MCP606-I/P - 155kHz Micropower Op Amp | Microchip
部品番号: MCP606-I/P ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
ドロップイン代替品: MCP606-I/P — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MCP606-I/P （同一形状・フットプリント） — 相違点: Input Bias Current, Output Swing, Product Type, Typical Operating Current.
クイック比較ツール — 並列比較する代替部品を選択:
MCP606T-I/P
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MCP606-I/OT
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MCP606-I/ST
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MCP606T-I/ST
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MCP606T-I/SN
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MCP606-I/P 最大定格＆電気的特性
| Product Type | Single operational amplifier |
| Technology | Advanced CMOS |
| Number of Channels | 1 channel |
| Gain Bandwidth Product | 155 kHz |
| Typical Operating Current | 18.7 uA |
| Maximum Offset Voltage | 250 uV |
| Supply Voltage Range | 2.5 V to 6.0 V |
| Input Bias Current | 80 pA maximum at +85 C |
| Output Swing | Rail-to-rail |
| Unity-Gain Stability | Yes |
| パッケージ | 8-pin PDIP |
| Package Type | Through-hole PDIP |
MCP606-I/P through-hole pdip ピン配置ガイド
MCP606-I/P (through-hole pdip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: MCP606-I/P.
詳細は データシート をご参照ください。
主な用途
MCP606-I/P の用途: 6 件s: Battery-Powered Sensor Interface, Portable Measurement Front End, Low-Voltage Signal Buffer, Portable Instrumentation, Low-Voltage Control Signal Conditioning, Portable Analog Signal Conditioning.
Battery-Powered Sensor Interface
The MCP606-I/P fits battery-powered sensor interfaces because it operates from 2.5 V to 6.0 V and has a typical operating current of 18.7 uA. Its 155 kHz gain-bandwidth product is appropriate for slow sensor signals, while rail-to-rail output swing helps use the available supply range. Place the amplifier close to the sensor output and use the 8-pin PDIP package only when through-hole assembly is acceptable. Verify the sensor’s output range, input common-mode limits, required noise performance, and stability with the selected gain before production release.
おすすめ
Portable Measurement Front End
The MCP606-I/P is suitable for portable measurement front ends that amplify weak, low-frequency analog signals under a constrained power budget. The 18.7 uA typical operating current supports battery life, and the 155 kHz gain-bandwidth product provides more than enough bandwidth for many temperature, pressure, and resistance-sensor signals. Its rail-to-rail output can improve usable dynamic range in a low-voltage system. Check offset accuracy, input bias current, noise, and common-mode behavior against the sensor and instrumentation requirements rather than assuming general-purpose specifications are sufficient.
おすすめ
Low-Voltage Signal Buffer
Use the MCP606-I/P as a unity-gain buffer when a sensor or divider must drive a downstream ADC without loading the source. The family is unity-gain stable and has a 155 kHz gain-bandwidth product, which is suitable for many low-frequency buffering tasks. Rail-to-rail output swing can preserve signal range in compact systems, while the 18.7 uA typical current helps limit power use. Confirm output load, capacitive loading, settling requirements, input offset, and the ADC’s acquisition behavior with the manufacturer’s application guidance.
おすすめ
Portable Instrumentation
The MCP606-I/P can support portable instrumentation requiring modest bandwidth and low supply current. Its 2.5 V minimum supply voltage is helpful for single-cell or reduced-voltage systems, and the 155 kHz gain-bandwidth product is adequate for many sensor, control, and analog monitoring functions. The rail-to-rail output swing helps maximize signal excursion in a constrained enclosure. Designers should still evaluate input-referred noise, offset drift, common-mode range, output drive, and temperature stability for precision measurement specifications.
おすすめ
Low-Voltage Control Signal Conditioning
The MCP606-I/P is appropriate for conditioning low-voltage control signals in battery-operated equipment, provided the control bandwidth is modest. Its typical 18.7 uA current and 155 kHz gain-bandwidth product support efficient analog amplification without introducing a high-speed, high-power architecture. The 2.5 V to 6.0 V operating range aligns with low-voltage control rails. For actuator or feedback loops, verify stability, output drive, noise, and propagation requirements; the basic family specification is not a substitute for a complete control-loop design.
おすすめ
Portable Analog Signal Conditioning
The MCP606-I/P can serve as a general analog signal-conditioning element in portable products such as compact meters, handheld testers, and wearable-adjacent sensing modules. Its single-channel 155 kHz architecture is suited to low-frequency amplification and buffering, while 18.7 uA typical operating current supports power-conscious designs. The rail-to-rail output is valuable when the downstream converter or ADC has a narrow usable signal window. Validate input common-mode range, offset stability, noise, and PCB leakage before using it for high-impedance sources.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MCP606-I/P — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MCP606T-I/P | MCP606-I/OT | MCP606-I/ST | MCP606T-I/ST |
|---|---|---|---|---|---|
| Product Type | Single micropower CMOS operational amplifier | MCP606-family operational amplifier | MCP606-family operational amplifier | MCP606-family operational amplifier | MCP606-family operational amplifier |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
主な差別化要因
- Low-power single-channel CMOS operation （vs MCP606T-I/P)
- Low-voltage operation with rail-to-rail output （vs MCP606-I/OT)
- Single-channel PDIP format for through-hole assembly （vs MCP606-I/ST)
設計ノート
Estimated: the MCP606-I/P’s typical operating current is 18.7 uA. For a design operating at 3.0 V, the estimated device supply power is 3.0 V × 18.7 uA = 56.1 uW before considering external-load current, bias-current effects, and dynamic operation. Use the datasheet maximum-current conditions for battery-life calculations rather than treating this typical estimate as a worst-case value.
Place the op amp, input-source connection, feedback components, and decoupling capacitor close together to minimize parasitic resistance and capacitance. Keep high-impedance input traces short and shield them from switching nodes and high-current return paths. Because the verified data confirms an 8-pin PDIP package, follow the exact manufacturer pinout and package outline; the supplied data did not include a complete pin assignment, so do not infer pin numbers from package conventions.
Do not assume rail-to-rail output swing means rail-to-rail input capability. The supplied verified data explicitly confirms rail-to-rail output behavior but does not establish the full input common-mode range, output-load limits, noise, or absolute maximum ratings. Check those conditions in the manufacturer datasheet before connecting a sensor output near either supply rail, driving a heavy load, or operating at the maximum stated 6.0 V supply.
コンプライアンス情報
Compliance status was not included in the verified web data. Check the current Microchip product documentation and applicable supplier declarations before production release.