MCP604T-E/SL - 2.8MHz Quad CMOS Op Amp | Microchip
料号: MCP604T-E/SL ✓ 量产中MCP604T-E/SL 概述
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The quad configuration provides four amplifiers in one package, reducing board area compared with four individual devices. Within the broader hierarchy of semiconductor components, the MCP604 belongs to the operational-amplifier class, analog ICs, and signal-conditioning electronics. Its low operating current makes it suitable for battery-powered equipment, instrumentation, sensor interfaces, and general-purpose analog signal paths.
The MCP604’s principal characteristics include a 2.8 MHz gain-bandwidth product, 2.3 V/µs slew rate, approximately 1 pA input bias current, and a 2 mV input-offset voltage as listed for this ordering code. Rail-to-rail output operation allows the output to approach the supply rails, improving output swing in low-voltage systems. A minimum supply of 2.7 V supports compatibility with 3.3 V system rails while retaining a typical operating current of 230 µA.
Microchip’s advanced CMOS process gives the MCP604 low bias current, high open-loop gain, and low static power requirements. The combination of a 2.8 MHz gain-bandwidth product and 2.3 V/µs slew rate supports moderate-bandwidth closed-loop amplifier configurations. Because the amplifiers are intended for low-voltage operation, input common-mode range, output swing, noise, offset, and stability should be checked against the specific gain and load conditions used in the final circuit.
Typical uses include portable sensor conditioning, low-voltage data acquisition, current-to-voltage conversion, active filtering, and general buffer or gain stages. The quad organization is particularly useful when a design needs several matched-function channels, such as two differential amplifier stages or four independent low-frequency signal conditioners. The 14-pin SOIC also supports conventional leaded-package assembly and prototype-board layouts.
When designing around the MCP604T-E/SL, place the input and output paths away from switching-node and high-current return paths to reduce coupling into the low-bias-current amplifier. Confirm the usable input and output ranges at the selected supply voltage, and verify stability with the intended source impedance, load, feedback network, and gain. Proper bypassing and a quiet ground-reference arrangement are especially important in battery-powered precision measurement systems.
直接替换替代料: MCP604T-E/SL ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MCP604T-E/SL (相同外形与封装尺寸) ——差异在于 Package, Gain-Bandwidth Product, Amplifier Type, Maximum Input Offset Voltage, Slew Rate.
MCP604T-I/SL
✅ 直接替换联系询价
查看数据手册 →MCP604-I/SL
✅ 直接替换联系询价
查看数据手册 →MCP604-E/SL
✅ 直接替换联系询价
查看数据手册 →MCP6L04T-E/SL
✅ 直接替换📋 参考替代料(不在目录中)
MCP604T-E/SL 最大额定值与电气特性
| Amplifier Type | Quad CMOS operational amplifier |
| Number of Channels | 4 channels |
| Gain-Bandwidth Product | 2.8 MHz |
| Slew Rate | 2.3 V/µs |
| Typical Operating Current | 230 µA |
| Minimum Single-Supply Voltage | 2.7 V |
| Maximum Supply Voltage | 6 V |
| Input Bias Current | 1 pA |
| Maximum Input Offset Voltage | 2 mV |
| Output Swing | Rail-to-rail |
| Process Technology | Advanced CMOS |
| Open-Loop Gain | High open-loop gain |
| 封装 | 14-pin SOIC |
| 安装类型 | Surface mount |
| Automotive Qualification | AEC-Q100 |
| RoHS 状态 | Compliant |
| 生命周期状态 | Active |
MCP604T-E/SL 14-pin soic 引脚配置指南
MCP604T-E/SL(14-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: MCP604T-E/SL.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MCP604T-E/SL 适用于 6 应用s: Portable Sensor Signal Conditioning, Battery-Powered Data Acquisition, Active Filtering and Gain Stages, Industrial Current Monitoring, Low-Voltage Interface Buffering, Automotive Low-Power Conditioning.
Portable Sensor Signal Conditioning
The MCP604T-E/SL fits portable sensor front ends that require low bias current and a small analog signal-conditioning footprint. Its approximately 1 pA input bias current minimizes loading on high-impedance sources, while the 230 µA typical operating current helps preserve battery life. The 2.8 MHz gain-bandwidth product supports low- and moderate-bandwidth gain stages. Four amplifiers can provide sensor buffering, gain, filtering, and output conditioning without requiring separate packages. Because rail-to-rail output increases available signal swing, the circuit remains useful with low-voltage sensors, although the input common-mode range must be checked at the selected supply voltage.
推荐
Battery-Powered Data Acquisition
The MCP604T-E/SL is useful in battery-powered data-acquisition systems where four conditioned channels are needed at low power. The 2.7 V minimum single-supply operation supports 3.3 V systems, and the 230 µA typical operating current reduces the amplifier’s contribution to standby consumption. Its 1 pA bias current helps when the inputs come from high-impedance sensors or leakage-sensitive dividers. The 2.8 MHz bandwidth and 2.3 V/µs slew rate accommodate modest-frequency instrumentation. Designers should still account for sensor excitation, reference accuracy, ADC input range, and the amplifier’s settling behavior in the complete acquisition chain.
