MC9S08RC16CFG - 8-Bit 8MHz 16KB MCU | NXP | 44-LQFP
部品番号: MC9S08RC16CFG ✗ 生産終了MC9S08RC16CFG 概要
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripheral functions onto one device. The S08 architecture belongs to the embedded processor hierarchy and combines a compact instruction set, dedicated I/O, timers, serial interfaces, and Flash-based firmware storage. The MC9S08RC16CFG is therefore positioned between simple fixed-function controllers and higher-performance microcontrollers used in networking or graphics-intensive equipment.
The device provides 16 KB, or 16K by 8 bits, of Flash program memory and an 8 MHz maximum operating frequency. Its stated operating-voltage range of 1.8 V to 3.6 V supports low-voltage embedded systems. The 44-LQFP package provides 44 external connection points in a compact 10 mm by 10 mm surface-mount body, allowing designers to retain a relatively high pin count without moving to a larger through-hole package.
The S08 architecture emphasizes economical control of embedded peripherals and deterministic firmware execution. Designers can use the available I/O pins for digital interfaces, timing functions, sensor acquisition, and actuator control. Because the processor is 8-bit rather than 32-bit, code density and arithmetic performance may differ from ARM-based microcontrollers, but the simpler architecture can remain effective for control-oriented products with modest data-processing requirements.
Typical applications include building controls, household appliances, battery-operated instruments, compact industrial controllers, sensor interfaces, and small motor-control systems. The 8 MHz clock and 16 KB Flash configuration are well matched to products that coordinate several peripheral functions without requiring an operating system, high-speed communications, or extensive external storage.
The principal design consideration is firmware and peripheral planning before PCB layout. Confirm the exact pin multiplexing, reset requirements, clock configuration, and decoupling recommendations in the manufacturer datasheet. The 1.8 V to 3.6 V operating range also requires a supply regulator and bulk and high-frequency bypass capacitors placed close to the power pins according to the reference circuit.
This page combines the identified electrical characteristics, package information, sourcing guidance, and practical selection criteria for the MC9S08RC16CFG. It also distinguishes documented device facts from parameters that require direct confirmation in the manufacturer datasheet, helping engineers plan sourcing and hardware qualification without confusing related S08 variants.
ドロップイン代替品: MC9S08RC16CFG — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
MC9S08RC16CFGE
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MC9S08RC16CFG 最大定格&電気的特性
| Product Type | 8-bit S08 Flash Microcontroller |
| Maximum CPU Frequency | 8 MHz |
| Flash Memory | 16 KB (16K x 8 bits) |
| Processor Architecture | S08 8-bit architecture |
| Operating Voltage Range | 1.8 V to 3.6 V |
| パッケージ | 44-LQFP (10 mm x 10 mm) |
| 実装タイプ | Surface mount |
| ピン数 | 44 pins |
MC9S08RC16CFG 44-lqfp (10 mm x 10 mm) ピン配置ガイド
MC9S08RC16CFG (44-lqfp (10 mm x 10 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: MC9S08RC16CFG.
詳細は データシート をご参照ください。
主な用途
MC9S08RC16CFG の用途: 6 件s: Building and HVAC Controls, Household Appliance Control, Battery-Powered Sensor Interfaces, Compact Motor and Actuator Control, Test and Measurement Instruments, Embedded Access and Security Control.
Building and HVAC Controls
The MC9S08RC16CFG is suitable for small building-control modules that monitor switches, sensors, and user inputs while driving indicators, relays, or communication interfaces. Its 8 MHz S08 processor and 16 KB of Flash provide sufficient control logic for scheduled operations, debouncing, state management, and fault detection without an operating system. The 44-LQFP package also offers enough external pins for distributed digital I/O in a compact board. Because the controller operates from 1.8 V to 3.6 V, the design must include an appropriate regulated supply and local bypass capacitance. Verify timer, serial-interface, and pin-multiplexing assignments in the manufacturer datasheet before allocating the board’s connector and sensor circuits.
おすすめ
Household Appliance Control
The MC9S08RC16CFG can serve as the central controller in a compact appliance by combining user-interface inputs, temperature or level sensing, motor timing, and discrete output control. Its 16 KB Flash is appropriate for a dedicated firmware state machine, while the 8 MHz operating rate supports responsive polling and timing without high-cost memory resources. The 1.8 V to 3.6 V operating range fits low-voltage product architectures, although motors, heaters, and relays will require suitable driver stages and protection. Designers should partition analog sensing from switching nodes and place input, output, and ground returns carefully. Firmware size, peripheral availability, and the exact suffix-specific temperature rating must be confirmed before freezing the appliance design.
