OPA349UA - 1uA, 70kHz Low-Power RRIO Op Amp | TI
部品番号: OPA349UA ✓ 生産中OPA349UA 概要
A rail-to-rail input/output operational amplifier, commonly called an RRIO op amp, amplifies the voltage difference between its two inputs while accepting input signals near or beyond the supply rails and producing output voltage close to the rails. This input/output flexibility makes the OPA349 useful in battery-powered sensors, portable instruments, and low-voltage measurement systems where signal headroom is limited.
The OPA349UA combines a 70 kHz gain-bandwidth product with only 1 µA of quiescent current. Its maximum input bias current is 10 pA, which is useful when source impedance is high and leakage or bias-current-induced offsets must remain small. The input common-mode range extends 200 mV beyond the power-supply rails, while the listed output drive current is 8 mA. Unity-gain stability supports direct use as a voltage follower.
The amplifier uses a CMOS implementation intended for low-power analog signal conditioning. Rail-to-rail operation increases usable input and output range at low supply voltages, while the modest 70 kHz bandwidth is better suited to precision, low-frequency, and instrumentation functions than to wideband signal processing. The single-channel configuration keeps each SOIC footprint dedicated to one amplifier.
Typical uses include battery-powered sensor interfaces, low-current buffer stages, portable measurement equipment, and sensor signal conditioning. The 1 µA quiescent current can extend battery life when the amplifier is continuously active, while the 70 kHz bandwidth provides useful closed-loop response for slowly varying analog signals.
Designers should account for the output-swing limit and common-mode behavior at each supply voltage. Input and output impedance, noise, offset, and stability also depend on source resistance, load, feedback network, and bypass capacitance, so the manufacturer datasheet should guide the final stability and layout review.
This page combines the key electrical characteristics of the OPA349UA with practical application guidance, verified compatibility information, and a structured comparison of related low-power operational amplifiers for design selection.
ドロップイン代替品: OPA349UA — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストOPA349UA 最大定格&電気的特性
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 70 kHz |
| 静止電流 | 1 µA |
| Maximum Input Bias Current | 10 pA |
| Input Common-Mode Range Beyond Supply Rails | 200 mV |
| Output Drive Current | 8 mA |
| Number of Channels | 1 circuit |
| Input Type | Rail-to-rail input |
| 出力タイプ | Rail-to-rail output |
| Gain Configuration | Unity-gain stable |
| 動作温度範囲 | 0 °C to +70 °C |
| パッケージ | 8-pin SOIC |
| RoHS ステータス | unknown |
| REACH Status | unknown |
OPA349UA 8-pin soic ピン配置ガイド
OPA349UA (8-pin soic パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: OPA349UA.
詳細は データシート をご参照ください。
主な用途
OPA349UA の用途: 6 件s: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Low-Current Buffer Stage, Industrial Low-Power Signal Chain, Portable Medical Sensor Interface, Low-Power Data Acquisition.
Battery-Powered Sensor Conditioning
The OPA349UA is suitable for conditioning outputs from high-impedance sensors operating from low-voltage battery rails. Its 1 µA quiescent current limits the amplifier's own standing load, while a maximum input bias current of 10 pA helps reduce bias-induced voltage errors at the sensor input. The 70 kHz gain-bandwidth product supports slow sensor signals rather than high-speed waveforms, and rail-to-rail input operation provides useful signal range near the supply limits. A unity-gain buffer configuration is appropriate when the source impedance is too high for downstream circuitry to load directly.
おすすめ
Portable Measurement Instrumentation
OPA349UA fits portable meters and low-current measurement front ends where battery life and usable signal range are both important. The 1 µA quiescent current reduces amplifier overhead, while the 70 kHz gain-bandwidth product provides enough loop bandwidth for many temperature, pressure, and position sensors. Rail-to-rail input and output behavior can increase measurement range in compact 3.3 V or 5 V systems. Gain and offset errors should be recalibrated around the selected sensor range, and the amplifier's DC offset and noise characteristics should be checked against the smallest input signal the instrument must resolve.
おすすめ
Low-Current Buffer Stage
The OPA349UA can serve as a low-current unity-gain buffer between a high-impedance source and a downstream load. Its 10 pA maximum input bias current is particularly useful when the source impedance is high, and its unity-gain stability supports direct voltage-follower use. The 8 mA listed output drive current provides more drive than the device's extremely low quiescent current might suggest, although load-dependent supply current must still be evaluated. Keep the feedback connection short, place the device close to the source, and avoid long PCB traces that can increase leakage, noise pickup, and sensitivity to capacitive loading.
