MSP430I2020TPW - 16MHz 24-Bit Metering MCU | Texas Instruments
部品番号: MSP430I2020TPW ✓ 生産中MSP430I2020TPW 概要
A mixed-signal microcontroller is a semiconductor that combines a digital processing core with analog measurement functions. Within the product hierarchy, the MSP430I2020 is a mixed-signal MCU, part of the MSP430 family and the broader power-management and metering ecosystem. Its sigma-delta ADC channels are intended to measure slowly varying or multiplexed analog signals accurately while keeping the external analog signal chain compact. This integration reduces component count compared with separate MCU and ADC designs.
The headline features are a 16.384 MHz maximum listed clock, 24-bit ADC resolution on two channels, 16 KB Flash, 1 KB RAM, and a 28-pin TSSOP package. Two 16-bit timers support timing, sampling, modulation, and periodic measurement tasks. According to the Texas Instruments MSP430I2020 product page, the device operates from 2.5 V or 3.3 V and is specified for an industrial temperature range of -40 °C to 105 °C.
The MSP430 CPU16 architecture uses a reduced instruction set and a 16-bit register model optimized for low-power embedded control. Sigma-delta ADCs trade conversion speed for high resolution and noise performance, making the device appropriate for metering rather than high-speed waveform capture. The MSP430I2020 family shares an established hardware and software ecosystem, including the EVM430-I2040S evaluation module and the MSP-TS430RHB32A target board identified by Texas Instruments.
Typical applications include single-phase energy meters, smart-grid sensing nodes, industrial power monitors, current-and-voltage measurement boards, low-cost isolated data loggers, and compact sensor-hub products. The two ADC channels can be paired with suitable current and voltage front ends, while the timers coordinate sampling and communications. Firmware selection, calibration strategy, and external signal-conditioning components remain central to achieving useful metering accuracy.
For a new design, begin with the MSP430I2020 datasheet pin-description table, the MSP430I2xx User Guide, and the applicable metering reference design. Check analog input ranges, exposed ground connections, debugger access, and decoupling requirements against the selected board architecture. Do not treat a family member with a different ADC-channel count as an automatic replacement without reviewing its pinout and firmware requirements.
This page combines the manufacturer specifications, package details, family alternatives, application guidance, and engineering-focused selection notes needed to evaluate the MSP430I2020TPW for embedded metering and monitoring designs.
ドロップイン代替品: MSP430I2020TPW — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MSP430I2020TPW (同一形状・フットプリント) — 相違点: Flash Memory, RAM, Package, ADC Architecture, ADC Resolution.
MSP430I2021TPW
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MSP430I2022TPW
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MSP430I2031TPWR
✅ ドロップイン価格はお問い合わせください
データシートを見る →MSP430I2041TPW
✅ ドロップイン価格はお問い合わせください
データシートを見る →MSP430I2020TPW 最大定格&電気的特性
| Product Type | Mixed-signal metering microcontroller |
| CPU Architecture | MSP430 CPU16, 16-bit RISC |
| 最大クロック周波数 | 16.384 MHz |
| ADC Architecture | 2-channel sigma-delta ADC |
| ADC Resolution | 24-bit per channel |
| Timer Count | 2 timers, 16-bit each |
| Flash Memory | 16 KB |
| RAM | 1 KB |
| 電源電圧 | 2.5 V or 3.3 V |
| 動作温度 | -40 °C to 105 °C |
| パッケージ | 28-pin TSSOP (PW) |
| Terminal Count | 28 pins |
| 実装タイプ | Surface mount |
| Device Family | MSP430I2xx metering MCU family |
MSP430I2020TPW 28-pin tssop (pw) ピン配置ガイド
MSP430I2020TPW (28-pin tssop (pw) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: MSP430I2020TPW.
詳細は データシート をご参照ください。
主な用途
MSP430I2020TPW の用途: 6 件s: Single-Phase Smart Energy Meter, Industrial Power-Monitoring Terminal, Smart-Grid Sensor Node, Battery-Powered Sensor Hub, Compact Data-Acquisition Module, Precision Low-Power Instrument.
Single-Phase Smart Energy Meter
MSP430I2020TPW fits a single-phase energy-meter architecture where the meter must measure two analog quantities, such as voltage and current. Its two 24-bit sigma-delta ADC channels provide the resolution needed for compensated energy calculations, while two 16-bit timers can organize sampling and accumulation intervals. The 16 KB Flash supports metering firmware, calibration tables, and communication routines, and the 1 KB RAM accommodates working state. Use isolated current and voltage sensing front ends, a suitably referenced analog section, and an external communications interface as required by the meter architecture.
おすすめ
Industrial Power-Monitoring Terminal
The MSP430I2020TPW can serve as the control center of a compact industrial power-monitoring terminal. Two 24-bit sigma-delta channels can acquire voltage and current-related sensor outputs, while the 16.384 MHz MSP430 CPU16 handles filtering, scaling, threshold evaluation, and event reporting. Two 16-bit timers support periodic measurements without blocking the main control flow. The industrial -40 °C to 105 °C rating and 2.5 V or 3.3 V operation suit equipment designed for factory and building environments, although an industrial enclosure must provide the required isolation and environmental protection.
