MPC885VR133 - 133MHz PowerQUICC MPU 32-Bit | NXP | Networking
部品番号: MPC885VR133 ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $48.5 | $48.50 |
| 10 | $42 | $420.00 |
| 100 | $35.75 | $3,575.00 |
| 500 | $30.2 | $15,100.00 |
| 1,000 | $27.4 | $27,400.00 |
MPC885VR133 概要
What is a PowerQUICC processor? A PowerQUICC (pronounced "powerquick") is a family of communications processors built on Power Architecture technology that combines a general-purpose embedded CPU with a separate, dedicated RISC engine - the CPM - to handle low-level networking and serial communications tasks. In the system hierarchy, the MPC885 family sits at the intersection of MPU (microprocessor unit), embedded processor, and communications controller, superseding older Motorola 68k designs for routers, switches, and industrial control. The CPM off-loads DMA, HDLC, ATM, Ethernet, USB, and serial protocols from the host CPU, freeing the core for application and management-plane code.
Key features include CPU frequencies of 66/80/133 MHz, 32-bit data bus width, integrated peripheral interfaces (Ethernet, USB, serial, I2C, SPI), 4.9W typical power dissipation, and parallel I/O via the 357-PBGA footprint. The MPC885VR133 variant excludes the LCD controller present on the MPC885 (the "V" suffix denotes reduced peripheral set versus "C" full-featured; the "R" denotes tape-and-reel packaging).
Architecturally, the device combines the MPC8xx core with the CPM, two independently programmable 8 KB caches, dual 10/100 Ethernet MACs, USB 1.1, and an industrial memory controller supporting DRAM, SDRAM, ROM/Flash, and EDO. The on-chip security engine supports DES, 3DES, AES, MD-5, and SHA-1 for VPN/IPsec offload.
Typical applications include industrial routers, telecom equipment, network switches, and embedded communications controllers. The MPC885VR133 suits designs requiring low-power operation, integrated Ethernet switching, and cryptographic offload. Consider the MPC880VR133 (without crypto) or MPC885CVR133 (with LCD controller) for variants in the same 357-PBGA footprint.
When designing in the MPC885VR133, ensure the power supply sequencing meets the core/IO rail requirements and place decoupling capacitors close to the PBGA balls. The 357-BGA package demands multilayer PCB with controlled-impedance traces; consider thermal vias below the die for continuous high-duty operation.
This page synthesizes distributor pricing, lifecycle status, drop-in alternatives from the same PowerQUICC family, and practical design notes not found in the manufacturer datasheet. Pricing and availability reference current date 2026-10-16.
ドロップイン代替品: MPC885VR133 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MPC885VR133 （同一形状・フットプリント） — 相違点: Core Architecture, Operating Temperature, Package, Family, Manufacturer.
クイック比較ツール — 並列比較する代替部品を選択:
MPC880VR133
✅ ドロップイン✓ 在庫あり
$19.45 / 個
データシートを見る →MPC885CVR133
✅ ドロップイン✓ 在庫あり
$37.95 / 個
データシートを見る →MPC866PVR133A
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MPC880ZP133
✅ ドロップイン✓ 在庫あり
$26.1 / 個
データシートを見る →MPC885ZP80
✅ ドロップイン✓ 在庫あり
$25.85 / 個
データシートを見る →MPC885VR133 最大定格＆電気的特性
| Manufacturer | NXP Semiconductors (formerly Freescale Semiconductor, originally Motorola) |
| Series | MPC8xx / PowerQUICC |
| Core Architecture | MPC8xx (Power Architecture) |
| Core Count | 1 Core |
| データバス幅 | 32-Bit |
| 最大クロック周波数 | 133 MHz |
| Performance | 176 MIPS |
| Instruction Cache | 8 KB |
| Data Cache | 8 KB |
| External Bus Frequency (Max) | 80 MHz |
| パッケージ | 357-PBGA (25 mm x 25 mm) |
| 実装タイプ | Surface Mount (BGA) |
| 動作温度範囲 | 0C to +95C |
| 電源電圧 | 3.3 V (core and I/O) |
| Ethernet Interfaces | 2x 10/100 Fast Ethernet MAC |
| USB Interface | USB 1.1 (Function or Host) |
| LCD Controller | Not present (V variant - reduced peripherals) |
| Security Engine | DES / 3DES / AES / MD-5 / SHA-1 |
| ライフサイクル状態 | End of Life (EOL); see NXP PCN for replacement options |
MPC885VR133 357-pbga (25 mm x 25 mm) ピン配置ガイド
MPC885VR133 (357-pbga (25 mm x 25 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: MPC885VR133.
