Microchip Technology

MCP604T-E/SL - 2.8MHz Quad CMOS Op Amp | Microchip

部品番号: MCP604T-E/SL ✓ 生産中
2.7 V Vdss 230 µA Id 14-pin SOIC Package
MOQ: 1 |

MCP604T-E/SL 概要

The Microchip Technology MCP604T-E/SL is a low-power quad CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 µA typical operating current, and rail-to-rail output capability. The device operates from a single supply as low as 2.7 V and is packaged in a 14-pin SOIC. Each channel combines low bias current, high open-loop gain, and rail-to-rail output swing for portable and low-voltage signal-processing systems.

An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The quad configuration provides four amplifiers in one package, reducing board area compared with four individual devices. Within the broader hierarchy of semiconductor components, the MCP604 belongs to the operational-amplifier class, analog ICs, and signal-conditioning electronics. Its low operating current makes it suitable for battery-powered equipment, instrumentation, sensor interfaces, and general-purpose analog signal paths.

The MCP604’s principal characteristics include a 2.8 MHz gain-bandwidth product, 2.3 V/µs slew rate, approximately 1 pA input bias current, and a 2 mV input-offset voltage as listed for this ordering code. Rail-to-rail output operation allows the output to approach the supply rails, improving output swing in low-voltage systems. A minimum supply of 2.7 V supports compatibility with 3.3 V system rails while retaining a typical operating current of 230 µA.

Microchip’s advanced CMOS process gives the MCP604 low bias current, high open-loop gain, and low static power requirements. The combination of a 2.8 MHz gain-bandwidth product and 2.3 V/µs slew rate supports moderate-bandwidth closed-loop amplifier configurations. Because the amplifiers are intended for low-voltage operation, input common-mode range, output swing, noise, offset, and stability should be checked against the specific gain and load conditions used in the final circuit.

Typical uses include portable sensor conditioning, low-voltage data acquisition, current-to-voltage conversion, active filtering, and general buffer or gain stages. The quad organization is particularly useful when a design needs several matched-function channels, such as two differential amplifier stages or four independent low-frequency signal conditioners. The 14-pin SOIC also supports conventional leaded-package assembly and prototype-board layouts.

When designing around the MCP604T-E/SL, place the input and output paths away from switching-node and high-current return paths to reduce coupling into the low-bias-current amplifier. Confirm the usable input and output ranges at the selected supply voltage, and verify stability with the intended source impedance, load, feedback network, and gain. Proper bypassing and a quiet ground-reference arrangement are especially important in battery-powered precision measurement systems.

ドロップイン代替品: MCP604T-E/SL — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: MCP604T-E/SL (同一形状・フットプリント) — 相違点: Package, Gain-Bandwidth Product, Amplifier Type, Maximum Input Offset Voltage, Slew Rate.

Microchip Technology
Package: 14-SOIC, 3.90 mm body width
Gain-Bandwidth Product: 2.8 MHz typical
Amplifier Type: General-purpose CMOS operational amplifier
Microchip Technology
Maximum Input Offset Voltage: 2,000 uV
Microchip Technology
Package: 14-pin SOIC, 3.90 mm width

MCP604T-I/SL

✅ ドロップイン
Microchip Technology
📦 14-pin SOIC
4 channels · CMOS operational amplifier · 2.8 MHz · 2.7 V · 6.0 V · 230 µA per amplifier · 1 pA · 2.3 V/µs

価格はお問い合わせください

データシートを見る →

MCP604-I/SL

✅ ドロップイン
Microchip Technology
📦 14-pin SOIC
Quad CMOS operational amplifier · 4 circuits · 2.8 MHz · 230 uA · 2.7 V to 6.0 V · 2.7 V · 2,000 uV · Rail-to-rail

価格はお問い合わせください

データシートを見る →

MCP604-E/SL

✅ ドロップイン
Microchip Technology
📦 14-pin SOIC
4 circuits · General-purpose CMOS operational amplifier · 2.8 MHz typical · 2.3 V/us typical · 230 uA · 2.7 V to 5.5 V · Yes · Yes

価格はお問い合わせください

データシートを見る →

MCP6L04T-E/SL

✅ ドロップイン
📦 14-pin SOIC
Related low-power quad rail-to-rail amplifier family; exact bias-current, offset, slew-rate, and temperature-limit differences require confirmation.