推荐
Active Filtering and Gain Stages
The MCP604T-E/SL can implement the gain and active-filter stages required in low-frequency measurement chains. Its 2.8 MHz gain-bandwidth product provides useful bandwidth for precision amplifier networks, while the four channels allow a practical multi-stage filter without four separate packages. The approximately 2 mV listed input-offset voltage must be included in the error budget for low-level signals, and the 1 pA bias current is advantageous for high-impedance networks. Stable operation requires checking the feedback topology, source impedance, load capacitance, and component tolerances against the device’s stability characteristics.
推荐
Industrial Current Monitoring
The MCP604T-E/SL can amplify the small voltage produced by a current-sense element in an industrial monitoring circuit. Low input bias current helps avoid disturbing the sense path, while the 2.8 MHz gain-bandwidth product provides margin for modest-bandwidth signal processing. The 14-pin SOIC exposes four channels so that two differential amplifier stages or one differential stage plus filtering and output buffers can share a package. Rail-to-rail output swing improves utilization of the available supply range. Designers should verify the input common-mode range at the lowest operating voltage and assess offset, drift, noise, and channel matching against the measurement resolution.
推荐
Low-Voltage Interface Buffering
The MCP604T-E/SL is appropriate for buffering ADC, DAC, comparator, and sensor outputs in a low-voltage interface. Its low 230 µA typical operating current reduces loading on compact power budgets, and the 2.3 V/µs slew rate supports faster transitions than a strictly low-frequency precision amplifier. Rail-to-rail output helps preserve signal range in a 3.3 V system. The 2.8 MHz gain-bandwidth product is suitable for many general-purpose interface paths, but it is not intended for demanding wideband video or high-speed communications. Input offset, settling behavior, capacitive-load drive, and the source device’s output capability must be checked.
推荐
Automotive Low-Power Conditioning
The MCP604T-E/SL is identified as an AEC-Q100-qualified automotive low-power amplifier, making it a candidate for low-speed sensor and signal-conditioning functions. Its 230 µA typical operating current supports low-power vehicle electronics, while rail-to-rail output operation improves signal swing in 3.3 V and 5 V subsystems. The four-channel 14-pin SOIC package consolidates multiple analog functions and reduces component count. Automotive production use still requires confirmation of the exact temperature grade, qualification status, supply-chain traceability, and manufacturer-approved lifecycle expectations. Input transients, ground offsets, EMC coupling, and operating-temperature limits require system-level review.
推荐
推荐产品汇总
工程参考数据: MCP604T-E/SL ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MCP604T-I/SL | MCP604-I/SL | MCP604-E/SL | MCP6L04T-E/SL |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Amplifier Configuration | Quad operational amplifier | Quad operational amplifier | Quad operational amplifier | Quad operational amplifier | Quad operational amplifier |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
关键差异点
- Four low-power amplifiers in one 14-pin SOIC (对比 MCP6L04T-E/SL)
- Very low listed input bias current for high-impedance sources (对比 MCP604-E/SL)
- Rail-to-rail output improves low-voltage signal range (对比 MCP604T-I/SL)
设计说明
Route the four amplifier channels away from switching nodes, motor traces, and high-current return paths. The approximately 1 pA bias current is valuable for high-impedance sources, but it does not eliminate susceptibility to capacitive coupling or ground potential differences. Use short feedback loops, a continuous ground reference, and input shielding where the source impedance is high or the measured signal is small.
Do not equate rail-to-rail output with a fully rail-to-rail input range. Verify the permitted input common-mode range at the lowest supply voltage, especially when the sensor output can approach ground. Also check the maximum output current, load-capacitance stability, and the settling requirements of the selected closed-loop gain before using the MCP604T-E/SL in a new circuit.
Place supply-bypass capacitance close to the package power and ground pins, and keep the return path short. The 230 µA figure is the amplifier’s typical operating current, so total power budgeting must also include bias-network current, sensor excitation, ADC references, and peripheral loads. For battery designs, calculate average consumption from the complete circuit rather than from the operational amplifier alone.
Use a standard 14-pin SOIC land pattern and observe the manufacturer’s pin numbering when assigning input and output signals. Keep analog inputs away from the package ground-adjacent return pins where routing flexibility exists, and provide adequate ground copper beneath the device. Confirm the exposed assembly and soldering requirements for the exact reel-packaging code before releasing a production footprint.
合规信息
The product listing identifies MCP604T-E/SL as RoHS compliant and AEC-Q100 qualified. REACH, lead-free status, halogen-free status, and conflict-minerals status are unknown.