Texas Instruments

OPA349UA - 1uA, 70kHz Low-Power RRIO Op Amp | TI

MPN: OPA349UA ✓ 啟用中
5.5 V Vdss 1 µA Id 8-pin SOIC Package
MOQ: 1 |

OPA349UA 概覽

Texas Instruments OPA349UA is a single-circuit, rail-to-rail input and output CMOS operational amplifier featuring 70 kHz gain-bandwidth product, 1 µA quiescent current, and operation up to a 5.5 V supply in an 8-pin SOIC package. It is optimized for portable instrumentation and other low-power analog systems.

A rail-to-rail input/output operational amplifier, commonly called an RRIO op amp, amplifies the voltage difference between its two inputs while accepting input signals near or beyond the supply rails and producing output voltage close to the rails. This input/output flexibility makes the OPA349 useful in battery-powered sensors, portable instruments, and low-voltage measurement systems where signal headroom is limited.

The OPA349UA combines a 70 kHz gain-bandwidth product with only 1 µA of quiescent current. Its maximum input bias current is 10 pA, which is useful when source impedance is high and leakage or bias-current-induced offsets must remain small. The input common-mode range extends 200 mV beyond the power-supply rails, while the listed output drive current is 8 mA. Unity-gain stability supports direct use as a voltage follower.

The amplifier uses a CMOS implementation intended for low-power analog signal conditioning. Rail-to-rail operation increases usable input and output range at low supply voltages, while the modest 70 kHz bandwidth is better suited to precision, low-frequency, and instrumentation functions than to wideband signal processing. The single-channel configuration keeps each SOIC footprint dedicated to one amplifier.

Typical uses include battery-powered sensor interfaces, low-current buffer stages, portable measurement equipment, and sensor signal conditioning. The 1 µA quiescent current can extend battery life when the amplifier is continuously active, while the 70 kHz bandwidth provides useful closed-loop response for slowly varying analog signals.

Designers should account for the output-swing limit and common-mode behavior at each supply voltage. Input and output impedance, noise, offset, and stability also depend on source resistance, load, feedback network, and bypass capacitance, so the manufacturer datasheet should guide the final stability and layout review.

This page combines the key electrical characteristics of the OPA349UA with practical application guidance, verified compatibility information, and a structured comparison of related low-power operational amplifiers for design selection.

直接替換替代品,適用於 OPA349UA — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此產品無可直接替換的替代品。

申請替代品

OPA349UA 最大額定值與電氣特性

Maximum Supply Voltage 5.5 V
Gain-Bandwidth Product 70 kHz
靜態電流 1 µA
Maximum Input Bias Current 10 pA
Input Common-Mode Range Beyond Supply Rails 200 mV
Output Drive Current 8 mA
Number of Channels 1 circuit
Input Type Rail-to-rail input
輸出類型 Rail-to-rail output
Gain Configuration Unity-gain stable
工作溫度範圍 0 °C to +70 °C
封裝 8-pin SOIC
RoHS 狀態 unknown
REACH Status unknown

OPA349UA 8-pin soic 腳位配置指南

OPA349UA(8-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。

OPA349UA 的 8-pin soic 封裝腳位圖

無詳細腳位定義資料: OPA349UA.

請參閱 資料表 以查看完整腳位配置。

典型應用

OPA349UA 適用於 6 應用s: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Low-Current Buffer Stage, Industrial Low-Power Signal Chain, Portable Medical Sensor Interface, Low-Power Data Acquisition.

🧩

Battery-Powered Sensor Conditioning

The OPA349UA is suitable for conditioning outputs from high-impedance sensors operating from low-voltage battery rails. Its 1 µA quiescent current limits the amplifier's own standing load, while a maximum input bias current of 10 pA helps reduce bias-induced voltage errors at the sensor input. The 70 kHz gain-bandwidth product supports slow sensor signals rather than high-speed waveforms, and rail-to-rail input operation provides useful signal range near the supply limits. A unity-gain buffer configuration is appropriate when the source impedance is too high for downstream circuitry to load directly.

🖥️

Portable Measurement Instrumentation

OPA349UA fits portable meters and low-current measurement front ends where battery life and usable signal range are both important. The 1 µA quiescent current reduces amplifier overhead, while the 70 kHz gain-bandwidth product provides enough loop bandwidth for many temperature, pressure, and position sensors. Rail-to-rail input and output behavior can increase measurement range in compact 3.3 V or 5 V systems. Gain and offset errors should be recalibrated around the selected sensor range, and the amplifier's DC offset and noise characteristics should be checked against the smallest input signal the instrument must resolve.