📋 参考代替品(カタログ未掲載)

MCP604T-E/SL 最大定格&電気的特性

Amplifier Type Quad CMOS operational amplifier
Number of Channels 4 channels
Gain-Bandwidth Product 2.8 MHz
Slew Rate 2.3 V/µs
Typical Operating Current 230 µA
Minimum Single-Supply Voltage 2.7 V
Maximum Supply Voltage 6 V
Input Bias Current 1 pA
Maximum Input Offset Voltage 2 mV
Output Swing Rail-to-rail
Process Technology Advanced CMOS
Open-Loop Gain High open-loop gain
パッケージ 14-pin SOIC
実装タイプ Surface mount
Automotive Qualification AEC-Q100
RoHS ステータス Compliant
ライフサイクル状態 Active

MCP604T-E/SL 14-pin soic ピン配置ガイド

MCP604T-E/SL (14-pin soic パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

MCP604T-E/SL の 14-pin soic パッケージピン配置図

詳細なピン配置データはありません: MCP604T-E/SL.

詳細は データシート をご参照ください。

主な用途

MCP604T-E/SL の用途: 6 件s: Portable Sensor Signal Conditioning, Battery-Powered Data Acquisition, Active Filtering and Gain Stages, Industrial Current Monitoring, Low-Voltage Interface Buffering, Automotive Low-Power Conditioning.

📱

Portable Sensor Signal Conditioning

The MCP604T-E/SL fits portable sensor front ends that require low bias current and a small analog signal-conditioning footprint. Its approximately 1 pA input bias current minimizes loading on high-impedance sources, while the 230 µA typical operating current helps preserve battery life. The 2.8 MHz gain-bandwidth product supports low- and moderate-bandwidth gain stages. Four amplifiers can provide sensor buffering, gain, filtering, and output conditioning without requiring separate packages. Because rail-to-rail output increases available signal swing, the circuit remains useful with low-voltage sensors, although the input common-mode range must be checked at the selected supply voltage.

⚡

Battery-Powered Data Acquisition

The MCP604T-E/SL is useful in battery-powered data-acquisition systems where four conditioned channels are needed at low power. The 2.7 V minimum single-supply operation supports 3.3 V systems, and the 230 µA typical operating current reduces the amplifier’s contribution to standby consumption. Its 1 pA bias current helps when the inputs come from high-impedance sensors or leakage-sensitive dividers. The 2.8 MHz bandwidth and 2.3 V/µs slew rate accommodate modest-frequency instrumentation. Designers should still account for sensor excitation, reference accuracy, ADC input range, and the amplifier’s settling behavior in the complete acquisition chain.

🔧

Active Filtering and Gain Stages

The MCP604T-E/SL can implement the gain and active-filter stages required in low-frequency measurement chains. Its 2.8 MHz gain-bandwidth product provides useful bandwidth for precision amplifier networks, while the four channels allow a practical multi-stage filter without four separate packages. The approximately 2 mV listed input-offset voltage must be included in the error budget for low-level signals, and the 1 pA bias current is advantageous for high-impedance networks. Stable operation requires checking the feedback topology, source impedance, load capacitance, and component tolerances against the device’s stability characteristics.

🏭

Industrial Current Monitoring

The MCP604T-E/SL can amplify the small voltage produced by a current-sense element in an industrial monitoring circuit. Low input bias current helps avoid disturbing the sense path, while the 2.8 MHz gain-bandwidth product provides margin for modest-bandwidth signal processing. The 14-pin SOIC exposes four channels so that two differential amplifier stages or one differential stage plus filtering and output buffers can share a package. Rail-to-rail output swing improves utilization of the available supply range. Designers should verify the input common-mode range at the lowest operating voltage and assess offset, drift, noise, and channel matching against the measurement resolution.

