MC9S08PB16MTG - 8-Bit 20MHz MCU with 16KB Flash | NXP
部品番号: MC9S08PB16MTG ✓ 生産中MC9S08PB16MTG 概要
A microcontroller is a programmable semiconductor that combines a CPU core, memory, peripherals, and interface circuitry on one integrated circuit. The S08 MCU belongs to the microcontroller hierarchy within embedded processors and semiconductor devices. MC9S08PB16MTG targets cost-sensitive embedded systems that require more than simple logic control but do not need the processing capability or power consumption of a 32-bit MCU.
The principal features include an 8-bit S08 CPU operating up to 20 MHz, 16 KB of flash memory for firmware storage, and 1 KB of data RAM. The analog subsystem provides a 12-bit ADC and comparator, while the integrated amplifier and analog multiplexer reduce the need for external signal-conditioning components. An I2C interface supports connection to sensors, EEPROMs, and other serial peripherals, and flexible timer resources support periodic measurement, motor timing, and control-loop functions.
The S08 architecture combines a compact 8-bit processing core with on-chip flash and RAM, providing deterministic behavior for embedded control. Its 2.7 V to 5.5 V supply range supports both 3.3 V and 5 V systems. The 14 available I/O pins provide flexibility for digital interfaces, while the 12-bit ADC supports analog sensing without requiring a separate converter. An integrated comparator can implement threshold detection or basic analog switching functions.
Typical applications include industrial control panels, small sensor nodes, appliance controllers, LED lighting systems, battery-powered instruments, and compact motor-control boards. The I2C interface is particularly useful in designs combining environmental sensing with a serial EEPROM. The ADC can monitor potentiometers, thermistors, and resistive sensor bridges, while the timers establish reliable sampling or actuator-control intervals without excessive software overhead.
Designers should allocate decoupling capacitors close to the supply pins and route analog inputs away from switching nodes. Firmware must account for the 1 KB RAM limit and should avoid unnecessary dynamic allocation. ADC averaging or calibration can improve measurement consistency, and the selected sensor impedance should be checked against the analog-input sampling requirements in the manufacturer datasheet.
This page combines the device specifications, sourcing guidance, package information, drop-in family alternatives, and practical embedded-design considerations. It also identifies engineering differences among same-footprint S08 options, helping teams choose flash capacity, analog resources, and operating grade without changing the PCB footprint.
ドロップイン代替品: MC9S08PB16MTG — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MC9S08PB16MTG (同一形状・フットプリント) — 相違点: Maximum Operating Temperature, Minimum Operating Temperature, Number of I/O Pins, Package, Serial Interface.
MC9S08PB32MTG
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MC9S08PB12MTG
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MC9S08PB8MTG
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →MC9S08PA16MTG
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MC9S08PA8MTG
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MC9S08PB16MTG 最大定格&電気的特性
| CPU Core | 8-bit S08 |
| 最大クロック周波数 | 20 MHz |
| Flash Program Memory | 16 KB (16K x 8) |
| Data RAM | 1 KB |
| データバス幅 | 8 bit |
| ADC Resolution | 12 bit |
| Number of I/O Pins | 14 |
| 動作電源電圧 | 2.7 V to 5.5 V |
| Minimum Operating Temperature | -40 °C |
| Maximum Operating Temperature | +125 °C |
| パッケージ | 16-TSSOP |
| Package Width | 4.40 mm |
| 実装タイプ | Surface Mount |
| Serial Interface | I2C |
| Analog Features | 12-bit ADC, analog comparator, and amplifier |
| Timer Features | Flexible timers |
| Series | S08 |
| ライフサイクル状態 | Active |
MC9S08PB16MTG ピン構成
| ピン 1 | PTB0 — Port B timer or general-purpose I/O pin |
| ピン 2 | PTB1 — Port B timer or general-purpose I/O pin |
| ピン 3 | PTB2 — Port B timer or general-purpose I/O pin |
| ピン 4 | PTB3 — Port B timer or general-purpose I/O pin |
| ピン 5 | VDD — Power supply input |
| ピン 6 | PTA0 — Port A general-purpose or analog I/O pin |
| ピン 7 | PTA1 — Port A general-purpose or analog I/O pin |
| ピン 8 | PTA2 — Port A general-purpose or analog I/O pin |
| ピン 9 | PTA3 — Port A general-purpose or analog I/O pin |
| ピン 10 | PTA4 — Port A general-purpose or analog I/O pin |
| ピン 11 | PTA5 — Port A general-purpose or analog I/O pin |
| ピン 12 | VSS — Ground reference |
| ピン 13 | PTA6 — Port A general-purpose or analog I/O pin |
| ピン 14 | PTA7 — Port A general-purpose or analog I/O pin |
| ピン 15 | PTB4 — Port B timer or general-purpose I/O pin |
| ピン 16 | PTB5 — Port B timer or general-purpose I/O pin |
主な用途
MC9S08PB16MTG の用途: 6 件s: Industrial Sensor Interface, Appliance Control Panel, Battery-Powered Environmental Monitor, LED Lighting Controller, Compact Motor Controller, Networked Sensor Gateway.
Industrial Sensor Interface
The MC9S08PB16MTG fits industrial sensor interfaces that require local analog measurement without the cost of a higher-performance processor. Its 12-bit ADC can digitize resistive sensors, while the 20 MHz S08 core provides enough timing margin for filtering, calibration, and control logic. The 16 KB flash stores application firmware and parameter tables, and the 1 KB RAM supports bounded sample buffers. With I2C available, the controller can also manage sensors or configuration EEPROMs. A 2.7 V to 5.5 V operating range supports both 3.3 V and 5 V field equipment, provided external signal conditioning matches the ADC input limits.