🔧

Low-Current Buffer Stage

The OPA349UA can serve as a low-current unity-gain buffer between a high-impedance source and a downstream load. Its 10 pA maximum input bias current is particularly useful when the source impedance is high, and its unity-gain stability supports direct voltage-follower use. The 8 mA listed output drive current provides more drive than the device's extremely low quiescent current might suggest, although load-dependent supply current must still be evaluated. Keep the feedback connection short, place the device close to the source, and avoid long PCB traces that can increase leakage, noise pickup, and sensitivity to capacitive loading.

🏭

Industrial Low-Power Signal Chain

OPA349UA is applicable to industrial monitoring circuits that operate from low-power rails and process relatively slow sensor signals. Its 1 µA quiescent current is useful in distributed or remotely powered monitoring equipment, while rail-to-rail input and output operation can reduce the need for an additional level-shifting stage. The 70 kHz gain-bandwidth product provides practical closed-loop bandwidth for low-frequency process variables and transducer outputs. Industrial qualification requirements, transient protection, noise immunity, and the accuracy drift across the deployed temperature range must be evaluated separately from the amplifier's core operating specifications.

💊

Portable Medical Sensor Interface

OPA349UA can be used in low-power medical sensor interfaces when the system operates from a compact battery supply and requires rail-to-rail signal handling. Its 1 µA quiescent current helps limit continuous power consumption, and the 10 pA maximum input bias current is advantageous with high-impedance sensing elements. The 70 kHz bandwidth is appropriate for many physiological and biochemical signals after appropriate filtering. Medical-system designs must also evaluate input protection, leakage current, noise, electrode or sensor compatibility, alarm safety, and applicable regulatory requirements rather than treating the amplifier's generic specifications as system approval.

📡

Low-Power Data Acquisition

OPA349UA is appropriate for slow, low-power data-acquisition channels that do not require the bandwidth of a general-purpose precision amplifier. Its 70 kHz gain-bandwidth product allows closed-loop operation across a broad range of useful gains, while the 1 µA quiescent current supports long operating life from a compact energy source. Rail-to-rail inputs and outputs maximize the usable range of a low-voltage converter. For multiplexed acquisition systems, allow the amplifier to settle after switching and ensure the selected gain, sampling rate, source impedance, and anti-alias filter are mutually consistent.