おすすめ
Industrial Low-Power Signal Chain
OPA349UA is applicable to industrial monitoring circuits that operate from low-power rails and process relatively slow sensor signals. Its 1 µA quiescent current is useful in distributed or remotely powered monitoring equipment, while rail-to-rail input and output operation can reduce the need for an additional level-shifting stage. The 70 kHz gain-bandwidth product provides practical closed-loop bandwidth for low-frequency process variables and transducer outputs. Industrial qualification requirements, transient protection, noise immunity, and the accuracy drift across the deployed temperature range must be evaluated separately from the amplifier's core operating specifications.
おすすめ
Portable Medical Sensor Interface
OPA349UA can be used in low-power medical sensor interfaces when the system operates from a compact battery supply and requires rail-to-rail signal handling. Its 1 µA quiescent current helps limit continuous power consumption, and the 10 pA maximum input bias current is advantageous with high-impedance sensing elements. The 70 kHz bandwidth is appropriate for many physiological and biochemical signals after appropriate filtering. Medical-system designs must also evaluate input protection, leakage current, noise, electrode or sensor compatibility, alarm safety, and applicable regulatory requirements rather than treating the amplifier's generic specifications as system approval.
おすすめ
Low-Power Data Acquisition
OPA349UA is appropriate for slow, low-power data-acquisition channels that do not require the bandwidth of a general-purpose precision amplifier. Its 70 kHz gain-bandwidth product allows closed-loop operation across a broad range of useful gains, while the 1 µA quiescent current supports long operating life from a compact energy source. Rail-to-rail inputs and outputs maximize the usable range of a low-voltage converter. For multiplexed acquisition systems, allow the amplifier to settle after switching and ensure the selected gain, sampling rate, source impedance, and anti-alias filter are mutually consistent.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: OPA349UA — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | OPA2349UA | OPA349NA/250G4 |
|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | SOT-23-5 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 1 circuit | 2 circuits | 1 circuit |
| Operating Temperature Range | 0 °C to +70 °C | -40 °C to +70 °C | 0 °C to +70 °C |
主な差別化要因
- Very low quiescent current for a rail-to-rail CMOS amplifier (vs OPA2349UA)
- Single-channel packaging reduces unused circuitry (vs OPA2349UA)
- Low input bias current supports high-impedance sources (vs OPA349NA/250G4)
設計ノート
Do not assume that a rail-to-rail input amplifier accepts every possible input combination. The OPA349 input common-mode range extends 200 mV beyond the supply rails, but absolute maximum input voltage, supply sequencing, and input-current behavior still apply. Confirm these limits in the manufacturer datasheet before connecting a sensor that can exceed the operating rail. Keep the feedback network and input source impedances compatible with the recommended bias-current and stability limits.
Place the OPA349 close to the source and load rather than routing sensitive signals across a large portion of the board. Keep the output path short, provide a solid ground return, and decouple the supply pins according to the manufacturer application guidance. Sensitive input nodes should be kept away from switching nodes and high-current return paths. Because the amplifier can operate with very low bias current, board contamination and flux residue may matter more than in a conventional higher-current amplifier design.
Estimated: at a 3.3 V supply and 1.5 V output, the ideal linear-regulator dissipation attributable to 1 µA amplifier current is approximately 1.8 µW, calculated as (3.3 V - 1.5 V) × 1 µA. Actual system consumption is higher because bias current, load current, regulator quiescent current, leakage, and switching overhead add to the total. This calculation illustrates why the OPA349 is valuable in battery-powered designs, but it is not a substitute for measuring the complete analog subsystem.
The 70 kHz gain-bandwidth product means that closed-loop bandwidth decreases as noise gain increases. Check settling time, capacitive loading, and feedback-network impedance using the datasheet models and recommended application circuit. A voltage follower is suitable for unity-gain buffering, but higher-gain configurations need the correct feedback resistors and compensation. If driving a significant capacitive load, keep the load local and verify stability on the final PCB rather than relying only on simulation.
コンプライアンス情報
The cited excerpts do not establish material-compliance declarations for the exact OPA349UA orderable MPN. Automotive qualification is not indicated for this standard-product option.