OPA251UA - 15V MicroPower Rail-to-Rail Op Amp | Texas Instruments
部品番号: OPA251UA ✓ 生産中OPA251UA 概要
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. Within the product hierarchy, the OPA251UA is a voltage-feedback operational amplifier, a general-purpose amplifier IC, and a member of the wider power-management and analog signal-processing category. Rail-to-rail output swing allows the output to approach the supply rails more closely than a conventional non-rail-to-rail output stage, which is useful when a downstream circuit must operate over most of the available supply voltage.
The OPA251 family is specifically designed for battery-powered and portable applications. Its approximately 25 uA quiescent current reduces the standing power requirement of continuously powered systems. The OPA251UA combines that low-power behavior with rail-to-rail output, low offset voltage, high common-mode rejection, and high open-loop gain. These characteristics support accurate amplification of small signals while helping reduce supply-related errors and limiting current consumption in battery-operated equipment.
The OPA251UA is a single op amp in an 8-pin SOIC package, allowing a direct replacement path from the multi-amplifier OPA2251 and OPA4251 families when only one amplifier channel is required. Its approximately 35 kHz gain-bandwidth behavior, as identified in the product listing, is appropriate for low-frequency signal conditioning rather than high-speed waveform or video amplification. Users should select an amplifier with wider bandwidth when slew rate, settling time, or high-frequency signal fidelity are the dominant requirements.
Typical uses include low-power sensor conditioning, portable measurement equipment, battery-operated monitors, audio and communication interfaces, and low-current analog control systems. The device can amplify signals from low-frequency transducers while its low quiescent current helps preserve battery life. Rail-to-rail output also increases usable output range, although input common-mode limits, output swing under load, noise, and offset must still be checked against the signal chain requirements.
For a new single-supply design, place the decoupling capacitor close to the supply pins and route the feedback network to minimize parasitic pickup. Do not assume rail-to-rail output means the output can reach either rail exactly; check the datasheet output-swing conditions and the load current. If the selected manufacturer documentation does not specify exact pin names or limits, use the OPA251 data sheet as the controlling design reference.
This page organizes the OPA251UA product identity, package information, technical gaps, sourcing workflow, and engineering considerations into one practical reference. It is intended to help designers confirm device suitability, plan the PCB footprint, and identify the technical parameters that must be verified before production release.
ドロップイン代替品: OPA251UA — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストOPA251UA 最大定格&電気的特性
| Amplifier Type | Single general-purpose operational amplifier |
| Number of Channels | 1 channel |
| Supply Type | Single supply |
| Maximum Supply Voltage | 15 V |
| 静止電流 | 25 uA |
| Gain-Bandwidth Product | 35 kHz |
| Output Swing | Rail-to-rail |
| 動作温度範囲 | -40 C to 85 C |
| パッケージ | 8-pin SOIC |
| 実装タイプ | Surface mount |
| Lead-Free Status | Lead-free |
| RoHS ステータス | RoHS-compliant |
OPA251UA 8-pin soic ピン配置ガイド
OPA251UA (8-pin soic パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: OPA251UA.
詳細は データシート をご参照ください。
主な用途
OPA251UA の用途: 6 件s: Battery-Powered Sensor Signal Conditioning, Portable Medical Monitoring, Industrial Sensor Interface, Portable Measurement Instrument, Battery-Operated Communications Interface, Low-Power Audio Interface.
Battery-Powered Sensor Signal Conditioning
The OPA251UA fits low-power sensor signal conditioning because its approximately 25 uA quiescent current limits standing consumption while its rail-to-rail output provides useful range in a compact low-voltage system. Place the amplifier close to the sensor output and use the manufacturer's recommended bypass capacitor at the supply pins. The approximately 35 kHz gain-bandwidth product is suitable for slow sensor signals, although offset accuracy, input common-mode range, and output swing must be checked against the transducer's operating range.
Portable Medical Monitoring
The OPA251UA is suitable for low-frequency instrumentation in portable monitoring equipment where a 15 V maximum single supply and approximately 25 uA quiescent current are useful constraints. It can condition a transducer output before conversion or control circuitry, with rail-to-rail output allowing a wider usable signal span than a conventional output stage. For patient-connected designs, complete electrical isolation, leakage, protection, and regulatory validation remain system-level requirements and must not be inferred from the amplifier status.