推薦產品摘要

OPA349UA Texas Instruments 用於: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Low-Current Buffer Stage, Industrial Low-Power Signal Chain, Portable Medical Sensor Interface, Low-Power Data Acquisition OPA2349UA Dual-family option for paired sensing channels 用於: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Low-Current Buffer Stage, Industrial Low-Power Signal Chain, Portable Medical Sensor Interface, Low-Power Data Acquisition
What are the key specifications of OPA349UA that engineers should know?
The OPA349UA is a single-circuit, 70 kHz, 1 µA rail-to-rail input/output CMOS operational amplifier supplied in an 8-pin SOIC package. According to the Texas Instruments OPA349 datasheet, its maximum supply voltage is 5.5 V, maximum input bias current is 10 pA, and the input common-mode range extends 200 mV beyond the supply rails. The amplifier is unity-gain stable and has a listed output drive current of 8 mA. These characteristics make it particularly relevant to battery-powered sensing, portable instrumentation, and low-current analog signal-conditioning designs.
Where can I download the OPA349UA datasheet PDF?
The official OPA349UA datasheet PDF is available from Texas Instruments at the manufacturer's SBOS121B datasheet URL. It covers the OPA349 single-amplifier family, including the OPA349UA ordering option, and provides the electrical characteristics needed for supply, input, output, noise, and stability design work. Use the pin-description table in that document when assigning PCB tracks and confirming the 8-pin SOIC connection. The manufacturer product page also links supporting ordering, quality, and application information.
Where can I find the OPA349UA pinout?
The OPA349UA pin assignment is documented in the pin-configuration section of the official Texas Instruments OPA349 datasheet. This orderable option uses the 8-pin SOIC package, so verify the outline, lead pitch, and pin numbering against the package drawing before laying out the PCB. The datasheet connection diagram also identifies the supply pins, input terminals, output terminal, and the NC or offset-trim-related positions where applicable. Do not infer the footprint solely from the UA ordering suffix.
What is the OPA349UA supply voltage range?
The Texas Instruments product information identifies the OPA349 as a single, 5.5 V maximum-supply, 70 kHz operational amplifier with 1 µA quiescent current. The manufacturer documentation clearly specifies the upper limit as 5.5 V, while the exact minimum operating supply is not stated in the supplied technical excerpt. Before selecting the device for a new rail, use the Recommended Operating Conditions table in the official OPA349 datasheet to confirm the lower voltage, supply-current behavior, and common-mode limits.
Is OPA349UA suitable for battery-powered sensor interfaces?
The OPA349UA is suitable for many battery-powered sensor interfaces because its quiescent current is only 1 µA and its gain-bandwidth product is 70 kHz. Its rail-to-rail input and output behavior can improve signal utilization in low-voltage systems, and the 10 pA maximum input bias current helps when working with high-impedance sensors. The amplifier is unity-gain stable and supports direct buffering. Sensor excitation current, leakage, settling requirements, and total system noise should still be evaluated because the amplifier is optimized for low-frequency precision rather than high-bandwidth acquisition.
OPA349UA vs OPA2349UA - which is better for a dual amplifier design?
OPA2349UA is the better choice when a dual-amplifier circuit is required because it contains two amplifiers in an 8-pin SOIC, whereas OPA349UA contains one circuit. The comparison result identifies OPA2349UA/2K5 as a dual rail-to-rail 70 kHz amplifier and OPA349UA as a single 8-SOIC amplifier. Both belong to the same low-power CMOS product family, but the dual device reduces the number of packages and allows closely related signal paths to share a footprint. OPA349UA remains preferable when only one amplifier is needed or when independent package placement is valuable.
When should I choose OPA349UA over OPA2349UA?
Choose OPA349UA when the circuit needs only one amplifier, particularly in compact battery-powered equipment where minimizing package count matters less than using an individual low-power channel. Choose OPA2349UA when the design needs two amplifiers in one 8-pin SOIC, such as matched instrumentation channels, paired gain stages, or a shared bias arrangement. Both family members provide a 70 kHz gain-bandwidth product and are designed around low-power rail-to-rail operation. Package count, channel independence, routing symmetry, and acquisition-channel requirements should determine the final selection.
What can replace OPA349UA?
OPA349UA should be replaced only by an amplifier with the same 8-pin SOIC footprint, matching supply range, rail-to-rail input and output behavior, adequate bandwidth, and compatible bias-current and offset requirements. The verified cross-reference results did not identify a specific cross-brand part that could be confirmed as a true drop-in replacement. Use the manufacturer cross-reference resources or the Request a Quote form on this page to identify a candidate, then compare the full electrical tables and pin descriptions before approving it for production.
What is the best Analog Devices equivalent for OPA349UA?
No Analog Devices equivalent is listed here because the available cross-reference information did not establish a pin-compatible, electrically equivalent 8-pin SOIC candidate. A valid substitute must support the required supply voltage, provide rail-to-rail input and output operation, deliver sufficient gain-bandwidth product, and preserve acceptable bias current, offset, noise, and output-drive characteristics. Treat a similar low-power amplifier as a candidate rather than a guaranteed drop-in replacement, and verify its pinout and application limits against the OPA349UA requirements.
Where to buy OPA349UA online?
Use the Request a Quote form on this page to request OPA349UA availability, lead time, order quantity, and delivery options. The form keeps the inquiry tied to the exact OPA349UA ordering code and helps distinguish a standard 8-pin SOIC component from related single-amplifier package options. For production planning, request confirmation of lifecycle status, standard packing quantity, and traceable stock rather than relying on a generic family-level listing.
What is the price of OPA349UA?
Request the current OPA349UA price through the Request a Quote form on this page. The form supports quantity-break inquiries for the exact 8-pin SOIC ordering code and avoids presenting a stale unit price as current. For production purchasing, provide the required annual usage, forecast horizon, accepted delivery schedule, and packaging preference so the returned quotation reflects the intended supply plan.
What is the lead time and stock status for OPA349UA?
Request current stock and lead-time confirmation through the Request a Quote form on this page. Lead time can vary with order quantity, packaging, production scheduling, and regional logistics, so a family-level availability statement is not sufficient for a production commitment. Include your required quantity, target delivery date, acceptable package form, and whether unbroken or date-code traceability is required. The manufacturer product page is the authoritative starting point for lifecycle and ordering information.
Is OPA349UA in stock?
Current OPA349UA stock should be confirmed through the Request a Quote form on this page because inventory changes with order size and supplier allocation. Include the exact quantity required and the desired shipment date in the request. If the design is entering qualification, ask for lifecycle status, standard packing details, and traceability information in addition to the stock count so procurement can distinguish immediately available material from production-scheduled supply.
How much bandwidth does OPA349UA provide?
The OPA349UA provides a 70 kHz gain-bandwidth product and is unity-gain stable. According to the Texas Instruments datasheet, this low-power amplifier is intended for battery-powered applications where low quiescent current and rail-to-rail operation are more important than wideband performance. A closed-loop bandwidth lower than 70 kHz results from the selected feedback network and noise gain, so use the amplifier's AC specifications to size the gain, input capacitance, and load for the required settling behavior.
Is OPA349UA RoHS compliant?
The RoHS status of OPA349UA is not established by the cited manufacturer and distributor excerpts, so it should not be assumed for a released BOM. Confirm the current declaration using the Texas Instruments product page, the manufacturer material-compliance documentation, or supplier documentation attached to the exact orderable MPN. The same review should determine REACH, lead-free, halogen-free, and conflict-minerals declarations for the intended shipment. Compliance status can vary by product family, revision, and date of manufacture.