🖥️

Low-Voltage Interface Buffering

The MCP604T-E/SL is appropriate for buffering ADC, DAC, comparator, and sensor outputs in a low-voltage interface. Its low 230 µA typical operating current reduces loading on compact power budgets, and the 2.3 V/µs slew rate supports faster transitions than a strictly low-frequency precision amplifier. Rail-to-rail output helps preserve signal range in a 3.3 V system. The 2.8 MHz gain-bandwidth product is suitable for many general-purpose interface paths, but it is not intended for demanding wideband video or high-speed communications. Input offset, settling behavior, capacitive-load drive, and the source device’s output capability must be checked.

🚗

Automotive Low-Power Conditioning

The MCP604T-E/SL is identified as an AEC-Q100-qualified automotive low-power amplifier, making it a candidate for low-speed sensor and signal-conditioning functions. Its 230 µA typical operating current supports low-power vehicle electronics, while rail-to-rail output operation improves signal swing in 3.3 V and 5 V subsystems. The four-channel 14-pin SOIC package consolidates multiple analog functions and reduces component count. Automotive production use still requires confirmation of the exact temperature grade, qualification status, supply-chain traceability, and manufacturer-approved lifecycle expectations. Input transients, ground offsets, EMC coupling, and operating-temperature limits require system-level review.