Industrial Sensor Interface
The OPA251UA can amplify low-bandwidth industrial sensor signals in a 24 V-derived control system after suitable voltage conditioning reduces the supply to the amplifier's permitted range. Its rail-to-rail output and low offset characteristics are useful when the downstream converter accepts a near-supply-range input. Keep the amplifier outside the high-energy sensor wiring path or add appropriate protection, and verify common-mode limits because industrial transducers may exceed the OPA251 input range even when their signal frequency is low.
Portable Measurement Instrument
The OPA251UA supports portable measurement instruments that combine a low-level analog input with restricted power budgets. Approximately 25 uA quiescent current helps limit amplifier overhead, while the single-amplifier 8-pin SOIC format avoids allocating a multi-channel package when only one conditioning channel is needed. Its approximately 35 kHz gain-bandwidth product accommodates slow process variables and sensor outputs, but the front end must remain within the input common-mode range and account for offset and noise during calibration.
Battery-Operated Communications Interface
The OPA251UA can support low-frequency communications-interface signal paths in battery-operated equipment when channel bandwidth remains modest. Rail-to-rail output helps use the available supply range, and the low quiescent current is valuable when the interface remains enabled continuously. Keep the amplifier outside high-speed RF paths because the approximately 35 kHz gain-bandwidth product is not intended for wideband carrier processing. Confirm that coupling, filtering, and level-shift requirements preserve the amplifier's common-mode and output-swing limits.
Low-Power Audio Interface
The OPA251UA can support low-frequency audio buffering, monitoring, or auxiliary interface circuits where a micro-power amplifier is preferred. Its approximately 25 uA quiescent current and rail-to-rail output suit compact battery-powered products, while low offset and high common-mode rejection help preserve small signals. The approximately 35 kHz gain-bandwidth product limits how much high-frequency audio content the stage can amplify cleanly, so this device is better suited to monitoring and control paths than full-bandwidth line outputs.
エンジニアリング参考データ: OPA251UA — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Package | 8-pin SOIC |
| Brand | Texas Instruments |
| Amplifier Type | Single general-purpose operational amplifier |
| Maximum Supply Voltage | 15 V |
| Quiescent Current | 25 uA |
| Gain-Bandwidth Product | 35 kHz |
| Output Swing | Rail-to-rail |
| Operating Temperature Range | -40 C to 85 C |
主な差別化要因
- Low-power single-amplifier configuration (vs OPA251UA/2K5)
- Useful output range from a single supply (vs OPA251UA/2K5)
- Compact package for one-channel designs (vs OPA251UA/2K5)
設計ノート
Place the supply bypass capacitor directly between the OPA251UA supply and ground pins, following the connection shown in the manufacturer data sheet. Keep the loop short and route it away from high-current switching nodes. Because the amplifier is designed around approximately 25 uA quiescent current, also account for load current in the rail budget; low standby consumption does not prevent output-stage dissipation when the output is heavily loaded.
Use a compact, low-impedance ground return for the amplifier and keep the feedback resistors close to the device to minimize parasitic coupling. Avoid routing the high-impedance input node beneath digital or switching traces. The OPA251UA is intended for low-frequency signals, but good layout still matters at sensor-level voltages where interference can be comparable to the signal being measured.
Do not interpret rail-to-rail output as an exact rail-to-rail swing guarantee. Check the OPA251 data sheet for output swing versus output load and temperature, and confirm that the input common-mode range includes the source signal at every operating corner. Its approximately 35 kHz gain-bandwidth product is also not sufficient for many high-frequency, precision-settling, or full-bandwidth audio applications.
Estimated: calculate linear dissipation as PD approximately equals (VIN - VOUT) multiplied by IOUT, plus VIN multiplied by IQ. Apply the calculated loss to the SOIC thermal model and compare the resulting junction temperature with the -40 C to 85 C operating range. These calculations are design estimates rather than guaranteed maxima; the final thermal assessment should use the manufacturer limits and the maximum expected supply, load, and ambient conditions.
コンプライアンス情報
The OPA251UA listing identifies the RoHS-compliant, lead-free, green device configuration. No additional REACH, halogen-free, conflict-minerals, or automotive qualification claim was established.