工程參考資料,適用於 OPA349UA — 比較、設計指引及合規資訊。

選型指南

Choose OPA349UA when the design needs one low-power rail-to-rail amplifier, especially in battery-powered instrumentation or a high-impedance sensor interface. Its 1 µA quiescent current, 10 pA maximum input bias current, and 70 kHz gain-bandwidth product fit low-frequency precision and signal-conditioning applications. Choose OPA2349UA when two amplifiers are required in one 8-pin SOIC, reducing package count and supporting paired channels. OPA349NA/250G4 is the same-family single-amplifier option in SOT-23-5, which can improve board density but requires a different footprint and careful handling of the exposed thermal and electrical pad. No cross-brand replacement is recommended without verifying the complete electrical tables, pin configuration, stability, and qualification requirements.

與替代品比較

參數 本產品 OPA2349UA OPA349NA/250G4
Package 8-pin SOIC 8-pin SOIC SOT-23-5
Brand Texas Instruments Texas Instruments Texas Instruments
Number of Amplifiers 1 circuit 2 circuits 1 circuit
Operating Temperature Range 0 °C to +70 °C -40 °C to +70 °C 0 °C to +70 °C

主要差異化特點

  • Very low quiescent current for a rail-to-rail CMOS amplifier (對比OPA2349UA)
  • Single-channel packaging reduces unused circuitry (對比OPA2349UA)
  • Low input bias current supports high-impedance sources (對比OPA349NA/250G4)

設計說明

Do not assume that a rail-to-rail input amplifier accepts every possible input combination. The OPA349 input common-mode range extends 200 mV beyond the supply rails, but absolute maximum input voltage, supply sequencing, and input-current behavior still apply. Confirm these limits in the manufacturer datasheet before connecting a sensor that can exceed the operating rail. Keep the feedback network and input source impedances compatible with the recommended bias-current and stability limits.

Place the OPA349 close to the source and load rather than routing sensitive signals across a large portion of the board. Keep the output path short, provide a solid ground return, and decouple the supply pins according to the manufacturer application guidance. Sensitive input nodes should be kept away from switching nodes and high-current return paths. Because the amplifier can operate with very low bias current, board contamination and flux residue may matter more than in a conventional higher-current amplifier design.

Estimated: at a 3.3 V supply and 1.5 V output, the ideal linear-regulator dissipation attributable to 1 µA amplifier current is approximately 1.8 µW, calculated as (3.3 V - 1.5 V) × 1 µA. Actual system consumption is higher because bias current, load current, regulator quiescent current, leakage, and switching overhead add to the total. This calculation illustrates why the OPA349 is valuable in battery-powered designs, but it is not a substitute for measuring the complete analog subsystem.

The 70 kHz gain-bandwidth product means that closed-loop bandwidth decreases as noise gain increases. Check settling time, capacitive loading, and feedback-network impedance using the datasheet models and recommended application circuit. A voltage follower is suitable for unity-gain buffering, but higher-gain configurations need the correct feedback resistors and compensation. If driving a significant capacitive load, keep the load local and verify stability on the final PCB rather than relying only on simulation.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The cited excerpts do not establish material-compliance declarations for the exact OPA349UA orderable MPN. Automotive qualification is not indicated for this standard-product option.

相關搜尋

OPA349UA datasheet OPA349UA pinout OPA349UA datasheet pdf OPA349UA equivalent OPA349UA replacement OPA349UA price OPA349UA stock Texas Instruments OPA349UA OPA349UA 1uA 70kHz OPA349UA 8-SOIC footprint OPA349UA battery powered sensor OPA349UA vs OPA2349UA OPA349 application circuit OPA349 low power op amp

相關元件與詞彙

Texas Instruments OPA349UA OPA349 OPA2349UA OPA349NA/250G4 operational amplifier CMOS operational amplifier rail-to-rail input rail-to-rail output RRIO amplifier precision amplifier low-power amplifier gain-bandwidth product quiescent current input bias current input common-mode range unity-gain stable 8-pin SOIC SOT-23-5 surface-mount package battery-powered instrumentation sensor signal conditioning portable measurement equipment semiconductor
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情