What is the operating voltage of MCP604T-E/SL?
The MCP604T-E/SL operates from a single supply of 2.7 V to 6 V. Microchip identifies the MCP604 family as a 2.7 V minimum single-supply CMOS operational amplifier, while the product listing identifies the 6 V upper supply limit. This range supports 3.3 V and 5 V systems when the amplifier’s input common-mode and output-swing limits are acceptable at the selected voltage.
What are the key specifications of MCP604T-E/SL that engineers should know?
The MCP604T-E/SL is a four-channel CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 2.3 V/µs slew rate, 230 µA typical operating current, 1 pA bias current, and rail-to-rail output. According to the Microchip MCP604 product page, it supports single supplies as low as 2.7 V and combines low bias current with high open-loop gain in a 14-pin SOIC.
Where can I download the MCP604T-E/SL datasheet PDF?
The official MCP604T-E/SL technical information is available through the Microchip MCP604 product page at https://www.microchip.com/en-us/product/MCP604. Use the manufacturer’s datasheet and product documentation for the complete electrical characteristics, package drawing, ordering information, and recommended application circuits.
Where can I find the MCP604T-E/SL pinout?
The MCP604T-E/SL uses a 14-pin SOIC, and its numbered pin assignment and package dimensions are shown in the manufacturer’s MCP604 documentation. Use the pin-description table and package drawing on the official product page when assigning amplifier inputs, outputs, supply rails, and ground connections on the PCB.
What is the best drop-in replacement for MCP604T-E/SL?
The closest same-footprint replacements identified for the MCP604T-E/SL are MCP604T-I/SL and MCP604-I/SL, both in the MCP604 family and 14-pin SOIC format. MCP604T-I/SL changes the temperature-grade ordering code, while MCP604-I/SL differs in temperature grade and reel packaging. Confirm electrical limits, lifecycle status, and manufacturer qualification for the target environment before substitution.
Can MCP604T-I/SL replace MCP604T-E/SL?
MCP604T-I/SL is a same-brand, same-family 14-pin SOIC alternative to MCP604T-E/SL. According to the comparison information, both provide a 2.8 MHz gain-bandwidth product, a 2.7 V minimum supply, and rail-to-rail output operation. The meaningful difference is the ordering and temperature-grade code, so the exact electrical limits must be checked for the intended ambient-temperature range.
MCP604T-E/SL vs MCP604T-I/SL — which is better for an industrial design?
Choose MCP604T-E/SL or MCP604T-I/SL according to the required ambient-temperature range rather than signal performance alone. Both are MCP604-family quad amplifiers with a 2.8 MHz gain-bandwidth product in a 14-pin SOIC. The I-grade ordering code is generally intended for a different temperature class, so industrial selection should follow the manufacturer’s ordering table and the enclosure’s worst-case temperature.
When should I choose MCP604T-E/SL over MCP604-I/SL?
Choose MCP604T-E/SL when its specified temperature grade covers the product’s operating environment and the required supply and input conditions. MCP604-I/SL provides the same MCP604 family, 2.8 MHz bandwidth, and 14-pin SOIC footprint but uses a different ordering code. Use MCP604-I/SL only after confirming that its temperature limits and qualification requirements match the design.
Is MCP604T-E/SL suitable for low-voltage sensor conditioning?
The MCP604T-E/SL is suitable for many low-voltage sensor-conditioning stages because it operates from 2.7 V, provides approximately 1 pA input bias current, and uses a 2.8 MHz gain-bandwidth product. Its 230 µA typical operating current also suits portable systems. The signal source, common-mode range, sensor output level, and required noise performance must still be checked before selection.
How much current does MCP604T-E/SL consume?
The MCP604T-E/SL has a typical operating current of 230 µA, according to the Microchip MCP604 product description. This low quiescent current helps preserve battery life in portable instrumentation. Because this figure is a typical family-level value, final energy-budget calculations should use the worst-case supply-current conditions and temperature range specified for the selected device.
Is MCP604T-E/SL rail-to-rail?
The MCP604T-E/SL provides rail-to-rail output swing. The manufacturer describes the MCP604 family as having rail-to-rail output operation, low bias current, high-speed operation, and high open-loop gain. Rail-to-rail output does not mean the input common-mode range covers every point between the supply rails, so input-range requirements must be checked separately.
Where to buy MCP604T-E/SL online?
Use the Request a Quote form on this page to request MCP604T-E/SL availability, pricing, and lead time. The part is listed as a Microchip Technology four-channel CMOS amplifier in a 14-pin SOIC, and a distributor result identifies it as active. The quote team can confirm exact lot availability and manufacturer-approved sourcing without relying on static marketplace pricing.
What is the price of MCP604T-E/SL?
Pricing for MCP604T-E/SL is managed through the Request a Quote form on this page because the available listing does not provide a qualifying quantity-break schedule for this exact ordering code. Submit the required quantity, package preference, and target date, and the quote team will provide current pricing and availability for MCP604T-E/SL.
What is the lead time and stock status for MCP604T-E/SL?
Current MCP604T-E/SL stock and lead time should be requested through the Request a Quote form on this page. One product record identifies the family as active, while real-time inventory changes across channels and package quantities. Provide your required quantity and production schedule so the quote can be matched to an appropriate manufacturer-supported source.
Is MCP604T-E/SL AEC-Q100 qualified?
The MCP604T-E/SL product listing identifies the amplifier as automotive AEC-Q100 qualified. Microchip also markets the MCP604 as a low-power quad CMOS operational amplifier with a 2.8 MHz gain-bandwidth product and 230 µA typical operating current. Confirm the exact qualification documentation and temperature-grade ordering requirements for production release.
What is the best equivalent for MCP604T-E/SL in a 14-pin SOIC design?
For the same manufacturer and footprint, MCP604T-I/SL, MCP604-I/SL, MCP604-E/SL, and MCP6L04T-E/SL are the closest alternatives identified. MCP604T-I/SL preserves the MCP604 performance family; MCP6L04T-E/SL provides a related low-power quad rail-to-rail amplifier; MCP604-I/SL changes the grade and packing code. Verify input offset, bias current, bandwidth, common-mode range, and temperature limits before replacing the original part.

