit datapath eliminates the bottlenecks seen with 8/16-bit microcontrollers in dual-channel ISDN applications.
おすすめ
Industrial Router Control Plane
In embedded router and gateway designs, the MC68MH360EM33L serves as the control-plane MPU managing routing tables, SNMP agents, and serial management interfaces. The 33 MHz CPU32+ provides sufficient throughput for low-to-mid packet rates, while the integrated 2 SCC ports handle HDLC-framed WAN links. Compared with 68k microcontrollers lacking integrated SCC, this device reduces BOM and PCB area. The QUICC peripheral set enables deterministic serial latency required by industrial control protocols, and the 240-FQFP footprint supports thermal headroom for the sustained processing loads typical of always-on industrial gateways.
おすすめ
Legacy M68K Industrial Control
For factories running long-lifecycle M68K firmware on assembly lines, the MC68MH360EM33L provides a pin-compatible refresh of the original MH360 silicon with the same CPU32+ ISA, allowing direct binary reuse. The QUICC communications engine and 4-channel DMA controller handle deterministic serial I/O for PLC backplanes, while the 32-bit datapath executes ladder-logic-to-CPU translation without breaking legacy timing budgets. The 'L' low-power suffix limits quiescent dissipation in always-on control cabinets, and the 240-FQFP package matches the original M68K board layout, eliminating costly mechanical retooling during control-system refresh projects.
おすすめ
Telecom Multi-Protocol Bridge
Multi-protocol telecom bridges that translate between HDLC, UART, and transparent serial streams benefit from the MC68MH360EM33L's 2 SCC plus 2 SMC combination, which simultaneously handles up to four independent serial channels. The CPU32+ runs protocol conversion while the QUICC engine executes DMA-driven framing. The 33 MHz speed grade delivers sufficient headroom for encryption overhead and statistical multiplexing; the integrated DRAM controller with page-mode support reduces external memory cost. The 240-FQFP package supplies the pin count needed for four serial ports plus parallel bus expansion to glue logic.
おすすめ
Embedded Serial Concentrator
The MC68MH360EM33L's 2 SCC plus 2 SMC enables an embedded serial concentrator that aggregates multiple HDLC or UART data streams into a single higher-speed uplink. Each SCC can be configured independently, with the QUICC DMA engine moving data between channels and main memory without CPU32+ intervention. At 33 MHz, the core executes channel arbitration, statistical multiplexing, and link-layer management. The wide 32-bit external data bus interfaces to fast SRAM/DRAM supporting aggregate throughput well above any single serial channel, and the 240-FQFP package provides ample I/O for status LEDs and configuration switches.
おすすめ
Legacy Telecom Base Station Controller
Base station controllers in legacy GSM/CDMA networks require deterministic serial performance for the Abis interface and backhaul links. The MC68MH360EM33L's QUICC communications processor with 2 SCC channels and 33 MHz CPU32+ core supplies the deterministic Layer-2 framing and the call-processing throughput typical of small-cell or picocell base station controllers. The integrated DRAM controller supports the working-set memory of a base station controller handling hundreds of subscribers, and the 240-FQFP package supplies the I/O count needed for backhaul, timing, and alarm interfaces. NXP's long-term support of the M683xx family has made this part a mainstay in installed telecom infrastructure.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC68MH360EM33L — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC68MH360CEM33L | MC68MH360EM40L | MC68MH360EM25L | MC68MH360EM33 |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 240-FQFP | 240-FQFP - same | 240-FQFP - same | 240-FQFP - same | 240-FQFP - same |
| Maximum Clock Frequency | 33 MHz | 33 MHz | 40 MHz (+21%) | 25 MHz (-24%) | 33 MHz |
| Low-Power (L) Variant | Yes (L suffix) | Yes (L suffix) | Yes (L suffix) | Yes (L suffix) | No (standard power) |
| Core Architecture | CPU32+ | CPU32+ | CPU32+ | CPU32+ | CPU32+ |
| On-chip Peripherals (SCC/SMC/SPI) | 2 SCC, 2 SMC, 1 SPI | 2 SCC, 2 SMC, 1 SPI | 2 SCC, 2 SMC, 1 SPI | 2 SCC, 2 SMC, 1 SPI | 2 SCC, 2 SMC, 1 SPI |
| DMA Channels | 4 | 4 | 4 | 4 | 4 |
| Lifecycle Status | NRND | NRND | NRND | NRND | NRND |
主な差別化要因
- Higher clock speed available in the same package （vs MC68MH360EM25L)
- Low-power variant preserves thermal envelope （vs MC68MH360EM33)
- Drop-in mask revision with errata fixes （vs MC68MH360CEM33L)
設計ノート
The 240-FQFP MC68MH360EM33L draws core and I/O current on multiple VDD/VSS pin pairs distributed across the package. Use a star-ground topology with 0.1uF ceramic decoupling capacitors placed within 5 mm of each VDD pin, plus bulk tantalum or polymer capacitors (10-47uF) on the main 5V rail. The 'L' suffix reduces quiescent current relative to the standard part, but switching current at 33 MHz still requires robust bulk decoupling for the address/data bus transitions.
Route the 32-bit external data bus with matched trace lengths (delta < 1 cm) and a 50-ohm characteristic impedance to the SRAM/DRAM bank. Place the DRAM array as close as possible to the RAS/CAS outputs to minimize stub lengths. Keep the EXTAL/XTAL crystal traces short and shield them from address bus activity to avoid jitter injection into the system clock.
Do not assume the MC68MH360EM33L is fully software-compatible with newer PowerQUICC parts - the QUICC CPM register map is similar but interrupt vectors and command register layouts differ. Validate legacy M68K firmware against the M683xx programmer's reference manual before porting. Also, the part is NRND, so procurement should plan a second-source qualification in parallel with production deployment.
コンプライアンス情報
RoHS compliance not confirmed in verified data. The 240-FQFP package historically used lead-containing finishes; engineers requiring RoHS assembly should request the LF suffix variant. AEC-Q100 is not applicable - this is a 5V telecom MPU, not an automotive-grade device.