おすすめ
Battery-Powered Sensor Interfaces
The MC9S08RC16CFG is appropriate for compact sensor interfaces that gather periodic measurements, apply calibration, and communicate results over a low-speed serial link. Its 8 MHz S08 core is more than adequate for many acquisition and filtering routines, while 16 KB of Flash can hold application firmware and calibration tables. The 1.8 V minimum operating voltage supports direct integration with appropriately regulated low-energy rails. For battery life, the designer should evaluate sleep currents, wake-up behavior, sensor duty cycle, and regulator efficiency in addition to processor speed. Any high-impedance sensor input needs careful grounding and guarding, while the controller supply should have local high-frequency bypass capacitance close to its power pins.
おすすめ
Compact Motor and Actuator Control
The MC9S08RC16CFG can control low-power actuators, solenoids, small motors, or relay-based outputs when the design uses external transistor and flyback circuitry. The S08 core’s 8 MHz clock supports deterministic sequencing of motion steps, timeout monitoring, and input interlocks, while the 16 KB Flash capacity is practical for a dedicated embedded-control application. Its 44-LQFP package provides a practical mix of I/O and power connections for a compact controller board. The MCU should not drive inductive loads directly; use appropriately rated drivers, snubber networks, and protection against back-EMF. Also separate motor-current paths from sensitive signal returns and confirm the available timer channels in the manufacturer datasheet before assigning precise timing functions.
おすすめ
Test and Measurement Instruments
The MC9S08RC16CFG can serve in compact measurement products that combine sensor conditioning, digital calibration, status reporting, and local user controls. Its 8 MHz S08 processor is suitable for sequential sampling and deterministic threshold logic, and the 16 KB Flash capacity can hold a focused test routine without requiring external program storage. The 44-LQFP package is useful when a measurement product needs both control I/O and access to communication or programming signals. Precision analog performance will depend on external components and layout because the listed MCU characteristics do not define a complete analog front end. Keep sensitive analog paths away from switching nodes, use a clean regulated supply, and verify the available serial and timer resources against the instrumentation protocol.
おすすめ
Embedded Access and Security Control
The MC9S08RC16CFG can support compact access-control, keypad, intercom, or simple security-control modules that manage digital credentials, status LEDs, lock requests, and network or serial handshakes. Its 16 KB Flash is appropriate for a constrained control application, and the 8 MHz S08 architecture provides responsive peripheral polling without a high-complexity processor. The 1.8 V to 3.6 V operating range can simplify integration with low-voltage board-level supplies, although the final power budget depends on the external communication and lock-driver circuits. Security designs should not rely solely on the MCU for cryptographic protection unless suitable validated functions are explicitly provided. Review pin multiplexing, boot and programming behavior, and the final electrical requirements in the manufacturer documentation.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC9S08RC16CFG — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC9S08RC16CFGE |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 44-LQFP (10x10) | 44-LQFP (10x10) |
| Architecture | S08 8-bit | S08 8-bit |
| Maximum CPU Frequency | 8 MHz | 8 MHz |
| Flash Memory | 16 KB | 16 KB |
| Pin Count | 44 pins | 44 pins |
主な差別化要因
- Compact 44-LQFP implementation of the S08 control platform (vs MC9S08RC16CFGE)
- 8 MHz S08 processing with 16 KB Flash (vs MC9S08RC16CFGE)
- Low-voltage operating range for compact embedded systems (vs MC9S08RC16CFGE)
設計ノート
Design the supply rail to remain within the device's stated 1.8 V to 3.6 V operating range across temperature and load. Place the required bulk capacitor and a high-frequency ceramic bypass capacitor close to the supply and ground pins, with the shortest return path possible. Confirm the exact capacitor values, allowable ESR, and regulator recommendations in the manufacturer datasheet rather than copying values from another S08 device.
Assign all 44 LQFP positions from the manufacturer pin-description table before schematic capture. Separate analog and low-level sensor routing from digital switching and relay-driver outputs, and provide a quiet ground reference for sensitive inputs. A compact 10 mm by 10 mm LQFP also needs careful inspection of solder paste volume, pad geometry, and reflow profile to avoid open joints or bridging between fine-pitch leads.
Do not treat a related MC9S08RC16 ordering suffix as interchangeable until its temperature grade, qualification, clock, and electrical limits have been compared with the MC9S08RC16CFG. In particular, verify reset behavior, oscillator options, boot configuration, programming signals, and alternate pin functions. Also confirm that the firmware fits within the 16 KB Flash allocation; a pin-compatible replacement is not useful if its memory map or peripheral set differs.
The identified component characteristics cover the core clock, Flash size, voltage range, and package, but do not establish every RAM, EEPROM, timer, ADC, or serial-interface detail. Validate those resources directly against the MC9S08RC16 datasheet before committing firmware and board routing. This prevents a design from assuming a peripheral or memory feature that is absent, qualified differently, or assigned to a different pin in the selected suffix.
コンプライアンス情報
The identified product information does not provide exact suffix-specific environmental or regulatory declarations. Request current manufacturer documentation before making a compliance claim.