エンジニアリング参考データ: MCP604T-E/SL — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose MCP604T-E/SL for a low-voltage, low-power design that needs four rail-to-rail CMOS amplifiers in a 14-pin SOIC, particularly when 2.8 MHz bandwidth, 2.3 V/µs slew rate, approximately 1 pA bias current, and 230 µA typical operating current are desirable. Choose MCP604T-I/SL when that exact MCP604 family and footprint are needed but the alternate temperature-grade ordering code better matches the required operating range. Choose MCP604-I/SL when its grade and reel-packing configuration are appropriate, and choose MCP604-E/SL when its ordering code is preferable for the production environment. MCP6L04T-E/SL is the closest related-family option in the same footprint, but its input offset, bias current, slew rate, bandwidth, and temperature limits should be confirmed before substitution. For every option, verify the input common-mode range, output swing, capacitive-load stability, and exact qualification requirements against the intended circuit.

代替品との比較

パラメータ この製品 MCP604T-I/SL MCP604-I/SL MCP604-E/SL MCP6L04T-E/SL
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC
Amplifier Configuration Quad operational amplifier Quad operational amplifier Quad operational amplifier Quad operational amplifier Quad operational amplifier
Output Swing Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail

主な差別化要因

  • Four low-power amplifiers in one 14-pin SOIC (vs MCP6L04T-E/SL)
  • Very low listed input bias current for high-impedance sources (vs MCP604-E/SL)
  • Rail-to-rail output improves low-voltage signal range (vs MCP604T-I/SL)

設計ノート

Route the four amplifier channels away from switching nodes, motor traces, and high-current return paths. The approximately 1 pA bias current is valuable for high-impedance sources, but it does not eliminate susceptibility to capacitive coupling or ground potential differences. Use short feedback loops, a continuous ground reference, and input shielding where the source impedance is high or the measured signal is small.

Do not equate rail-to-rail output with a fully rail-to-rail input range. Verify the permitted input common-mode range at the lowest supply voltage, especially when the sensor output can approach ground. Also check the maximum output current, load-capacitance stability, and the settling requirements of the selected closed-loop gain before using the MCP604T-E/SL in a new circuit.

Place supply-bypass capacitance close to the package power and ground pins, and keep the return path short. The 230 µA figure is the amplifier’s typical operating current, so total power budgeting must also include bias-network current, sensor excitation, ADC references, and peripheral loads. For battery designs, calculate average consumption from the complete circuit rather than from the operational amplifier alone.

Use a standard 14-pin SOIC land pattern and observe the manufacturer’s pin numbering when assigning input and output signals. Keep analog inputs away from the package ground-adjacent return pins where routing flexibility exists, and provide adequate ground copper beneath the device. Confirm the exposed assembly and soldering requirements for the exact reel-packaging code before releasing a production footprint.

コンプライアンス情報

RoHS
Compliant
REACH
Unknown
AEC-Q100
Qualified
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The product listing identifies MCP604T-E/SL as RoHS compliant and AEC-Q100 qualified. REACH, lead-free status, halogen-free status, and conflict-minerals status are unknown.

データ検証日: 2026-11-15 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

MCP604T-E/SL datasheet MCP604T-E/SL pinout MCP604T-E/SL datasheet pdf MCP604T-E/SL specifications MCP604T-E/SL equivalent MCP604T-E/SL replacement MCP604T-E/SL cross reference MCP604T-E/SL price MCP604T-E/SL stock Microchip Technology MCP604T-E/SL MCP604T-E/SL vs MCP604T-I/SL MCP604 14-pin SOIC op amp MCP604T-E/SL low voltage sensor MCP604 2.8MHz rail-to-rail amplifier

関連部品&用語

Microchip Technology MCP604T-E/SL MCP604T-I/SL MCP604-I/SL MCP604-E/SL MCP6L04T-E/SL operational amplifier quad operational amplifier CMOS analog integrated circuit signal-conditioning electronics rail-to-rail output gain-bandwidth product slew rate input bias current input offset voltage input common-mode range 14-pin SOIC surface-mount package low-power design sensor interface active filter AEC-Q100 RoHS REACH
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示