おすすめ
Appliance Control Panel
The MC9S08PB16MTG is appropriate for appliance control panels that combine touch or potentiometer inputs, indicator outputs, and serial configuration devices. Its 14 I/O pins can support keys, status signals, relays, and display-control lines, while the 12-bit ADC supports analog panel controls without an external converter. The 16 KB flash provides practical room for state machines, calibration, and communication protocols, and the 1 KB RAM is sufficient for bounded display and input buffering. The MCU's I2C interface simplifies connection to an EEPROM or sensor, while its 2.7 V to 5.5 V range accommodates common appliance control boards.
おすすめ
Battery-Powered Environmental Monitor
The MC9S08PB16MTG can serve as the controller in a battery-powered environmental monitor using resistive or ratiometric sensors. Its 12-bit ADC provides useful resolution for temperature, humidity, and light measurements, while the 8-bit CPU performs sampling, averaging, threshold detection, and data formatting. The 16 KB flash accommodates protocol handlers and calibration coefficients, and the 1 KB RAM avoids the need for an external memory device in compact monitoring products. I2C permits connection to serial sensors or a small external EEPROM. The 2.7 V minimum operating voltage also gives designers flexibility when using regulated power derived from a single-cell source.
おすすめ
LED Lighting Controller
The MC9S08PB16MTG is well suited to compact LED lighting controllers that require deterministic timing, simple dimming, and low-cost communication. Flexible timers can generate repeatable PWM or switching intervals, and the available I/O pins can drive channel-enable signals or interface to an LED driver. The 16 KB flash is useful for storing lighting scenes, calibration, and communication logic, while the 1 KB RAM supports multiple channels and state management. The MCU's 2.7 V to 5.5 V operating range supports low-voltage control boards and conventional 5 V logic, provided the LED power stage has its own protection and thermal design.
おすすめ
Compact Motor Controller
The MC9S08PB16MTG can support compact motor-control systems where the MCU performs sequencing, speed-reference interpretation, and fault supervision while an external power stage handles the motor current. Its 20 MHz maximum clock supports responsive timer-based control, and the 14 I/O pins provide encoder inputs, direction controls, enable signals, and status monitoring. The 16 KB flash accommodates motion tables and control firmware, while the 1 KB RAM is adequate for bounded position or speed state. The 12-bit ADC can monitor a current or position signal if its input limits match the sensing circuit, and the 2.7 V to 5.5 V range supports separate logic and power domains.
おすすめ
Networked Sensor Gateway
The MC9S08PB16MTG can act as a protocol-conversion gateway between an I2C sensor and a serial host interface. Its 16 KB flash provides room for protocol frames, device filtering, and configuration commands, while the 1 KB RAM can hold bounded transmit and receive buffers. The 12-bit ADC supports local analog supervision, and the flexible timers handle periodic sampling and communication timing. Its 2.7 V to 5.5 V operating range allows deployment in 3.3 V sensor nodes or 5 V embedded systems. The compact 16-TSSOP package also helps when the gateway must fit alongside a connector, isolated interface, or radio module.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC9S08PB16MTG — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC9S08PB32MTG | MC9S08PB12MTG | MC9S08PB8MTG | MC9S08PA16MTG | MC9S08PA8MTG |
|---|---|---|---|---|---|---|
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| CPU Core | 8-bit S08 | 8-bit S08 | 8-bit S08 | 8-bit S08 | 8-bit S08 | 8-bit S08 |
| Flash Memory | 16 KB | 32 KB | 12 KB | 8 KB | 16 KB | 8 KB |
| Number of I/O Pins | 14 | 14 | 14 | 14 | 14 | 14 |
主な差別化要因
- Provides 16 KB of flash within the compact 16-TSSOP S08PB family (vs MC9S08PB8MTG)
- Maintains the same family footprint while allowing firmware expansion (vs MC9S08PB32MTG)
- Uses a 14-I/O S08PB configuration with integrated analog conversion (vs MC9S08PA16MTG)
設計ノート
Place the MCU supply bypass capacitor adjacent to the VDD and VSS pins and keep the connection to ground short. The 2.7 V to 5.5 V operating range does not remove the need for local decoupling because the 20 MHz S08 core can create fast switching current. Route high-current loads and inductive traces away from the MCU and analog pins. Confirm the exposed pad and thermal-via requirements against the manufacturer package drawing before releasing the PCB footprint.
Treat analog inputs as sensitive nodes even though the MCU includes a 12-bit ADC, comparator, and amplifier. Keep analog traces short, separate them from clock and switching-node routing, and ground the analog return path carefully. Sensor impedance and acquisition time must be checked against the ADC sampling characteristics in the manufacturer datasheet. If the source impedance is high, add a local buffer or capacitor rather than increasing software averaging to compensate for an unsuitable signal source.
Do not assume that a same-package S08 variant is interchangeable without checking memory capacity, pin multiplexing, peripheral differences, and errata. The 1 KB RAM limit can cause failures if firmware uses stack-heavy libraries, large buffering, or dynamic allocation. Favor static allocation and bounded buffers, preserve required reset and clock behavior, and test the production firmware against the exact replacement MPN. A package-compatible footprint alone is not sufficient for a production substitution.
Choose the external supply and decoupling network so the MCU remains within its 2.7 V to 5.5 V operating range under transient load. The 20 MHz clock does not imply that the MCU directly powers the load; use suitable drivers for motors, LEDs, relays, or high-current sensors. Separate sensitive analog rails from digital activity where practical, and account for startup current, peripheral loading, and the voltage drop across any series resistance or regulator in the final power-budget calculation.
コンプライアンス情報
Compliance status must be confirmed for the exact orderable MPN using the current NXP product documentation or supplier declarations. The available product information confirms an active lifecycle state but does not establish the requested compliance classifications.