詳細は データシート をご参照ください。
主な用途
MPC885VR133 の用途: 6 件s: Industrial Ethernet Router, Telecom Switch / Access Equipment, Industrial Control / SCADA Gateway, Network-Attached Storage (NAS) Controller, Voice-over-IP (VoIP) Gateway, Secure VPN Appliance.
Industrial Ethernet Router
The MPC885VR133 fits industrial Ethernet routers because its 133 MHz Power Architecture core and integrated dual 10/100 Ethernet MACs deliver the packet throughput required for SOHO and small-business routing while the hardware security engine (DES, 3DES, AES, MD-5, SHA-1) off-loads VPN/IPsec and SSL/TLS handshakes. The 357-PBGA package integrates two Ethernet ports, USB, serial, and JTAG into a single PCB footprint, reducing BOM for SOHO routers. At 133 MHz the part sustains about 176 MIPS for the routing stack, QoS, firewall rules, and management UI, while the dedicated CPM handles DMA and frame processing off-load from the host CPU. Estimated: 4-5W typical power at full Ethernet load. Choose this part versus a microcontroller when deterministic DMA and proven VPN throughput are needed.
おすすめ
Telecom Switch / Access Equipment
In telecom access equipment, the MPC885VR133's CPM handles HDLC, ATM, TDM, and serial protocols off-loaded from the core, freeing the Power Architecture CPU for call processing, signaling, or management-plane code. The 357-PBGA package exposes two Ethernet MACs, USB, I2C, SPI, and dual UART to support T1/E1 framer interfaces, MDIO for PHY management, and serial console access. 8 KB instruction + 8 KB data caches plus the external 80 MHz bus allow the host CPU to drive protocol stacks at typical telco load. Estimated: 3-4W power for idle line card. The 0-95C temperature grade suits indoor telecom closet deployments but not outdoor cabinets without additional conformal coating.
おすすめ
Industrial Control / SCADA Gateway
The MPC885VR133 is well suited as a SCADA gateway controller: two Ethernet MACs bridge field buses (Modbus TCP, EtherNet/IP) and serial (Modbus RTU on UART), while the Power Architecture core runs local control logic in C/C++. The on-chip memory controller supports SDRAM/EDO/Flash for deterministic boot and runtime, and the 357-PBGA 25x25 mm footprint fits standard mini-ITX module designs. The 0-95C commercial/industrial operating range covers plant-floor cabinets. Estimated: 1-2W at light load without VPN. Designers integrating HMI panels should consider the MPC885CVR133 variant for LCD controller support.
おすすめ
Network-Attached Storage (NAS) Controller
As a NAS/SAN controller core, the MPC885VR133's CPM provides dual 10/100 Ethernet ports for redundant link or bonded-LACP configurations while the host core runs filesystem stacks (ext4, SMB, NFS). The on-chip security engine accelerates SMB signing without consuming CPU cycles, important for multi-user file-serving throughput. The 357-PBGA package is suitable for mezzanine add-in boards that pair the MPU with external SATA bridge chips. Estimated performance penalty at lower 80 MHz bus. Choose this over a generic ARM SoC when you require deterministic interrupt response for I/O.
おすすめ
Voice-over-IP (VoIP) Gateway
The MPC885VR133 fits small-business VoIP gateways where the CPM off-loads voice packet handling (RTP/RTCP, HDLC over T1/E1) and the host CPU runs SIP/RTP signaling stacks. The hardware security engine accelerates SRTP/TLS key exchange on encrypted trunks. Two Ethernet MACs separate WAN and LAN sides; integrated USB 1.1 hosts IP phones or expansion modules. Estimated: ~5W at full bidirectional voice call load. Use the MPC880VR133 cost-down variant for endpoints with no encryption requirements.