おすすめ
Smart-Grid Sensor Node
MSP430I2020TPW is appropriate for a compact smart-grid sensing node that measures two analog channels and performs local calculations before transmitting results. The MSP430 architecture supports low-power operation, and the two 24-bit sigma-delta ADCs are well matched to voltage and current sensing rather than high-speed waveform acquisition. Two timers can establish accurate sampling schedules, while 16 KB Flash holds protocol and calibration code. Pair the MCU with isolated sensing hardware and a communications module when the node must interface with utility or building-management infrastructure.
おすすめ
Battery-Powered Sensor Hub
A battery-powered environmental or industrial sensor hub can use MSP430I2020TPW when two analog inputs provide sufficient measurement capacity and 16 KB Flash is adequate for embedded control. The low-power MSP430 CPU16 can remain inactive between measurements, while the two 16-bit timers trigger periodic sampling. The 24-bit ADC resolution can improve the usable dynamic range of resistive, current-output, or temperature-derived sensor signals. Power-budget calculations should include sensor standby current, analog bias current, regulator quiescent current, and radio duty cycle because the MCU alone does not determine the complete battery life.
おすすめ
Compact Data-Acquisition Module
MSP430I2020TPW can form the core of a compact two-channel data-acquisition module for slowly varying process signals. The 24-bit sigma-delta converters provide high nominal resolution, while the MSP430 CPU16 performs scaling, offset correction, filtering, and timestamped control. Two 16-bit timers allow accurate periodic acquisition without excessive polling overhead, and the 16 KB Flash and 1 KB RAM support a focused embedded application. Signal bandwidth, input range, common-mode voltage, and isolation must be assessed because high ADC resolution does not by itself guarantee accuracy for fast or high-voltage inputs.
おすすめ
Precision Low-Power Instrument
MSP430I2020TPW suits a precision instrument that combines measurement, control, and a limited local display interface. Two high-resolution ADC channels can acquire sensor outputs, while the timers support periodic sampling and calibration routines. The microcontroller's 16 KB Flash can hold a dedicated control application and compensation coefficients, and its 1 KB RAM is sufficient for focused state handling. For instrumentation applications, pay particular attention to analog-reference stability, grounding, calibration storage, display-driver timing, and the distinction between ADC resolution and the uncertainty of the complete measurement chain.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MSP430I2020TPW — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MSP430I2021TPW | MSP430I2022TPW | MSP430I2031TPW | MSP430I2041TPW |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin TSSOP (PW) | 28-pin TSSOP (PW) | 28-pin TSSOP (PW) | 28-pin TSSOP (PW) | 28-pin TSSOP (PW) |
| ADC Channel Count | 2 channels | 1 channel | 2 channels | 3 channels | 4 channels |
| ADC Resolution | 24-bit | 24-bit | 24-bit | 24-bit | 24-bit |
| Maximum Clock Frequency | 16.384 MHz | 16.384 MHz | 16.384 MHz | 16.384 MHz | 16.384 MHz |
| Timer Count | 2 timers, 16-bit each | 2 timers, 16-bit each | 2 timers, 16-bit each | 2 timers, 16-bit each | 2 timers, 16-bit each |
| Supply Voltage | 2.5 V or 3.3 V | 2.5 V or 3.3 V | 2.5 V or 3.3 V | 2.5 V or 3.3 V | 2.5 V or 3.3 V |
| Operating Temperature | -40 °C to 105 °C | -40 °C to 105 °C | -40 °C to 105 °C | -40 °C to 105 °C | -40 °C to 105 °C |
主な差別化要因
- Two-channel 24-bit metering AFE (vs MSP430I2021TPW)
- Lower channel count than the I203x family (vs MSP430I2031TPW)
- Half the ADC channel count of the I204x family (vs MSP430I2041TPW)
設計ノート
Route analog inputs as short, guarded traces away from switching nodes, high-current conductors, and digital communication lines. Keep the analog ground, digital ground, and exposed package ground connections consistent with the manufacturer layout guidance. Place input filtering and protection components close to the source and MCU pins so their parasitics are included in the simulated signal path. Verify every analog and supply pin against the PW package drawing before releasing PCB artwork.
Do not select a family member solely from its 28-pin TSSOP package. MSP430I2021, I2022, I2031, and I2041 options differ in ADC-channel count, which can change analog routing, calibration, and firmware behavior. Confirm the exact pinout, timer resources, memory configuration, supply requirements, and peripheral assignments in the family data sheet. Treat a software migration and board review as mandatory parts of any substitution.
Budget the complete power path rather than the MCU core alone. Include sensor excitation, analog bias, ADC circuitry, regulators, communications, and output drivers when estimating battery life. Place low-ESR decoupling capacitors close to the supply pins and follow the manufacturer recommendation for bulk capacitance. Check startup, settling, and supply ripple behavior across the intended 2.5 V or 3.3 V operating condition.
Sigma-delta resolution is not the same as end-to-end measurement accuracy. Establish the input range, source impedance, antialiasing filter, reference voltage, gain, offset, and calibration method before setting the expected resolution. Use the periodic timers to define repeatable acquisition windows and reject or compensate mains-related interference. Validate accuracy at the actual signal bandwidth and temperature range used by the finished product.
コンプライアンス情報
The industrial -40 °C to 105 °C temperature specification is documented, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified. Verify current compliance documentation for the exact ordering code before regulatory submission.