おすすめ
Secure VPN Appliance
The MPC885VR133 is ideal for entry-level VPN appliances where its hardware crypto engine handles DES/3DES/AES at line rates that a pure-software CPU cannot sustain, while the CPM manages frame DMA and the host core enforces firewall rules and policy. Per NXP documentation, the integrated security engine off-loads IPsec ESP/AH and SSL/TLS bulk crypto so the 133 MHz host core can dedicate cycles to inspection, NAT, and routing. The 357-PBGA package is acceptable for fanless sealed enclosures using a heatsink above the die. Estimated performance: ~80 Mbps 3DES throughput with the engine enabled, dropping to ~15 Mbps in software-only mode.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MPC885VR133 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MPC880VR133 | MPC885CVR133 | MPC866PVR133A | MPC880ZP133 | MPC885ZP80 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 357-PBGA (25x25 mm) | 357-PBGA (25x25 mm) - same | 357-PBGA (25x25 mm) - same | 357-PBGA (25x25 mm) - same | 357-PBGA (25x25 mm) - same | 357-PBGA (25x25 mm) - same |
| Core Clock Frequency | 133 MHz | 133 MHz | 133 MHz | 133 MHz | 133 MHz | 80 MHz (-40%) |
| Security Engine | Yes (DES/3DES/AES/MD-5/SHA-1) | No | Yes | Yes | No | Yes |
| LCD Controller | No (V-variant) | No | Yes | No | No | No |
| Ethernet MACs | 2x 10/100 | 0 (none) | 2x 10/100 | 2x 10/100 | 0 (none) | 2x 10/100 |
| Performance | 176 MIPS | 176 MIPS | 176 MIPS | ~176 MIPS (variable) | 176 MIPS | ~106 MIPS |
| Operating Temperature | 0C to +95C | 0C to +95C | 0C to +95C | 0C to +95C | -40C to +85C (Z-extended) | -40C to +85C (Z-extended) |
主な差別化要因
- Reduced peripheral set cost-down （vs MPC885CVR133)
- Integrated hardware security engine included （vs MPC880VR133)
- Dual integrated Ethernet MACs （vs MPC880VR133)
- Higher clock than ZP80 variant （vs MPC885ZP80)
- Lower pin compatibility overhead vs PowerPC successors （vs MPC866PVR133A)
設計ノート
The MPC885VR133 in the 357-PBGA package dissipates an estimated 4-5W at full Ethernet and crypto load. At 95C ambient, the junction-to-ambient thermal resistance (theta_JA) for a standard 4-layer JEDEC test board is approximately 15-20 C/W for this large PBGA - confirmed placement of thermal vias (staggered 1.2 mm pitch, 0.3 mm drill, filled) below the die shadow is critical. Estimated: without thermal vias, the junction can rise 60-80C above ambient at 4W dissipation. Recommend a stiffener or aluminum heat-spreader for sealed fanless enclosures.
Use 8-layer PCB stack-up with dedicated power and ground planes for the 357-PBGA footprint. Route all 50 ohm and 75 ohm impedance traces (Ethernet, USB) with reference to the unbroken ground plane on an adjacent layer. Apply via-in-pad micro-vias (0.1 mm pitch capable) under the BGA balls where available from your fabricator. Decoupling: place 100 nF X7R capacitors at every 3rd BGA ball adjacent to power pins, and bulk 10 uF tantalum or ceramic at the PCB edges nearest the regulator.
The MPC885VR133 (V-variant) lacks the LCD controller present on the C-series - firmware written for the C-variant will fail to initialize video on this part. Conversely, the MPC880VR133 omits the security engine - IPsec/SSL code paths that call hardware crypto APIs will silently fall back to slow software routines and bottleneck throughput. Verify peripheral enable bits at startup, and never assume the security engine is present without checking the part number suffix.
Series-terminate the external memory bus with 22-33 ohm resistors near the MPU, matched to the trace impedance, to avoid ringback on the 80 MHz SDRAM interface. Keep MII/GMII traces between the MPU and Ethernet PHYs length-matched within 50 mil to prevent skew at 25 MHz MII or 125 MHz GMII. Use series common-mode chokes on the differential pairs (Ethernet, USB) and verify SDD21 attenuation meets the PHY's published requirements.
Core and I/O rails are typically 3.3V; bring up the core rail first and let the MPU's POR cycle complete before driving the I/O rail. Add a 4.7 ohm ferrite on each rail to filter switching noise from the CPM. The CPM's DMA engine can cause 200-400 mA transients on VCC under heavy packet load - bulk capacitance near the regulator must absorb these without sagging below the datasheet minimum.
コンプライアンス情報
RoHS/lead-free status listed as 'Details' on DigChip, not extracted verbatim. NXP officially EOL'd this part; refer to the NXP PCN for specific compliance claims. AEC-Q100 not applicable for industrial MPU.
